Subscribe to Our Youtube Channel
Related Manuals for DVS SDStationOEM
Summary of Contents for DVS SDStationOEM
- Page 1 PCI Video Board Home/Start SDStationOEM DMediaPro DM6 for SGI Systems Installation Guide...
- Page 3 SDStationOEM Installation Guide Introduction Overview Installation Appendix Index...
- Page 4 The software, hardware and manuals described here and all their constituent parts are protected by copyright. Without the express permission of DVS GmbH Digitale Videosysteme any form of use which goes beyond the narrow bounds prescribed by copyright legislation is prohibited and liable to prosecution.
- Page 5 Headquarter: DVS GmbH Digitale Videosysteme Krepenstr. 8 D-30165 Hannover GERMANY Phone: +49-511-67807-0 Fax: +49-511-630070 E-mail: info@dvs.de Internet: http://www.dvs.de Support: Phone: +49-511-67807-25 Fax: +49-511-67807-31 E-mail: support@dvs.de For the Americas: U.S. Headquarters: East Coast Office: DVS Digital Video, Inc. DVS Digital Video, Inc.
- Page 6 For systems purchased from SGI: For product support information, contact your SGI subsidiary or authorized distrib- utor. SGI provides a comprehensive range of product support for its products. If you are in North America, contact the Technical Assistance Center at +1 800 800 4SGI or your authorized service provider.
- Page 7 You may also use our online registration form which can be accessed from the following internet page: http://www.dvs.de/english/ support/support.html If you purchased the SDStationOEM / DMediaPro DM6 from SGI, a sending of this form is not necessary because SGI offers its own support for this product. Customer...
-
Page 9: Table Of Contents
Contents Introduction ................1-1 1.1 Overview................1-2 1.2 Target Group................ 1-2 1.3 Conventions Used in this User Guide........1-3 1.4 Safety Instructions ............... 1-4 1.5 Important Notes ..............1-5 1.6 Scope of Delivery ..............1-7 1.7 System Requirements ............1-9 Overview ................... - Page 10 SDStationOEM Installation Guide Appendix ...................A-1 A.1 Technical Data ..............A-1 A.2 Hardware Specifications ............A-2 A.3 Video Raster ................A-3 A.4 Conformity Declarations ............A-4 Index .................... I-1...
-
Page 11: Introduction
Introduction This documentation describes the SDStationOEM which is DVS’ OEM product of the SDStationPRO family. The SDStationOEM is centered around the SDStationBoard, a half-length PCI-bus single board for real-time input and output of uncompressed SDTV signals. With the SDStationBoard a computer can handle 8 and 10 bit digital serial SDTV streams. -
Page 12: Overview
SDStationOEM Installation Guide Overview This guide informs you about the installation of the SDStationOEM as well as all connection possibilities. Furthermore, it provides informa- tion about the installation of the delivered drivers and software. The chapters contain the following information:... -
Page 13: Conventions Used In This User Guide
Introduction Conventions Used in this User Guide The following typographical conventions will be used in this docu- mentation: – Texts preceded by this symbol are parts of a list. Texts preceded by this symbol are also parts of a list, i.e. lists of a second level. -
Page 14: Safety Instructions
– Use the SDStationOEM only in apparent good technical order. – The system you are trying to connect the SDStationOEM to usu- ally work with voltages that can be hazardous to your health. Never access its interior with the power cable(s) being plugged in. -
Page 15: Important Notes
Warranty Information This product is warranted to be free of defects in materials and work- manship for a period of one year from the date of purchase. DVS ex- tends this Limited Warranty to the original purchaser. In the event of a defect or failure to confirm to this Limited Warranty, DVS will repair or replace the product without charge. - Page 16 SDStationOEM Installation Guide Declarations of Conformity This product was tested according to the applying direc- tives and regulations of the EC and the FCC. Further in- formation on this can be found in section “Conformity Declarations” on page A-4. Unplugging Cables...
-
Page 17: Scope Of Delivery
Introduction Scope of Delivery The following lists the items that come with the SDStationOEM. As well, it provides an overview of the optionally available features for the SDStationOEM and the items that are delivered with this feature: Expansion and optional panels are not supported in DMediaPro DM6 systems. - Page 18 SDStationOEM Installation Guide Option: SSO-GPI – 1 × Slot panel ‘GPI/WCLK’ 2 × MCX-to-BNC cables (for internal connection, already mounted on slot panel) 1 × 12-pin flat cable (for internal connection) Option: SSO-256MB – 256 Mbytes of on-board RAM instead of 32 Mbytes License Key for Options needed for SSO-Audio4, SSO-Key and/or SSO-RGBA;...
-
Page 19: System Requirements
Required Hardware These are the minimum hardware requirements that the computer system has to meet if you want to use the SDStationOEM. – Mainboard with 64 bit, 33 or 66 MHz PCI bus The SDStationOEM operates with 33 MHz. It can be plugged in a 66 MHz PCI slot but will force the PCI bus fre- quency to operate overall with 33 MHz. - Page 20 SDStationOEM Installation Guide 1-10...
-
Page 21: Overview
Overview This chapter shows an overview of the SDStationOEM. It details all connectors and interfaces of the SDStationBoard and its additional panels. Furthermore, for the installation (described in chapter “Instal- lation” on page 3-1) the panel drawings already show both the exter- nal connectors as well as the internal connections between panels and board. -
Page 22: Sdstationboard Layout
SDStationOEM Installation Guide 2.1.1 SDStationBoard Layout The following figure details the layout of the SDStationBoard: Figure 2-1: Overview of SDStationOEM... -
Page 23: Digital Video I/O
2.1.2 Digital Video I/O Please note that this section describes the single-link and the optionally available dual-link capability of the SDStationOEM. The digital video I/Os have dual-link capabilities. Thus each I/O con- sists of two ports labelled ’A’ and ’B’. In YC... -
Page 24: Leds
A wrong input signal is detected (e.g. the fast SDStationOEM is set to NTSC video mode, but a PAL signal is connected to the active input). A correct input signal is detected. green Signals the status A correct sync signal is detected, i.e.:... -
Page 25: Overview Of Panels
This section should serve as an overview of the different panels as well as an installation instruction how to connect the SDStationOEM with the additional panels: the panel drawings already show both the external connectors as well as the internal connections between pan- els and board. -
Page 26: Analog Audio & Video Panel
SDStationOEM Installation Guide 2.2.1 Analog Audio & Video Panel The following panel comes with the basic configuration of the SDStationOEM and shows the connectors needed for monitoring au- dio and video. Analog Audio Out (Ch. 1 & 2) Audio Analog Audio Out (Ch. 3 & 4) -
Page 27: Rs-422 Panels
Overview 2.2.2 RS-422 Panels The RMT1 panel is included in the basic configuration of the SDStationOEM. The RMT2 panel is currently in its development stage and will be available as an optional feature for the SDStationOEM. The RS-422 panels hold the interfaces for master and slave control as well as the main (A) ports of SDI input 2 and SDI output 2. -
Page 28: Serial Digital Interface (Sdi) Panel
SDStationOEM Installation Guide 2.2.3 Serial Digital Interface (SDI) Panel The SDI panel is optionally available and holds some of the SDI in- puts and outputs, i.e. the digital video I/Os. The other SDI connectors can be found on the SDStationBoard panel and the RS-422 panels. -
Page 29: Aes/Ebu Audio Panel
Overview 2.2.4 AES/EBU Audio Panel The AES/EBU audio panel is optionally available and holds the in- puts/outputs for digital audio and LTC. CH 5–8 AES/EBU Audio I/O (Ch. 5–8) CH 1–4 LTC AES/EBU Audio I/O (Ch. 1–4), LTC I/O AUDIO Figure 2-5: Audio panel... -
Page 30: Gpi & Audio Wordclock Panel
GPI for their correct settings. If they are not set correctly, using this interface may result in an unexpected behavior of the SDStationOEM. The jumpers should be set like shown in the figure below:... - Page 31 Overview The power line to be connected to the printed board of the GPI has to be a standard power distribution line of your computer system. It should be of the same type as, for example, used to power your flop- py, i.e.
- Page 32 SDStationOEM Installation Guide 2-12...
-
Page 33: Installation
Installation This chapter details all the information you need to install the SDStationOEM into a computer system. First, the installation of the board itself is described. After that follows a description of the software installation. -
Page 34: Hardware Installation
SDStationOEM Installation Guide Hardware Installation How to install the SDStationOEM in a computer system is described in this section. The installation can be performed in three steps: At first, you have to prepare the computer system where the SDStationBoard has to be installed. After that the board itself must be installed and in the last step the installation can be finished. - Page 35 Installation Installation of the Board With the second step the SDStationOEM is installed in the prepared computer system. To do this perform the following: In the computer system find a free half-length PCI slot. Remove the slot bracket of this slot.
-
Page 36: Software Installation
The installation of the SGI Package is performed with three different distribution files. They contain all the software and drivers you need to control the SDStationOEM. Once all three files are installed and the system has restarted, the installation will be complete. Below you find... - Page 37 Installation Figure 3-1: The main window of the Software Manager On the File menu select the menu option Open Distribution... to open the standard ’Open’ dialog window. Change to the directory where the SGI software package is stored. Select the file ml from the SGI directory and confirm your selec- tion with the button OK.
-
Page 38: Testing The Installation
Select the radio button ’Restart the system now’ and confirm this by clicking the button OK. Once the system has restarted, the installation is finished. To find out if your SDStationOEM works properly, you may perform a brief test on the installation. Testing the Installation After having installed the software package, you should test if the SDStationOEM installation has been successful. -
Page 39: Appendix
-17°C (0°F) to 70°C (158°F) mental conditions 10% to 80% relative humidity, non-condensing The SDStationOEM operates with 33 MHz. It can be plugged in a 66 MHz PCI slot but will force the PCI bus frequency to operate overall with 33 MHz. -
Page 40: Hardware Specifications
SDStationOEM Installation Guide A.2 Hardware Specifications The following table shows the hardware specifications of the SDStationBoard. Table A-1:SDStationBoard specifications Video Input Output Serial Digital 4:2:2 8/10 bit 1 BNC (a 1 BNC (c 1 BNC (a 1 BNC (c switchable, plus... -
Page 41: Video Raster
Internal Processing Color space conversion A.3 Video Raster The following table shows the supported video raster. All frequencies indicate the frame rate. Table A-2:Supported video raster Name in DVS Total lines Aspect Raster x size y size software per frame ratio NTSC / 29.97 Hz... -
Page 42: Conformity Declarations
SDStationOEM Installation Guide A.4 Conformity Declarations EC Declaration of Conformity EG-Konformitätserklärung DVS GmbH Digitale Videosysteme Krepenstr. 8 Wir: 30165 Hannover Germany declare herewith, that the following product: Erklären hiermit, dass folgendes Produkt: product designation: SDStationOEM Produktbezeichnung: type: SDStationV2 Typ: according to the provisions of the following EC Directives – including their relevant re- visions at the time of this declaration –... - Page 43 Appendix FCC Compliance Statement Information DVS GmbH Digitale Videosysteme Krepenstr. 8 30165 Hannover Germany declare herewith, that the following product: product designation: SDStationOEM type: SDStationV2 has been tested according to the applying valid FCC regulations. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digi- tal device, pursuant to Part 15 of the FCC Rules.
- Page 44 SDStationOEM Installation Guide...
-
Page 45: Index
..... 1-3 conventions (typographical) ........... 3-4, 3-5 ....1-6 declaration of conformity ......3-4, 3-6 ml_alaudio ....1-7 delivery of SDStationOEM ......3-4, 3-6 ml_sddigvid ...... 2-3, 2-8 digital video I/Os ......... 3-6 mlquery ......3-4 distribution files ........ - Page 46 SDStationOEM Installation Guide ........2-3 single link ......3-4 software installation panel ......3-4 Software Manager ......2-9 AES/EBU audio ..A-2 specifications of SDStationBoard ....2-6 analog audio & video ........2-4 sync signal ....2-10 GPI & audio WCLK .......
Need help?
Do you have a question about the SDStationOEM and is the answer not in the manual?
Questions and answers