Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zenesis ZN-502 A
Summary of Contents for Zenesis ZN-502 A
- Page 1 ZN-502 A/S/AS USER MANUAL...
- Page 2 Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install.
- Page 3 3. If any defects are discovered, do not open or attempt to repair the system. Ask the installer for assistance. 4. Zenesis Electronics Corporation will not be responsible for any theft and/or damages to your vehicle. 5. The user of this system will be responsible for any injuries and/or damages resulting from misuse.
-
Page 4: Table Of Contents
CONTENTS 1. Introduction System Contents Remote Control Button Layout LCD Display Introduction Remote Control Button Introduction 2. Primary Features Door Lock (Arm) Door Unlock (Disarm) Arm / Disarm Status Car Find & Status LCD Screen Status Panic Remote Start Trunk Release Valet Mode 3. -
Page 5: System Contents
1. INTRODUCTION System Contents Remote Control Button Layout LCD Display Introduction Remote Control Button Introduction... - Page 6 1.1 System Contents Main Control Module Remote Control Antenna...
- Page 7 Wiring Harness Z-PASS TOUCH Shock Sensor Manuals Siren...
-
Page 8: Specifications
1.2 Remote Control Button Layout Front View Antenna OLCD / UCLCD CAUTION NEVER use the system except for its intended use. This is an electronic system with complex circuitry. Avoid dropping the components or cause any other physical damage as that will void the warranty. Buttons Battery 1.5 V Back... - Page 9 Button(s) Duration* Description 0.5 sec Arm / Door Lock Ⅰ 0.5 sec Disarm / Door Unlock Ⅱ Ⅲ× 3 Times 0.5 sec Remote Control Hold ON/OFF 0.5 sec Vehicle Status / Car Finder Ⅳ Ⅰ - 2+ sec Panic 2+ sec Remote Start Ⅲ- 2 sec...
-
Page 10: Remote Control Button Introduction
1.4 Remote Control Button Introduction... -
Page 11: 2. Primary Features
LEGEND: “ - “ means to hold for 2 seconds - press and hold button(s) until 1st beep is heard from the remote control. “ ~ “ means to hold for 4 seconds - press and hold button(s) until 2nd beep are heard from the remote control. Status Z-Pass LED’s Armed Mode... -
Page 12: Door Lock (Arm)
Arm (Door Lock) Disarm (Door Unlock) Arm / Disarm Status Car Find & Status LCD Screen Status Panic Remote Start Trunk Release Valet Mode 2.1 Door Lock (Arm) ButtonⅠ 0.5 sec Successful Arm (Door Lock) Remote Control & flash. 1 beep will occur. 1 parking light flash &... - Page 13 Successful Disarm (Door Unlock) & will blink until remote start is turned off. 1 beep will occur if the main Remote Control control module communicates with the remote control. 5 beeps will occur after remote start is successful. 1 parking light flash & 1 siren chirp if the main control module communicates with the Vehicle remote control.
- Page 14 LED on the Antenna Module will indicate the status of the system. If a door is opened and closed, the Triggered Alarm status & & will blink. 2 Remote Control on the Z-Pass will be beeps will occur. cleared. Vehicle 2 x parking light flashes &...
-
Page 15: Panic
Remote Start On Shock Sensor Trigger Option 1 Input Trigger 2.5 Remote Control Hold ButtonⅢ 0.5 sec x 3 Times Pressing Button Ⅲ 3 times for 0.5 second each will put the remote control buttons into “Hold” mode. Any button presses will be ignored. To come out of “Hold” mode, press Button III 3 times for 0.5 second each again. -
Page 16: Remote Start
If Button Ⅲ is pressed for 2+ seconds while remote start is on, remote start will turn off. The default remote start engine running time is 15 minutes. The time can be changed through the User Programmable Options. CAUTION: Do not use the remote start feature if the vehicle is in an enclosed area. Do not use the remote start feature where laws prevent its usage. -
Page 17: Valet Mode
Valet mode OFF Valet mode without remote control (Emergency shut off) 1. Insert the key into the key cylinder and turn to the ON position. 2. Within 3 seconds, press the foot brake 6 times. 3. On the 6 press, hold down the foot brake until 1 parking light flash and 1 siren chirp occur. -
Page 18: Remote Control Beep Mute
3.SECONDARY FEATURES Remote Control Beep Mute Siren Mute Passive Lock (Arm) Safety Relock (Rearm) Ignition Lock Cold Start Timer Turbo Timer Option 1 Input Remote Control Registration 3.10 Remote Start Reservation 3.11 User Programmable Options 3.12 Time, Time Alarm, Timer Remote Start Reservation Set 3.13 Aux 1 Output 3.14 Aux 2 Output 3.15 Shock Sensor Option... - Page 19 Siren Mute OFF - Siren ON & will blink. will turn Remote Control OFF. 2 parking light flashes & 2 siren chirps Vehicle 3.3 Passive Arm (Lock) ButtonsⅠ+Ⅱ 4 sec + Brake Pedal To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + II are pressed for 4 seconds.
-
Page 20: Ignition Lock
armed state and the system is disarmed but a door is not opened, the system will Safety Rearm automatically within 30 seconds. Safety Rearm (Relock) ON & will blink. will Remote Control stay ON. 1 parking light flash & 1 siren chirp Vehicle Safety Rearm (Relock) OFF &... -
Page 21: Turbo Timer
remote start is turned ON, the timer will automatically restart once the engine is turned OFF. The timer can be set through the User Programmable Options. Cold start timer ON Remote Control & will blink. will stay ON. 1 parking light flash & 1 siren chirp Vehicle Cold start timer OFF &... -
Page 22: Option 1 Input
area. Do not idle the vehicle if any laws prohibit this action. Do not idle the vehicle if it is a convertible or open concept type of vehicle. 3.8 Option 1 Input Additional sensors can be added to the system using Option 1 input. No additional programming is required. -
Page 23: User Programmable Options
remote start reservation modes: automatic and manual. Please note that automatic and manual do not refer to the transmission type. Rather, automatic and manual refer to the type of remote start reservation. 1. Automatic Remote Start Reservation (Default) a. Before turning off the engine, put the transmission into Neutral. Ensure that the parking brake (emergency brake) is engaged. - Page 24 Options Button User Option Sequence Ⅰ Ⅱ Ⅲ Ⅳ → Ⅰ Remote Start Run Time 15 min 5 min 25 min Ⅳ → Ⅱ Diesel Warm Up Time 30 sec 15 sec 7.5 sec Ⅳ → Ⅲ Siren Sound Time 30 sec 70 sec 100 sec...
- Page 25 ButtonⅠ : Time Menu (Time → Alarm→ Remote Start Timer) 4. Triggers The following triggers will occur ONLY when the system is armed. Shock Trigger & will blink. The Remote Control remote control will beep or vibrate. Parking lights will flash and siren will Vehicle sound.
-
Page 26: Aux 1 Output
ButtonⅡ : Hours setting. WARRANTY CARD Press and/or hold Button II in order to increase the hours value. Button Ⅲ : Minutes setting. Use this warranty card for your records. Please go to Press and/or hold Button III in order to increase the minutes value. www.zenesisalarms.com Button Ⅳ: Confirmation or rejection.
Need help?
Do you have a question about the ZN-502 A and is the answer not in the manual?
Questions and answers