Summary of Contents for Nikcell XK3190-A26
- Page 1 XK3190-A26 Weig hing Ind icato r （Version 1.01）...
-
Page 2: Table Of Contents
Content Chapter 1 Technical Parameter Chapter 2 Installation ………………………………………………… 2 eighing indicator front side function instruction and back side function instruction. (1)W Load cell & weighing indicator connection Chapter 3 Operation Instruction…………………………………… 4 (1). Button function (2). Startup&Shut down (3). Battery use (4). -
Page 3: Chapter 1 Technical Parameter
X K 3 1 9 0 –A26 Chapter 1 Technical Parameter 1. Model : XK3190-A26 2. Accuracy class : , n=3000 Class 3. A/D conversion mode: ∑-Δ 4. A/D conversion resolution： 1 million yard 5. A/D conversion speed： 10 times/second 6. -
Page 4: Chapter 2 Installation
X K 3 1 9 0 –A26 Chapter2 Installation & Connection 1. A26 weighing indicator front side function instruction and back side function instruction. : Load cell Front side function instruction (2-1-1 ) Fuse or extension interface ack side function instruction (2-1-2 )B... - Page 5 X K 3 1 9 0 –A26 2. Load cell and weighing indicator connection : A26 adopts 5 pin plug connect with sensor, and definition are as follows:： Foot definition position Excitation voltage + （E+） Excitation voltage - （E-） Signal+（S+） Signal-（S-）...
-
Page 6: Chapter 3 Operation Instruction
X K 3 1 9 0 –A26 Chapter 3 Operation Instruction 1.. Button function： 1.“0~9”number button Weighing state： unit price input State setting：parameter input 2.“Accu”button Amount is zero：accumulation display Amount is not zero：accumulation function State setting：Exit button 3.“Clear”button When there is accumulation：Clear accumulation When there is no accumulation：Clear unit price State setting：Confirm button 4.“Tare”button... -
Page 7: Battery Use
X K 3 1 9 0 –A26 Press“on/off tartup&shut down”button for 2~3 seconds in weighing state,then the indicator will shut down. Battery use (1)Battery charge Indicator is turned off, connect the AC power (AC indication light is on), began to charge the battery , the charging time is about 20 to 30 hours. -
Page 8: Unit Price Input
X K 3 1 9 0 –A26 5. Tare operation (1) .Tare In weighing state and if the gross weight is above zero and in stable state press"tare"button and delete the current gross weight as tare weight, and display the net weight is zero and tare indicate symbol light will on. -
Page 9: Saving And Re-Call Of Unit Price
X K 3 1 9 0 –A26 】 （Accumulate display reminder， press any key to back Indicator display【totAL into the weighing state） 【 ** 】 （Accumulate times） 【 ***.** 】 （Accumulate amount） (3). Accumulate clear When indicator accumulate calculate （ accumulate indicate symbol light is on） ， press “ clear” button can clear accumulate amount and accumulate times to zero，accumulate calculate indicate symbol is off. -
Page 10: Inner Code Display
X K 3 1 9 0 –A26 】 （Power saving reminder） Indicator display【bL 【 * 】 （Original power saving mode） Now after input the new power saving mode parameter （ 0~4),press “ clear” confirm， then press“Accu”back to weighing state. (3)The meaning of power saving mode parameter bL = 0：... -
Page 11: Chapter4 Optional Function
X K 3 1 9 0 –A26 Chapter4 Optional function 1.RS232 communication. (1)Brief introduction RS232 has 4 kinds of serial communication format of A26（see chapter4），and there are 4 kinds of baud rate can be set. All the data are ASCII code，each group consists of 10 bits data, 1 start bit, 8 data bits, 1 stop bit. - Page 12 X K 3 1 9 0 –A26 ④ Indicator display【bAUd 】 （chose communication baud rate chose） 【 * 】 （1200、2400、4800、9600） After input the baud rate required,press"clear"button confirm and finish the communication parameter setting and back to weighing state. In the parameter input process, press the "Accu"button, you can terminate the parameter input, back to weighing mode.
- Page 13 X K 3 1 9 0 –A26 ： ： Weighing data Weighing data high position symbol position 0 or - For example the current display weight is 3.000，so the sending data is： ＝000.3000＝000.3000＝000.3000＝000.3000 For example the current display weight is -1.00，so the sending data is: ＝00.1000－＝00.1000－＝00.1000－＝00.1000－...
-
Page 14: Serial Port Print
X K 3 1 9 0 –A26 Unit price lower position ； separator Amount（including decimal point） higher position ： ： Amount Amount lower position For example the current display weight is2.000，unit price is 1.00, amount is 2.00 ,so the sending data is: ＝0002.000;001.00;0002.00;... -
Page 15: Scoreboard Output
X K 3 1 9 0 –A26 ③ Indicator display【Prnt 】 （print content selection） 【 ***** 】 （only can input 0 or 1 ） there are 5 digits from right to left, they are stand for： The 1 digit： 0：not print SN number； 1：print SN number The 2 digit：... -
Page 16: Upper And Lower Limits Alarming
X K 3 1 9 0 –A26 scoreboard connect line(blue line)； Foot 5 of the plug on the back of the indicator is GND,connect with the scoreboard connect line(black line). (3)Parameter setting ① Press"1"and "Clear"button in same time in weighing state. 】... - Page 17 X K 3 1 9 0 –A26 ① Press"1"and "Clear"button in same time in weighing state. 】 （Power-saving mode chosen） Indicator display【bL 【 * 】 Press“clear”enter into next optional function chosen. ② Indicator display【Func 】 （optional function chose） 【 】 （0~4） Now input“4”and choose upper and lower limit alarming optional function and press "clear"...
- Page 18 X K 3 1 9 0 –A26 Parameters : FunC =4；ctrL=34; PP1=1.900; PP2=2.100。 Now put the switch volume 1 and 2 together as hardware to be an output. Chapter5 Information Indication Err 03 ： Overload alarming, need remove parts of the load or all of the load. Err 05 ：...
-
Page 19: Chapter 6 Maintenance And Attention
X K 3 1 9 0 –A26 Chapter 6 Maintenance and attention 1.To guarantee its clarity and service life, the indicator shouldn’t be placed directly under sunshine and should be set in the plain space. 2.It is not suitable to place the indicator in the dusty and vibration environment and also avoid using in the moist environment. - Page 20 X K 3 1 9 0 –A26 every time 20 to 25 hours. (Note：Charging time is around 20-25 hours and the indicator must be power off) When moving or installing the indicator, you must carefully move it and avoid ▲！ strong vibration, impact or bump in order to avoid electrode in the battery being shorted and damaged 10.