Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for IDTECK PRG2000S
- Page 1 User’s Manual 13.56MHz [MIFARE] Contactless Smart Card User Credential Programmer...
-
Page 2: Table Of Contents
Table of Contents 1. Important Safety Instructions ..................3 2. Product Overview ......................3 3. Features .......................... 4 4. Package Contents ......................4 5. Specifications ......................... 5 6. Installation ........................5 7. Wire Colors ........................6 8. Connection to PC or SR S Series Reader ..............7 9. -
Page 3: Important Safety Instructions
The IDTECK PRG2000S is also capable of configuring the settings of SR S Series readers. The IDTECK PRG2000S can send the setting data that it used in issuing cards to an SR S Series reader so that the unit can read the card issued by the IDTECK PRG2000S. The IDTECK PRG2000S has two RS-232C communication cables, enabling communication with a PC and a SR S Series reader. -
Page 4: Features
- Operates at Supply Voltages from DC10V to DC15V 4. Package Contents Please, unpack the package and check its contents. If any of the following items is missing, contact a nearby distributor. Reader Module PRG2000S Bezel User Manual Table Holder &Screws Connector Board (1ea) -
Page 5: Specifications
6. Installation 6-1. Assembly of PRG2000S and Table Holder 1) Separate the PRG2000S bezel and the Reader Module. If necessary, use tools like a slotted screwdriver. 2) Assemble the Table Holder and Connector Board as shown on the next page. -
Page 6: Wire Colors
Figure: Assembly Diagram 6-2. Distance between PRG2000S and SR S Reader 1) When configuring a reader and issuing cards using PRG2000S connected to SR 10/30 S Reader, these two devices need to be separated from each other at least 25 cm. -
Page 7: Connection To Pc Or Sr S Series Reader
9. Operations When power is applied, the PRG2000S beeps and turns on the LEDs in the order of red > green > red > green. Then, the LEDs turn off for a while and turn on in red again, one by one, from left to right while the buzzer beeps. -
Page 8: Appendix
10. Appendix 10-1. Troubleshooting Cards won’t be recognized. Due to not using standard voltage (DC12V) or due to an incompatible card type. CAUSE 1. Confirm the standard voltage information in the User Manual or the Catalog. 2. Make sure that the card is a PHILIPS MIFARE card. >>... -
Page 9: Fcc Registration Information
11. FCC Registration Information FCC REQUIREMENTS PART 15 Caution: Any changes or modifications in construction of this device which are not expressly approved by the manufacturer for compliance could void the user's authority to operate the equipment. NOTE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions;... -
Page 10: Warranty Policy And Limitation Of Liability
4) to any losses, defects, or damages caused by lightning or other electrical discharge, natural disaster, misuse, accident or neglect. This Limited Warranty is in lieu of all other warranties, obligations, or liabilities on the part of IDTECK, and IDTECK DISCLAIMS ANY AND ALL WARRANTY, WHETHER EXPRESS OR IMPLIED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.IDTECK does not, and cannot, know... -
Page 11: How To Make Rma Request (After Sales Service)
13. How to Make RMA Request (After Sales Service) To make the RMA request, the product must be initially registered on IDTECK webpage. After registering the product, please send it to IDTECK RMA Center. Please follow the instructions below: 1. Please register the RMA request via IDTECK webpage. - Page 12 The specifications contained in this manual are subject to change without notice at any time. 5F, Ace Techno Tower B/D, 684-1, Deungchon-Dong, Gangseo-Gu, Seoul, 157-030, Korea Tel : +82-(2)-2659-0055 Fax : +82-(2)-2659-0086 E-mail : webmaster@idteck.com Aug. 2011. Copyright © IDTECK Co., Ltd.