Subscribe to Our Youtube Channel
Related Manuals for DeltaOHM HD2016
Summary of Contents for DeltaOHM HD2016
- Page 1 English Operating manual Weighing rain gauge HD2016 Companies / Brands of GHM www.deltaohm.com Keep for future reference.
-
Page 2: Table Of Contents
NOTES ON WEIGHT MEASUREMENTS ..............23 STATUS REGISTER ....................23 MAINTENANCE....................24 TECHNICAL CHARACTERISTICS ................27 INSTRUMENT STORAGE ..................27 SAFETY INSTRUCTIONS..................28 ORDERING CODES ....................29 HD2016 V1.4... -
Page 3: Introduction
1 INTRODUCTION HD2016 is a rain gauge that detects the weight of the rainfall collected by a 400 cm inlet. The sensor is a load cell located at the base of the rainfall collecting reservoir. The signal of the load cell is processed by the internal electronic board of the rain gauge in order to output the information on the rainfall. -
Page 4: Description
2 DESCRIPTION HD2016 V1.4... - Page 5 11. Optional cable for the connection of the measuring circuit power supply and signals. 12. Cable gland for the heater power supply. 13. Port reserved for technical service. 14. Screws for fixing the cylindrical cover. 15. Cylindrical cover. HD2016 V1.4...
-
Page 6: Installation
Not connected pole of the voltage-free contact Fig. 3.1.1: M12 connector and CP18… cable Connect the Protective Earth via the terminal under the base of the rain gauge (point 9 on page 4). HD2016 V1.4... -
Page 7: Choosing The Digital Output And The Protocol
SW1), or set the switch toward the ASCII indication to select the ASCII proprietary protocol. If the standard protocol is selected, it is possible to switch to the ASCII proprietary protocol while the instrument is operating as described in the paragraph HD2016 V1.4... -
Page 8: Rs485 Connection
Each instrument on the network is univocally identified by an address. Multiple transmitters with the same address should not be placed in the network. Before connecting the in- strument to the network, set the address and, if necessary, the communication parameters. HD2016 V1.4... -
Page 9: Sdi-12 Connection
Each pulse corresponds to an amount of rainfall configurable from 0.001 to 1 mm/pulse (default=0.2) by using the command CP0 of the ASCII proprietary protocol. Data logger input contact 1 pole CP18… cable contact 2 pole Power supply Fig. 3.5.1 – contact output connection HD2016 V1.4... -
Page 10: Unlocking The Load Cell
For ground installation, secure the three support feet to the base of the instrument. Adjust the height of the feet so that the instrument is perfectly levelled. The instrument can be fixed to the floor by using the holes provided in the feet, close to the adjustment screws. - 10 HD2016 V1.4... - Page 11 Fig. 3.7.2: rain gauge ground installation For raised installation, secure the flange of the HD2016.33K kit to the base of the instrument and screw the support rod to the flange; the rod may end with a flange (HD2003.78) to fixed to the floor.
-
Page 12: Ascii Proprietary Protocol
CAL USER ON, send the command CAL END (the instrument replies with address: LOCKED). The command CAL USER ON is automatically disabled after 5 minutes of inactivity. If the set- tings should be only read, the command CAL USER ON is not required. - 12 HD2016 V1.4... - Page 13 Instrument general information Command Reply Description address: & Ping HD2016 Model SN=number Serial number Firm. Ver.=version Firmware version Firm. Date=yyyy/mm/dd Firmware date F cal:yyyy/mm/dd hh:mm:ss Factory calibration date Reservoir discharge Command Reply Description address: & Runs the reservoir discharge cycle address: state&...
- Page 14 MB baud Reads the Modbus Baud Rate: Baud rate index=0 ⇒ 9600 Baud rate index=1 ⇒ 19200 (default) CMB n address: & Sets the Modbus Baud Rate of index n: n=0 ⇒ 9600 ; n=1 ⇒ 19200 - 14 HD2016 V1.4...
- Page 15 For details on weight measurements, please see the paragraph “Notes on weight measurements”. RR n address: measured value Continuous print (once per second) of the measure of index n (see the command SR for the indexes) - 15 HD2016 V1.4...
- Page 16 (see the command S0 for the fields) address: & voltage status_register Prints the supply voltage in Volt and the content of the status register in hexadecimal address: status_register Prints the content of the status register in hexadeci- - 16 HD2016 V1.4...
-
Page 17: Modbus-Rtu Protocol
Some operating parameters of the instrument can be changed directly with Modbus commands by setting the value of the Holding Registers with the function code 06h (Write Single Register) or 10h (Write Multiple Registers). The following table lists the Holding Registers available. - 17 HD2016 V1.4... - Page 18 Permanent storage of the parameters. In order to check whether the permanent storage has been completed successfully, verify that the Holding Register with address 1 contains 0, by using the function 03h (Read Holding Regis- ters). - 18 HD2016 V1.4...
-
Page 19: Sdi-12 Protocol
= serial number (8 characters) ⇒ Example of reply: 013DeltaOhmHD2016A0013201518 with: 0 = instrument address 13 = SDI-12 version 1.3 compliant DeltaOhm = manufacturer’s name HD2016 = instrument model A00 = firmware version 13201518 = serial number aAb! b<CR><LF> Modification of the instrument address. - Page 20 - rainfall rate = partial rainfall, in mm, from the last reset command - temperature (°C) = average rainfall rate, in mm/min, calculated in the last minute T = rain gauge internal temperature in °C - 20 HD2016 V1.4...
- Page 21 Pmg = rainfall total weight in mg Wmg = rainfall total weight, in mg, considering the eva- poration Tmg = weight, in mg, of the current reservoir content For details on weight measurements, please see the paragraph “Notes on weight measurements”. - 21 HD2016 V1.4...
- Page 22 To change the rain gauge parameters, the command aXSCAL USER ON! must be sent first (the instrument replies USER ENABLED). To cancel the command CAL USER ON, send the command aXSCAL END! (the instrument replies LOCKED). For more information about the SDI-12 protocol, visit the website "www.sdi-12.org". - 22 HD2016 V1.4...
-
Page 23: Notes On Weight Measurements
Rainfall state (0=no raining, 1=currently raining) Emptying rainfall reservoir Invalid data To ensure the reliability of the measured values, it is recommended to periodically check the content of the status register (especially the bits 0 and 15). - 23 HD2016 V1.4... -
Page 24: Maintenance
To clean the water drain, open the dis- charge valve by using the serial command CVL of the ASCII proprietary protocol (see chapter - 24 HD2016 V1.4... - Page 25 5. Pour water in the rain gauge continuously until the water begins to flow out from the over- flow drain. 6. To empty the rainfall collecting reservoir, open the discharge valve by using the serial command CVL. - 25 HD2016 V1.4...
- Page 26 1. By sending the command CLR of the ASCII proprietary protocol. 2. By writing A55Ah in the Holding Register with address 9 of the Modbus-RTU protocol. 3. By sending the extended command aXSCLR! (a is the instrument address) of the SDI-12 pro- tocol. - 26 HD2016 V1.4...
-
Page 27: Technical Characteristics
(AWG 13, only HD2016R) (*) Very light rainfalls (less than about 10 g, corresponding to approx. 0.2 mm) are not detected because the water stagnates in the valves and filters, and does not reach the collecting reservoir. - 27 HD2016 V1.4... -
Page 28: Instrument Storage
User obligations The instrument operator shall follow the directives and regulations below that refer to the treatment of dangerous materials: • EEC directives on workplace safety. • National law regulations on workplace safety. • Accident prevention regulations. - 28 HD2016 V1.4... -
Page 29: Ordering Codes
13 ORDERING CODES HD2016 Weighing rain gauge, area 400 cm , Operating temperature from +4 °C to +60 °C. RS485 Modbus-RTU or SDI-12 output. Voltage-free contact (NO) output. Power supply: 10…15 Vdc. Adjustable feet for ground installation in- cluded. HD2016R Weighing rain gauge, area 400 cm , with heater. - Page 30 OTES - 30 HD2016 V1.4...
- Page 32 This guarantee must be sent together with the instrument to our service centre. IMPORTANT: Guarantee is valid only if coupon has been correctly filled in all details. HD2016 HD2016R Instrument Code:...
- Page 33 Via Marconi 5 | 35030 Caselle di Selvazzano | Padova | ITALY Phone +39 049 8977150 | Fax +39 049 635596 www.deltaohm.com | info@deltaohm.com The quality level of our instruments is the result of the constant development of the product. This may produce some differences between the information written in this manual and the instrument you have purchased.
- Page 34 GHM GROUP – Delta OHM | Delta Ohm S.r.l. a socio unico Via Marconi 5 | 35030 Caselle di Selvazzano | Padova | ITALY Phone +39 049 8977150 | Fax +39 049 635596 www.deltaohm.com | info@deltaohm.com V1.4 08/01/2019...
Need help?
Do you have a question about the HD2016 and is the answer not in the manual?
Questions and answers