Related Manuals for Global Fire Equipment GFE-TCP-WEB
Summary of Contents for Global Fire Equipment GFE-TCP-WEB
- Page 1 Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 GFE-TCP-WEB REMOTE ACCESS TCP/IP INTERFACE CONFIGURATION MANUAL Version 11/2017 globalfire.pt...
-
Page 2: General Description
Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 General Description GFE--TCP-WEB is a new interface for TCP/IP communication, which will bring new functionalities to JUNIOR V4, JUNO NET ORION PLUS panels. It uses our data-loop protocol and an external web-server to send and receive information from panel. In this way, supervision over individual systems via web browser can be achievable easily. -
Page 3: Connection Diagram
Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 CONFIGURATION: PANELS Introduction Interface power and communication is achieved via a 5way flat cable that's connected to a 5 pin molex connector available at panels and interface. Panel communication uses our data-loop protocol which is available differently according to the panel. - Page 4 Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 JUNIOR V4 settings Dataloop is available as default in JUNIOR V4 panel range. If necessary it can be changed in Installation Menu of panel Diagnostic mode as per below image.
-
Page 5: Configuration Interface
Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 CONFIGURATION: INTERFACE Automatic Configuration The interface is supplied with a default configuration, and it's only necessary to take the steps below: ATTENTION: This automatic process requires that DHCP is enabled in local network, which is normally activated on the router that connects to internet. - Page 6 . Interface communication is put in place via a 'serial port emulator' . We will use 'PuTTY' during next steps and it's also available in installation package. After connecting GFE-TCP-WEB to computer, check device manager to find number of COM port attributed to interface. Serie USB...
- Page 7 'Client ID' and 'CHANNEL 1' parameters are necessary during webpage configuration steps. > If you want to configure DHCP again enter the following command: wdhc = 1 and press ENTER After sucessufully completion of above steps, disconnect USB cable, connect GFE-TCP-WEB interface to desired panel and network cable.
-
Page 8: Configuration: Webpage
Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 CONFIGURATION: WEBPAGE To access the website enter the link of our server http://www.createc.pt/v2/gfe http://www.createc.pt/v1/gfe globalfire.pt... - Page 9 Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 Last step to complete configuration is to load interface and web-server parameters into webpage, press 'settings' button (left side) to hide/unhide below settings fields. SETTINGS: Installation - Installation ID name...
- Page 10 Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 DIAGNOSTICS Interface LED 2 LED 1 DESCRIPTION No Power. Connecting JUNIOR V4 In error, restart Normal state without communication Normal state, to communicate In error, locked, restart In error, locked restart...
- Page 11 Manufacturers of Fire Detection Equipment GFE-TCP-WEB - CONFIGURATION MANUAL - 11/2017 GLOBAL FIRE EQUIPMENT S.A. Sítio dos Barrabés, Armazém Nave Y, Caixa Postal 908-Z, 8150-016 São Brás de Alportel - PORTUGAL Tel: +351 289 896 560 • Sales: sales@globalfire.pt • Technical Support: techs@globalfire.pt • www.globalfire.pt...
Need help?
Do you have a question about the GFE-TCP-WEB and is the answer not in the manual?
Questions and answers