Subscribe to Our Youtube Channel
Related Manuals for TimberPro HT 260
Summary of Contents for TimberPro HT 260
- Page 1 OWNER’S MANUAL GEBRUIKSAANWIJZING MANUAL DEL PROPIETARIO MODE D’EMPLOI BEDIENUNGSANLEITUNG MANUALE D’ISTRUZIONI...
- Page 2 HEDGE TRIMMER GB 01-15 TAILLE HAIE FR 16-30 HECKENSCHERE DE 31-45 HEGGENSCHAAR NL 46-60 CORTASETOS ES 61-75 DECESPUGLIATORE IT 76-90...
-
Page 3: Table Of Contents
SAFETY FIRST Contents Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions 1. -
Page 4: Parts Location
1. Parts location 1. Front handle 8. Gear case 15. Blade cover 2. Rear handle 9. Starter knob 16. Operator’s manual 3. Stop switch 10. Fuel tank 17. Socket 4. Throttle trigger 11. Fuel cap 18. Allen key 5. Safety lock 12. -
Page 5: Warning Labels On The Machine
3. Warning labels on the machine If warning label peels off or becomes soiled and impossible to read, you should contact the (1)Read owner's manual before operat- dealer from which you purchased the product ing this machine. to order new labels and affix them in the required location(s). -
Page 6: For Safe Operation
5. For safe operation gases contain dangerous carbon 1. THIS MACHINE CAN CAUSE monoxide. SERIOUS INJURIES. Read this 2. Never use the product, manual carefully until you com- a. when the ground is slippery pletely understand and follow all or when you can’t maintain a safety and operating instruc- steady posture. - Page 7 When work is the engine and take the unit to to be performed simultaneously your authorized Timberpro servi- by two or more persons, care cing dealer for repair. should also be taken to constantly...
- Page 8 5. For safe operation 7. Check the cutting attachment. might result in the product be- Never use blades that are dull, coming damaged during opera- cracked or damaged. tion or the product becoming un- 8. To reduce the fire hazard, clean able to operate properly.
-
Page 9: Fuel
6. Fuel ■ FUEL ■ FUEL 6,5 Liter 6,5 Liter WARNING WARNING • Gasoline is very flammable. Avoid smoking or • Gasoline is very flammable. Avoid smoking or 7,0 Liter 7,0 Liter bringing any flame or sparks near fuel. Make sure bringing any flame or sparks near fuel. - Page 10 6. Fuel ■ FUELING THE UNIT 1. Untwist and remove the fuel cap. Rest the cap on a 17,5 Liter dustless place. 2. Put fuel into the fuel tank to 80% of the full capacity. 3. Fasten the fuel cap securely and wipe up any fuel 18,0 Liter spillage around the unit.
-
Page 11: Operation
7. Operation STARTING ENGINE 6. While holding the unit firmly, pull out the starter rope quickly until engine fires. 1. Feed fuel into the fuel tank and tighten the cap se- curely. 2. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start moving upon starting of the engine. - Page 12 Trim sides of a hedge first, and then the top. Vertical cut: • W ith the 2-sided blade model HT 260 use an arc- ing cut from the bottom upwards, then downwards to use both sides of the blades. GB 10...
-
Page 13: Maintenance
8. Maintenance Every Every Every Before System/components Procedure Note hours hours hours after after after ✔ fuel leaks, fuel spillage wipe out ✔ ✔ fuel tank, air filter, fuel filter inspect/clean replace, if necessary see adjusting replace carburetor ✔ idle adjusting screw idling speed if necessary clean and readjust... - Page 14 8. Maintenance SAFETY LOCK ANTI-VIBRATION SYSTEM WARNING WARNING • Stop operation when the safety lock is defective. The deformed or damaged anti-vibration system may cause of the breakages like getting rickety or falling • Safety lock is the device not to accelerate the throttle off of engine and/or blade .
- Page 15 8. Maintenance WAY OF THE COOLING AIR ADJUSTING CARBURETOR • This engine is air-cooled. Dust clogging between the The carburetor has been adjusted at the factory. Should inlet port of the cooling air and cylinder fins will cause your unit need readjustment due to the changes in alti- overheating of the engine.
-
Page 16: Storage
9. Storage 10. Disposal 1. Oil the blade to prevent rust. • When you dispose of the machine, do not disassemble 2. Empty the fuel tank and put the cap back on. the machine. 3. Remove the spark plug, pour a small amount of oil •... -
Page 17: Limited Warranty
OF THE COMPANY. riod, the failed part will be replaced or repaired free of THE COMPANY IS LIABLE FOR DAMAGES TO OTHER charge by a TIMBERPRO authorized dealer. ENGINE COMPONENTS CAUSED BY THE FAILURE OF A WARRANTED PART STILL UNDER WARRANTY. - Page 18 We, BVBA Tech and Trade Paalstraat 29 BE-2223 Schriek (Heist-Op-Den-Berg) - Belgium, Herewith declare under our sole responsibility that the GASOLINE HEDGE TRIMMER Model ........: HT 260 Produced under the registered trademark of Meets all relevant requirements of the above mentioned directives...
Need help?
Do you have a question about the HT 260 and is the answer not in the manual?
Questions and answers