Subscribe to Our Youtube Channel
Related Manuals for MicroAir Avionics T2000UAV-L
Summary of Contents for MicroAir Avionics T2000UAV-L
- Page 1 Microair Avionics Pty Ltd Airport Drive Bundaberg Queensland 4670 Australia Tel: +61 7 41 553048 Fax: +61 7 41 553049 e-mail: sales@microair.com.au...
- Page 2 T2000 transponder series. © Microair Avionics Pty Ltd REVISION STATUS Revision Date Change 01R1 28/07/09 Initial release The T2000UAV-L Transponder is not a TSO’d product. T2000UAV-L Installation and User Manual 01R1.doc Page 2 of 24 July 2009...
-
Page 3: Table Of Contents
ANTENNA COAXIAL CABLE WIRING CABLING POWER ON/OFF SUPPRESSION IN / OUT EXTERNAL STANDBY EXTERNAL IDENT TECHNICAL DRAWINGS 10.0 WIRING DIAGRAMS 11.0 PIN ASSIGNMENTS 12.0 SPECIFICATIONS 13.0 LIMITED WARRANTY T2000UAV-L Installation and User Manual 01R1.doc Page 3 of 24 July 2009... -
Page 4: Introduction
Install and User Manual INTRODUCTION The T2000UAV-L is a special version of the T2000 Transponder, designed for operation in unmanned aircraft. This product is not TSO’d due to the OEM nature of the management software. The system consisting of the T2000UAV-L, and the OEM’s management software control should collectively be submitted for compliance to... -
Page 5: T2000Uav-L Description
The T2000UAV-L requires a standard Gillham code altitude encoder, to supply altitude data over a 10 line parallel interface. The T2000UAV-L features remote switching options, available from the rear DB-25 connector for remote standby and remote ident functions. T2000UAV-L ANTENNA OPTIONS The T2000UAV-L can be supplied with a standard BNC connector located on the rear face of the chassis, adjacent to the DB-25. -
Page 6: Software Control
Install and User Manual SOFTWARE CONTROL The T2000UAV-L can be controlled by issuing of commands in the form of ASCII characters, sent and received over an RS232 interface. The command set can be used to either poll the transponder of the status of a parameter, or to command a function to a particular setting. -
Page 7: The Uav Command Structure
THE UAV COMMAND STRUCTURE The T2000UAV-L is controlled by a series of simple commands. The T2000UAV-L can be commanded to set a code, and to operate in a particular mode. Once the code is set, and the operating mode decided, the T2000UAV-L will operate until another command is received. -
Page 8: Serial Data Command Set
(set bus voltage to 14V) v=13.6 (write successful, current voltage returned) (Read/Write) v=2 (set bus voltage to 28V) v=24.8 (write successful, current voltage returned) Software Revision z=<current software revision> eg T2000U xx-x.x.x T2000UAV-L Installation and User Manual 01R1.doc Page 8 of 24 July 2009... -
Page 9: Standby (S=T)
The ident function is performed at the request of ATC to “squawk ident”. To initiate the ident function the “i” parameter is set to s. The T2000UAV-L will switch to ident mode, which will add an additional data bit to the outgoing replies. -
Page 10: Encoder Power (E=?)
The equivalent function for the T2000UAV-L is the “r” command which activates the reply annunciator. When activated (r=y), the T2000UAV-L will send a single * character, if there was a reply made in the preceding 3.6 seconds. When not activated (r=n), no character is sent. -
Page 11: T2000Uav-L Tie Down Strap
Although it is unlikely that the encoder source in a UAV installation will require switched power from the T2000UAV-L, it is recommended that the ground be wired with the data lines in all cases. This will ensure correct signal operation of the Gillham code. -
Page 12: Antenna
7.0 COAXIAL CABLE The T2000UAV-L allows for 1.5dB cable loss from the unit to the antenna. The installer should consider carefully what type of coaxial cable is to be used, so that this loss limit is not exceeded. The cable should be terminated with silver plated BNC connectors where possible. -
Page 13: Wiring
CABLING Microair recommends that wiring for all of the T2000UAV-L’s functions and connections be run at the time of installation, even though they may not be required at this stage. Adding additional wiring to the loom at a later stage may be very difficult. -
Page 14: Power On/Off
There is no software OFF command. When power is removed from the T2000UAV-L, it will not respond to any software command. When the T2000UAV-L is turned on, it is always in standby mode. The mode A code will default to the last mode A code used. -
Page 15: Technical Drawings
Microair Avionics T2000UAV-L Install and User Manual TECHNICAL DRAWINGS T2000UAV-L Installation and User Manual 01R1.doc Page 15 of 24 July 2009... -
Page 16: Install And User Manual
Microair Avionics T2000UAV-L Install and User Manual T2000UAV-L Installation and User Manual 01R1.doc Page 16 of 24 July 2009... -
Page 17: Wiring Diagrams
Install and User Manual 10.0 WIRING DIAGRAMS T2000UAV-L with EC2002 Altitude Encoder T2000UAV-L with AK-350 Altitude Encoder T2000UAV-L with A-30 Altitude Encoder T2000UAV-L with serial altitude data interface T2000UAV-L Installation and User Manual 01R1.doc Page 17 of 24 July 2009... - Page 18 Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH EC2002 ALTITUDE ENCODER T2000UAV-L Installation and User Manual 01R1.doc Page 18 of 24 July 2009...
-
Page 19: Install And User Manual
Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH AK-350 ALTITUDE ENCODER T2000UAV-L Installation and User Manual 01R1.doc Page 19 of 24 July 2009... -
Page 20: Install And User Manual
Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH A-30 ALTITUDE ENCODER T2000UAV-L Installation and User Manual 01R1.doc Page 20 of 24 July 2009... -
Page 21: Install And User Manual
Microair Avionics T2000UAV-L Install and User Manual MICROAIR AVIONICS T2000UAV-L TRANSPONDER WIRING DIAGRAM WITH SERIAL ALTITUDE DTA INPUT T2000UAV-L Installation and User Manual 01R1.doc Page 21 of 24 July 2009... -
Page 22: Pin Assignments
PIN 22 POWER GROUND PIN 23 POWER GROUND PIN 24 POWER 14 OR 28 VOLTS DC (10-33 VOLTS) PIN 25 POWER 14 OR 28 VOLTS DC (10-33 VOLTS) T2000UAV-L Installation and User Manual 01R1.doc Page 22 of 24 July 2009... -
Page 23: Specifications
Mode 3A (4096 codes) Mode 3A/C Temperature -20° C to +55°C Dimensions Width 61mm Height 61mm Length 134mm Weight 454 g (16 oz) Specifications are subject to change without notice. T2000UAV-L Installation and User Manual 01R1.doc Page 23 of 24 July 2009... -
Page 24: Limited Warranty
13.0 LIMITED WARRANTY T2000UAV-L Installation and User Manual 01R1.doc Page 24 of 24 April, 2009...
Need help?
Do you have a question about the T2000UAV-L and is the answer not in the manual?
Questions and answers