Summary of Contents for Yeastar Technology EC25-E
- Page 1 4G LTE Module User Guide Version 1.2 Date: July 19, 2017 Yeastar Information Technology Co. Ltd.
-
Page 2: Table Of Contents
Yeastar 4G LTE Module User Guide Contents Introduction ......................3 4G LTE Module Features ........................ 3 4G LTE Module Frequency Bands ....................3 Installation ......................4 Hardware Overview ......................... 4 Installing the SIM Card ........................4 Installing the 4G LTE Module ......................5 Configuring Cellular Network ................... -
Page 3: Introduction
Yeastar 4G module supports 3G and 4G network. The Table 1 shows the operating regions and frequency bands for Yeastar 4G LTE modules. Table 1 4G LTE Module Frequency Bands Yeastar 4G Module Operating Region LTE FDD: B1/B3/B5/B7/B8/B20 EC25-E Europe WCDMA: B1/B5/B8 LTE TDD: B38/B40/B41 EC25-A North America... -
Page 4: Installation
Yeastar 4G LTE Module User Guide Installation Hardware Overview Front View Back View Installing the SIM Card Note: if the 4G LTE module is installed on the PBX, you need to power off the PBX before you start to install or remove the SIM card. Unlock the SIM card slot. -
Page 5: Installing The 4G Lte Module
Yeastar 4G LTE Module User Guide Installing the 4G LTE Module Important: Please first power down the PBX, then install the 4G LTE module. For S20/S50, you need to install the 4G LTE module into Slot1 if you want to use 4G cellular ... -
Page 6: Configuring Cellular Network
Yeastar 4G LTE Module User Guide Configuring Cellular Network After installing the 4G LTE module on Yeastar S-Series VoIP PBX, the PBX will automatically identify the SIM card carrier and use 4G network as the preferred cellular network. Verifying Signal Strength and Network Status Step 1. -
Page 7: Changing 4G Lte Network
Yeastar 4G LTE Module User Guide network via “Settings > System > Network”. Changing 4G LTE Network Changing 4G Network Type Navigate to “Settings > PBX > Trunks”, edit your 4G LTE trunk, click “Advanced” tab, change the network type according to your network circumstance. For example, if the 3G network is better than 4G in your place, then choose 3G. - Page 8 Yeastar 4G LTE Module User Guide communication with the CARRIER via the dial up connection parameters. By default, you don’t need to configure the dial-up settings. Yeastar S-Series VoIP PBX can identify the SIM card and dial up to connect to the Internet. Generally, you need to configure Dial-up settings for the following situations: The SIM card is installed in a place where the carrier network is not covered.
-
Page 9: Managing Cellular Data
Yeastar 4G LTE Module User Guide Managing Cellular Data Step 1. Navigate to “Settings > System > Network > Cellular Network”, and set Data Control settings to manage the cellular data. Generally, the cellular data is paid by month. Below we give an example of how to manage cellular data by month. -
Page 10: Changing Pbx's Network
Yeastar 4G LTE Module User Guide Changing PBX’s Network By default, the PBX uses wired network, and cellular network is disabled. You can go to “Settings > System > Network”, change the Cellular Network: Never: never use cellular network on the PBX. ... - Page 11 Yeastar 4G LTE Module User Guide ICMP Detection ICMP detection is used to check if the current connectivity is active. If you choose cellular network as a failover network, you need to enable ICMP detection. 1. Check the checkbox for “Enable ICMP Detection”. 2.
-
Page 12: Accessing Pbx Via Cellular Network
Yeastar 4G LTE Module User Guide Accessing PBX via Cellular Network Note: To access PBX via cellular network, first ensure that your cellular network is a public IP address. You cannot access PBX via a private cellular network. Log in the PBX Web user interface, click “Resource Monitor” button at the top-right corner, and scroll down to check the IP address of cellular network. -
Page 13: Setting Up Volte Calls
Yeastar 4G LTE Module User Guide Create a or peer-to-peer VoIP trunk on other device to connect to S-Series PBX Note: if you set the “Cellular Network” to “Always”, you can register remote extensions/trunks using the public IP address; if you set “Cellular Network” to “Failover”, you need to set DDNS on S-Series PBX first, and use the domain to register remote extensions/trunks. - Page 14 Yeastar 4G LTE Module User Guide Sending SMS to Email Go to “Settings > PBX > Call Features > SMS > SMS to Email”. Choose a 4G LTE trunk and click Click to add email address. Click “Save” and “Apply”. When you send a SMS from your mobile to the 4G trunk number, the SMS message will be delivered to the email address.