Table of Contents
Advertisement
Quick Links
H.V.L.P GRAVITY SPRAY GUN
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
BRIGGS & STRATTON IS A TRADEMARK OF BRIGGS & STRATTON CORPORATION AND IS USED UNDER LICENSE TO ALTON INDUSTRY LTD. GROUP
Operator's Manual
Product Model # 6388-00
Manual # 80018896
Read and understand this
instruction manual thoroughly
before using the product. It
contains important information
for your safety as well as
operating and maintenance
advice.
Advertisement
Table of Contents
Related Manuals for Briggs & Stratton 6388-00
Summary of Contents for Briggs & Stratton 6388-00
- Page 1 H.V.L.P GRAVITY SPRAY GUN Operator’s Manual Product Model # 6388-00 Manual # 80018896 Read and understand this instruction manual thoroughly before using the product. It contains important information for your safety as well as BRIGGS & STRATTON CORPORATION operating and maintenance advice.
- Page 2 Thank you for purchasing this quality-built Briggs & Stratton™ air tool. We are pleased that you’ve placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your Briggs & Stratton air tool will provide reliable service. Where to Find Us You can contact Briggs &...
-
Page 3: General Safety Information
General Safety Information 8. Do not operate the tool if it is damaged during shipping, handling or use. Damage could result in bursting and cause injury and/or property damage. The safety alert symbol is used to identify safety 9. Never spray flammable materials in vicinity of open information about hazards that can result in personal flame or near ignition sources. -
Page 4: Product Description
2. Connect air supply hose (not included) with the air inlet (I) of spray gun (A). Use seal tape (not included) for airtight connection. Do not overtighten. (See Figure 2) 6388-00 H.V.L.P GRAVITY SPRAY GUN PISTOLA DE PULVERIZACIÓN DE GRAVEDAD HVLP PISTOLET À... - Page 5 4. Holding the gun 6-12 in. away from workpiece depending ● Test the consistency of the paint by making a few strokes on material and atomizing pressure, spray a short burst on a cardboard target. If paint still appears too thick, add a while turning the fluid adjustment knob (G) until desired small amount of thinner.
-
Page 6: Care And Maintenance
6. Trigger the gun properly. Start the gun moving at the 2. Refill the paint cup with clean solvent and attach the cup beginning of the stroke before squeezing the trigger (J) to the gun body. Spray solvent through the gun into a and release the trigger (J) before stopping gun movement container while shaking the spray gun. -
Page 7: Troubleshooting
STORING 1. When not using the spray gun, turn the fluid adjustment knob counterclockwise to open fully. This will reduce the spring tension on the fluid needle tip. 2. The spray gun must be well cleaned and lightly lubricated. 3. Store the spray gun in a dry and safe place out of reach of children. Troubleshooting PROBLEM POSSIBLE CAUSE... -
Page 8: Exploded Diagram And Parts List
Exploded Diagram and Parts List Description Qty. Description Qty. Part No. Part No. Gun body E-clip O-ring O-ring Needle packing screw Pattern regulating seat Air ring O-ring Gasket Pattern regulating valve Nozzle seat Patern adjustment knob Fluid nozzle Screw E-clip E-clip Air cap Trigger... -
Page 9: Limited Warranty
Briggs & Stratton™ Air Tool Warranty Policy January, 2016 LIMITED WARRANTY Briggs & Stratton™ is a trademark of BRIGGS & STRATTON CORPORATION and is used under license to Alton Industry Co. Ltd® Alton Industry Co. Ltd warrants this Briggs & Stratton brand product for a period of one year from the date of original retail purchase against defects in materials and workmanship.