1. Manuals
  2. Brands
  3. FS.COM Manuals
  4. Switch
  5. ELPS
  6. Configuration manual

FS.COM ELPS Configuration Manual

48-port stackable gigabit switch with sfp+ uplink
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ELPS Configuration Commands

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the ELPS and is the answer not in the manual?

Questions and answers

Summary of Contents for FS.COM ELPS

  • Page 1 ELPS Configuration Commands...

  • Page 2: Table Of Contents

    Table of Contents Table of Contents Chapter 1 ELPS Configuration Commands ........................1 1.1 Global Commands............................1 e e l l p p s s id 1.1.1 .............................. 1 w w o o r r k k i i n n g g - - v v l l a a n n m m a a p p vlanmap 1.1.2...

  • Page 3: Chapter 1 Elps Configuration Commands

    Chapter 1 ELPS Configuration Commands 1.1 Global Commands elps id 1.1.1 To set an instance of ELPS node and enter the node mode, run the following command: elps id To cancel an instance of ring, run the following command: no elps id...

  • Page 4: W W O O R R K K I I N N G G - - V V L L A A N N M M A A P P Vlanmap

    {1plus1-bidirectional | 1plus1-unidirectional | 1to1-bidirectional} revertive-mode {revertive | nonrevertive} detect-fault {physical-port-check| continuity-check | both-check} 1.1.3 protection-mode {1plus1-bidirectional 1plus1-unidirectional 1to1-bidirectional} To set the protection mode of the ELPS node to be the 1plus1-bidirectional mode, run the following command: - 2 -...
  • Page 5 To set the protection mode of the ELPS node to be the 1plus1-unidirectional mode, run the following command: protection-mode 1plus1-unidirectional To set the protection mode of the ELPS node to be the 1to1-bidirectional mode, run the following command: protection-mode 1to1-bidirectional Parameter N/A.

  • Page 6: R R E E V V E E R R T T I I V V E E - - M M O O D D E E { { R R E E V V E E R R T T I I V V E E N N O O N N R R E E V V E E R R T T I I V V E E

    ELPS Configuration Commands revertive-mode {revertive | nonrevertive} 1.1.4 To set the mode of the ELPS to revertive, run the following command: revertive-mode revertive To set the mode of the ELPS to non-revertive, run the following command: revertive-mode nonrevertive Parameter N/A.

  • Page 7: D D E E T T E E C C T T - - F F A A U U L L T T { { P P H H Y Y S S I I C C A A L L - - P P O O R R T T - - C C H H E E C C K K C C O O N N T T I I N N U U I I T T Y Y - - C C H H E E C C K K B B O O T T H H - - C C H H E E C C K K

    To set the trouble monitoring mode of the ELPS node to continuity-check, run the following command: detect-fault continuity-check To set the trouble monitoring mode of the ELPS node to both-check, run the following command: detect-fault both-check Default value By default, the ELPS node’s trouble monitoring mode is not configured.

  • Page 8: W W T T R R - - T T I I M M E E

    ELPS Configuration Commands WTR-time 1.1.6 To set the WTR time of the ELPS node, run the following command: WTR-time value To resume the default WTR time of the ELPS node, run the following command: no WTR-time Parameter Parameter Description value Stands for the WTR time, which ranges from 5 to 12 minutes.

  • Page 9: Port Configuration Commands

    S1_config_elps1#protection-mode 1plus1-bidirectional S1_config_elps1#revertive-mode revertive S1_config_elps1#detect-fault continuity-check S1_config_elps1#hold-off-time 2 S1_config_elps1# Related command 1.2 Port Configuration Commands elps id {working-transport | protection-transport} 1.2.1 To set a port where the ELPS working transport entity is located, run the following command: - 7 -...
  • Page 10 To delete the ELPS working transport entity configuration on a port, run the following command: no elps id working-transport To set a port where the ELPS protection transport entity is located, run the following command: elps id protection-transport To delete the ELPS protection transport entity configuration on a port, run the following...

  • Page 11: E E L L P P S S Id M M E E P P M M D D Md-String M M A A Ma-String L L E E V V E E L L Level-Id L L O O C C A A L L Local-Id R R E E M M O O T T E E Remote-Id

    1.2.2 remote remote-id To set the MEP information about the ELPS port, run the following command: elps id mep md md-string ma ma-string level level-id local local-id remote remote-id...

  • Page 12: Control Commands

    ELPS Configuration Commands 1.3 Control Commands elps id LockOut 1.3.1 To set the protection lockout of ELPS, run the following command: elps id LockOut Parameter Parameter Description ID of the node Default value N/A. Command mode Monitoring mode Explanation N/A.

  • Page 13: E E L L P P S S Id F F O O R R C C E E D D S S W W I I T T C C H H

    ELPS Configuration Commands elps id ForcedSwitch 1.3.2 To set the forced switching operation of ELPS, run the following command: elps id ForcedSwitch Parameter Parameter Description ID of the node Default value N/A. Command mode Monitoring mode Explanation N/A. Example N/A.

  • Page 14: E E L L P P S S M M A A N N U U A A L L S S W W I I T T C C H H - - W W O O R R K K I I N N G G

    ForcedSwitch elps id ManualSwitch-Working elps id Exercise elps id CLEAR 1.3.4 elps id ManualSwitch-Working To switch to the working entity of ELPS manually, run the following command: elps id ManualSwitch-Working Parameter Parameter Description ID of the node - 12 -...

  • Page 15: Id E E X X E E R R C C I I S S E E

    LockOut elps id ForcedSwitch elps id ManualSwitch elps id Exercise elps id CLEAR 1.3.5 elps id Exercise To set the exercise operation of ELPS, run the following command: elps id Exercise Parameter Parameter Description ID of the node Default value N/A.

  • Page 16: E E L L P P S S Id C C L L E E A A R R

    LockOut elps id ForcedSwitch elps id ManualSwitch elps id ManualSwitch-Working elps id CLEAR 1.3.6 elps id CLEAR To clear the control command of ELPS, run the following command: elps id CLEAR Parameter Parameter Description ID of the node Default value N/A.

  • Page 17: Show

    Exercise 1.4 Show show elps 1.4.1 To display the summary information about the ELPS node, run the following command: show elps id To display the detailed information about the ELPS node, run the following command: show elps id detail...
  • Page 18 ELPS Configuration Commands Default value N/A. Command mode Monitoring mode, global configuration mode, node configuration mode or port configuration mode Explanation N/A. Example N/A. Related command N/A. - 16 -...

Table of Contents