Antunes JS-1000 International Owner’s Manual

Jet steamer

Advertisement

Quick Links

Jet Steamer
JS-1000
International Owner's Manual
Manufacturing Number:
9100672
IPX
Rating
Original Instructions
P/N 1011512 Rev A 10/18
CAUTION: Read the instructions before using the machine
www.antunes.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the JS-1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for Antunes JS-1000

  • Page 1 Jet Steamer JS-1000 International Owner’s Manual Manufacturing Number: 9100672 Rating Original Instructions P/N 1011512 Rev A 10/18 CAUTION: Read the instructions before using the machine www.antunes.com...
  • Page 2: Table Of Contents

    If any parts are missing or damaged, ies, butcheries, etc., But not for continuous Service/Technical Assistance problems with the installation or operation mass production of food. of this product contact Antunes Customer In Case of Damage Service immediately at +1-877-392-7856 Equipment Information to Save (toll free).
  • Page 3: Safety Information

    Officials and Code Administrators, performed by qualified personnel Inc. (BOCA) and the Food Service y Do not block or cover any ONLY. Contact Antunes Technical Sanitation Manual of the Food openings on the equipment. Service for adjustment or repair. and Drug Administration (FDA).
  • Page 4: Specifications

    Specifications Electrical Ratings Plug Mfg. No. Volts Watts Amps Hertz Plug Configuration Description HRMN/IEC-309 9100672 208-240 3800 (P/N 0700588) Assembly Only Model # (A) Width (B) Depth (C) Height 12.5” 20.75” 20” 9100672 (318mm) (527mm) (508mm) P/N 1011512 Rev A 10/18...
  • Page 5: Installation

    Open the large box. Remove all packing materials and protective coverings from the unit and parts. NOTICE: If any parts are missing or damaged, contact Antunes Customer Service IMMEDI- ATELY at +1-877-392-7856 (toll free). Place the unit where it will be used.
  • Page 6: Pressure Regulator Setup

    Nipple, 1/4 NPT X 1/4” NPT nect Insert until a good, steady water Water Pressure Gauge (0- flow is noted (this will purge all air out The JS-1000 requires a direct cold water of the line). hookup. Incoming water is controlled by Pressure Regulator...
  • Page 7: Operating Instructions

    Operating Instructions If required, you can press the Pause icon REMINDER to pause the cooking cycle. Press the Resume icon to continue cooking. If Spray the cup and nozzle with a non- you need to cancel a cooking cycle, stick spray before every use. press the Cancel icon .
  • Page 8: Working With Menu Items

    Creating New Menu Items After you touch the item you wish to edit, Working with Menu Items the system displays the name of the item Creating new menu items follows the same and an on-screen keyboard you can use Follow these steps to create new menu procedure as editing an existing menu to rename the item.
  • Page 9: System Settings

    System Settings Loading Menu Data via 4. From this screen you can change the Follow these steps to access and edit the following system settings: system settings. USB connector y Degrees: F/C From the Heating or Ready screen, y Beep (sounds when cooking press the Tools icon cycle completes).
  • Page 10: Maintenance

    Maintenance NOTICE: Frequency of cleaning is Hose connection manifold determined by water conditions, usage, and water filter systems Cup mounting platform Recommended water hardness, or Total Dissolved Solids (TDS), Steam nozzle should not exceed 60 ppm (parts per million). Daily Cleaning NOTICE: Clean the cup and nozzle after every use.
  • Page 11: Quarterly Cleaning

    Quarterly Cleaning Checking and Cleaning Water NOTICE: Be sure to follow the delimer manufacturer’s directions for Strainer This unit utilizes an open steam genera- proper mixture and use. tor. When introduced, water immediately To ensure proper and consistent steam- Remove the delimer solution from vaporizes creating a burst of steam, ing results, inspect the water pressure the generator and rinse with clear...
  • Page 12: Troubleshooting

    TROUBLESHOOTING Problem Possible Cause Corrective Action Power cord not correctly plugged in Plug in the power cord correctly. The power cord and/or electrical plug is Unit displays system error: Inspect electrical wire, plug, and receptacle. damaged “Zero Cross” Control board is inoperable Contact your maintenance person or Authorized Service Agency for service.
  • Page 13: Wiring Diagram

    WIRING DIAGRAM P/N 1011512 Rev A 10/18...
  • Page 14: Replacement Parts

    Gasket retainer 0400290 Electrical insulator NOTICE 1002730 Wiring diagram label Use only genuine Antunes replacement parts in this unit. Use 0507960 Rear panel of parts other than those supplied by the manufacturer will void Nut, hex “KEPS” #06-32 steel; the warranty.
  • Page 15 Part # Description 7001629 Knob kit 7001630 Plunger Assy kit 7001631 Male to Barb Elbow kit 7001632 Male to Male Elbow kit 7001633 Generator kit 7001634 Vane Micro Switch kit 7001635 Vane Switch Lever kit 7001636 Front Housing Micro Switch kit 7001637 PCB-Assy Switch Board kit 7001638...
  • Page 16 41 7× 81 47 P/N 1011512 Rev A 10/18...
  • Page 17: Notes

    Notes P/N 1011512 Rev A 10/18...
  • Page 18: Limited Warranty

    The remedies described above are exclusive and in no event shall Antunes be liable for special consequential or incidental damages for the breach or delay in performance of this warranty.

Table of Contents