Subscribe to Our Youtube Channel
Summary of Contents for Vishay BLH LCp-100
- Page 1 LCp-100/200R Remote Digital Display Units Operator's Manual TM043 Rev C 6/1/11 Doc 35115...
- Page 2 NOTICE BLH makes no representation or warranties of any kind whatsoever with respect to the contents hereof and specifically disclaims any implied warranties or merchantability or fitness for any particular purpose. BLH shall not be held liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this publication or its contents.
-
Page 3: Table Of Contents
Table of Contents SECTION 1. Introduction ......................... 1-1 PRODUCT DESCRIPTION ......................1-1 MOUNTING OPTIONS ......................1-1 SPECIFICATIONS ........................1-2 WARRANTY POUCY ......................... 1-2 FIELD ENGINEERING ....................... 1-1 SECTION 2. Installation ........................2-1 INTRODUCTION ........................2-1 MOUNTING ..........................2-1 2.2.1 Standard Unit Mounting ....................... 2-1 2.2.2 Optional NEMA 414X Enclosures .................. -
Page 4: Introduction
SECTION 1. Introduction PRODUCT DESCRIPTION BLH Remote Digital Displays (Figure 1-1, 1-2) receive and display serial ASCII data transmitted by a BLH host LCp100, LCp-200, or Baldwin Model 2020 series weight indicator/ transmitter. Operating on supplied data, the Remote Display precisely duplicates the weight, rate*, or tension value display of the host device. -
Page 5: Specifications
SPECIFICATIONS Display Communications Type high intensity cobalt green vacuum Serial RS-485 two-wire, half duplex fluorescent 7 digit alpha-numeric 0.59” high for weight, Baud Rate 9600 Active Digits 8 digit alpha-numeric 0.39 “ high for stabs Environment Approvals/Certifications Operating Temp. -10 to 55°C (15 to 131°F) FM (Factory 3611: (Mass I,II,III;... -
Page 6: Field Engineering
FIELD ENGINEERING Authorized BLH Field Service Engineers are available around the world to install LCp Remote Display systems and/or train factory personnel to do so. The field service department at BLH is the most important tool to assure the best performance from your application. -
Page 7: Installation
SECTION 2. Installation Standard Remote Display Units are shipped with INTRODUCTION the necessary hardware for panel mounting. This chapter provides Remote Display mounting Outline and panel cutout dimensions are and electrical installation information. depicted in Figure 2-1. Installation of panel Instruments will operate accurately (to mount adapters is shown in Figure 2-2. - Page 8 Figure 2-2. Panel Mounting Configuration Figure 2-3. NEMA 4/4X Outline Dimensions...
-
Page 9: Electrical Connections
Figure 2-4. Interface Overview ELECTRICAL CONNECTIONS Figure 2-4 presents an overview of all wiring connections. Use this interface diagram for interface connections between the Remote Display and host instrument. Individual connections are discussed in the following paragraphs. Figure 2-5. Rear Panel Connection Locations 2.3.1 THE REMOTE DISPLAY REAR PANEL Figure 2-5 shows the Remote Display rear... -
Page 10: Introduction
2.5.1 DISPLAY MODE The front panel display can be configured to track the front panel of the host LCp/2020 instrument or fixed to display only one mode of host operation. In tracking mode, any host mode change (i.e. Net/Gross/ Rate) is immediately transmitted and displayed upon the remote Figure 2-6. -
Page 11: Operation
SECTION 3. Operation DISPLAY OPERATION Upon power up of both units, remote digital displays provide digit-for-digit display duplication of the host device display readout. Display updates, occurring approximately ten times a second, include weight, rate*, level, and alarm status data. If a fixed display format is selected, the remote unit can display one mode such as net or rate* while the host device displays a different mode such as gross. - Page 12 3 Edgewater Drive, Norwood, MA 02062 U.S.A Phone (781)298-2200 Fax (781)762-3988 www.vishaypg.com...
Need help?
Do you have a question about the BLH LCp-100 and is the answer not in the manual?
Questions and answers