Table of Contents
Advertisement
Quick Links
Mini4 Dual Sonar Interface Board
(P/N 201630-xxx)
User's Manual
And
Troubleshooting Guide
February 23, 2009
Rev B
Moog Components Group
Springfield Operations
750 West Sproul Road
Springfield, PA 19064
E-Mail:
mcg@moog.com
URL:
www.moog.com/components
Tel: 610-328-4000 Fax 610-605-6216
24/7 Technical Customer Support Hotline: 610-605-6101
Advertisement
Table of Contents
Summary of Contents for PRIZM Mini4
- Page 1 Mini4 Dual Sonar Interface Board (P/N 201630-xxx) User’s Manual Troubleshooting Guide February 23, 2009 Rev B Moog Components Group Springfield Operations 750 West Sproul Road Springfield, PA 19064 E-Mail: mcg@moog.com URL: www.moog.com/components Tel: 610-328-4000 Fax 610-605-6216 24/7 Technical Customer Support Hotline: 610-605-6101...
-
Page 2: Table Of Contents
Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 MANUAL REVISION HISTORY REVISION DATE REASON FOR NUMBER REVISION Preliminary 10/26/06 ORIGINAL 4/19/09 UPDATED 2/23/09 Updated contact information to reflect Moog Components Group TABLE OF CONTENTS MINI4 DUAL SONAR BOARD, P/N: 201630-XXX............... 3 : ................ -
Page 3: Mini4 Dual Sonar Board, P/N: 201630-Xxx
2/23/09 1 Mini4 Dual Sonar Board, P/N: 201630-xxx The Prizm Mini4 Dual Sonar Board provides two independent fiber optic links to remote the Reson 8xxx and Simrad EM3002 single/dual beam sonars. The Dual Sonar Board can be jumper selected to support both single-ended (single coax) Reson sonars and differential (dual coax) Simrad sonars. -
Page 4: Dual Sonar Board Indicators And Controls
Mini4 Video Input or Output board. NOTE: To complete the RS-485 diagnostics link from the surface to the subsea boars, the Dual Sonar Board must be stacked onto a Mini4 Video Input or Output board to complete the link over the multiplexer’s fiber. - Page 5 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 FUSES: There are four fuses for this board, all fuses are the self-resetting PTC type and will not require replacement by the user. 2.6 Amp PTC, +5VDC input fuse at J8 2.6 Amp PTC, +5VDC input fuse for Diag header at J4 –...
- Page 6 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 Diagnostics Header o o 2 o o 4 o o 6 o o 8 o o 10 There are two Phoenix pluggable connectors 3-pin Phoenix, RS-485 Diagnostics Diagnostics Connector...
- Page 7 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 There is one header for programming the Lattice programmable device J12: ISP programming header, do not use ISP Header +3.3V o o 2 o o 4 o o 6 o o 8 NOTE: J12 to be used only by PRIZM.
- Page 8 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 JP8: Laser enable/disable select for link A to enable laser to disable laser JP10: Input/Output select for IN/OUT A- connector (J7) 3 o OUT 3 o OUT 2 o for INPUT...
- Page 9 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 JP15: Output B CD/Mute Selection Disable Mute 2 o for CD Mute 2 o for LSI Mute JP18: Single-ended/Differential select for link B 3 o S 3 o S...
- Page 10 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 JP20: Input/Output select for link B 1 o IN 1 o IN 2 o for INPUT 2 o for OUTPUT 3 o OUT 3 o OUT For factory configuration, jumper posts JP3-6, 11, 14, 16 are selectable.
-
Page 11: Mini4 Dual Sonar Board Specifications
Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 JP14: Eye monitor, “B” Output 1 o test point 2 o GND JP16: Eye monitor, “B” Input 1 o test point 2 o GND 1.3.2 Mini4 Dual Sonar Board Specifications:... -
Page 12: Optical Section Testing
• The optical transceiver module is defective at either the surface or subsea board. • Excessive light loss (low received optical power) is being experienced. • The Mini4 board (not the optical transceiver module) is malfunctioning. • There is not enough attenuation in the optical link and the receiver is saturating. -
Page 13: Stack Mini4 System Installation Checkout Procedure
2/23/09 • If any of the LEDs are not operating correctly check one of the other channels. If the LEDs operate on that channel, replace the Mini4 board with a spare board or use the working channels only. 1.4 Stack Mini4 System Installation Checkout Procedure NOTE: The Dual Sonar Board will work in a stand-alone configuration without stacking the boards above a Mini4 Video Input or Output board. - Page 14 Moog Components Group 201630-xxx Mini4 Dual Sonar Board Manual, Preliminary 2/23/09 Figure 1- Typical Cabling/Wiring for Back plane Diagnostics Telemetry Page 14 of 14...