Adjustment Instruction - LG 42PW340 Service Manual

1. Application Range
This spec. sheet applies to PU11A Chassis applied PDP TV
all models manufactured in TV factory.
2. Specification
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order. But it is
flexible when its factory local problem occurs.
(3) The adjustment must be performed in the circumstance of
25 cC ± 5 cC of temperature and 65 % ± 10 % of relative
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100 V - 240 V,
50 / 60 Hz.
(5) Before adjustment, execute Heat-Run for 5 minutes.
After Receive 100% Full white pattern (06CH) then
V
process Heat-run
(or "8. Test pattern" condition of Ez-Adjust status)
How to make set white pattern
V
1) Press Power ON button of Service Remocon
2) Press ADJ button of Service remocon. Select "10.
Test pattern" and, after select "White" using
navigation button, and then you can see 100% Full
White pattern.
* In this status you can maintain Heat-Run useless any
pattern generator
* Notice: if you maintain one picture over 20 minutes
(Especially sharp distinction black with white pattern –
13Ch, or Cross hatch pattern – 09Ch) then it can
appear image stick near black level.
3. Adjustment items
3-1. PCB Assembly adjustment
(1) Adjust 480i Comp1
(2) Adjust 1080p Comp1/RGB
- If it is necessary, it can adjustment at Manufacture Line
- You can see set adjustment status at "9. ADJUST
CHECK" of the "In-start menu"
3-2. Set Assembly Adjustment
(1) EDID (The Extended Display Identification Data )
(2) Color Temperature (White Balance) Adjustment
(3) Make sure RS-232C control
(4) Selection Factory output option
Copyright ©2011 LG Electronics Inc. All rights reserved.
Only for training and service purposes

ADJUSTMENT INSTRUCTION

4. PCB Assembly Adjustment
4-1. Using RS-232C
- Adjust 3 items at 3-1 PCB assembly adjustments
" (3) Adjustment sequence" one after the order.
(1) Adjustment protocol
Order Command
1. Inter the aa 00 00
Adjustment
mode
2. Change the XB 00 40
Source XB 00 60
3. Start ad 00 10
Adjustment
4. Return the
Response
5. Read data ( main )
Adjustment ad 00 20
data ( main )
ad 00 30
6. Confirm ad 00 99
Adjustment
7. End of ad 00 90
Adjustment
< See ADC Adjustment RS232C Protocol_Ver1.0 >
(2) Necessary items before Adjustment items
Pattern Generator : (MSPG-925FA)
O
Adjust 480i Comp1
O
(MSPG-925FA:model :209, pattern :65) – Comp1 Mode
Adjust 1080p Comp1
O
(MSPG-925FA:model :225 , pattern :65) – Comp1 Mode
Addjust RGB (MSPG-925FA:model :225 , pattern :65)
O
– RGB-PC Mode
* If you want more information then see the below Adjustment
method (Factory Adjustment)
(3) Adjustment sequence
aa 00 00: Enter the ADC Adjustment mode.
O
xb 00 40: Change the mode to Component1 (No actions)
O
ad 00 10: Adjust 480i Comp
O
ad 00 10: Adjust 1080p comp
O
xb 00 60: Change to RGB-PC mode(No action)
O
ad 00 10: Adjust 1080p RGB
O
xb 00 90: Endo of Adjustmennt
O
- 6 -
Set response
a 00 OK00x
b 00 OK40x (Adjust 480i Comp1 )
(Adjust 1080p Comp1)
b 00 OK60x (Adjust 1080p RGB)
OKx ( Success condition )
NGx ( Failed condition )
(main : component1 480i, RGB 1080p)
00000000000000000000000007c007b006dx
(main : component1 480i, RGB 1080p)
000000070000000000000000007c00830077x
NG 03 00x (Failed condition)
NG 03 01x (Failed condition)
NG 03 02x (Failed condition)
OK 03 03x (Success condition)
d 00 OK90x
LGE Internal Use Only