Fluotec VegaLux 200 HP Manual

High-Performance StudioLED FRESNEL
Specs & Performance: Daylight & Tungsten Models
11.29"
28.7 cm
Tungsten
Code: G6LED173
Code Pole Operated: G6LED182
Color Temperature: 3100K
Color Rendering Index (CRI): +93
Weight: 16.04 lb (7.28 kg)
VegaLux 200 StudioLED FRESNEL
HP
®
There are dedicated Tungsten and Daylight color models.
Fuses & Power Consumption
Note - Most electrical equipment briefly consumes a higher amount of electrical
current during startup (ignition). Consult the chart below to confirm that your
electrical wiring is sufficient for the fixtures used. All fuses must be rated at
250VAC. VegaLux 200 StudioLED FRESNEL
HP
®
MECHANICAL CHARACTERISTICS
MODEL DIMENSIONS
G6LED173
G6LED182
(Pole Operated)
VegaLux 200
® HP
Tungsten StudioLED
FRESNEL 3100K
®
11.22"x 11.29"x 18.46"
G6LED174
30.7 cm x 28.7 cm x 46.9 cm
G6LED183
(Pole Operated)
VegaLux 200
® HP
Daylight StudioLED
FRESNEL 5700K
®
90-240V
Each fixture comes with:
Barndoors - 8 Blades
G6LED121
Filter Holder
G6LED096
C-Clamp
G6FLT262
AC cord with POWERCON
Conector 16 ft (4.82 m)
G6CNT154
2 Safety Cables:
1 for barndoor
1 for fixture
G6FLT059
Stand Fitting 5/8"
G6FLT057
Motorized Zoom
®
18.46"
46.9 cm
Daylight
Code: G6LED174
Code Pole Operated: G6LED183
Color Temperature: 5700K
Color Rendering Index (CRI): +93
Weight: 16.04 lb (7.28 kg)
is not a color mixing LED system.
®
auto-set from 90-240 VAC.
®
ELECTRICAL MEASUREMENTS
WEIGHT
MAXIMUM VALUES
Voltage [V]
Power [W]
7.28 kg
16.04 lb
Current [A]
Peak Current [A]
Optional Accessories:
Pole Operated
G6LED123
Display & Buttons
Functions
The VegaLux 200
HP
®
that allow to perform various functions.
Button Function
"MENU"
Button Function
"ENTER"
Safety Cable
Holder
AC input connector
90-240 VAC
DMX input signal
connector "DMX IN"
120VAC
197
1.64
2.5
Mounting the Fixture
On Grid:
Attach clamp tightly to yoke of fixture, according to clamp mfrs.
instructions. Hang clamp on pipe or grid and tighten the large screw
so that the clamp and fixture are securely mounted. Do not loosen
bolt attaching clamp to fixture, to position light. Attach safety cable
between the fixture and the rail for necessary security.
On Stand:
Using the 5/8" female (not included) stand fitting. Choose proper size
stand for fixture. Always use sufficient stabilizing weight on stand base.
Allows mounting the fixture on 5/8" (not included) male stand stud.
Make sure the stand is large enough to support the weight of the
fixture while maintaining good balance at the desired height. Attach
the female stand-fitting tightly to the yoke and rotate yoke so it is on
the underside of the fixture. Tighten yoke, clamp locking lever, and
place female stand-fitting over stand, making sure that its locking
screw is loosened enough to allow the fitting to completely fit over
the 5/8" stand stud. Tighten knob, making sure its screw is under the
safety cut of the stand fitting stud. Add additional weight to base of
stand for increased stability.
StudioLED FRESNEL has one display, and four (4) buttons
®
Handle
AC output connector
connector "DMX OUT"
Fuse-holder
Power ON/OFF
Display
Button Function
"UP"
Button Function
"DOWN"
90-240 VAC
DMX output signal