Century VGreen Installation Manual And User's Manual

Century VGreen Installation Manual And User's Manual

Motor automation adapter kit

Advertisement

VGreen
Motor Automation Adapter Kit
®
Installation Manual and User's Guide
For use with Century
• Read and follow all instructions carefully.
• Disconnect and lock out power before installation and maintenance. Working on or near energized equipment could result in severe
injury or death.

TABLE OF CONTENTS

1.0 KIT CONTENTS ....................................................................................................... 1
2.0 INTRODUCTION ...................................................................................................... 2
3.0 OVERVIEW .............................................................................................................. 2
4.0 CONNECTING TO A VGREEN MOTOR ................................................................... 2
5.0 CONNECTING TO AN ALTERNATE POWER SOURCE ........................................... 5
6.0 CONNECTING TO AN AUTOMATION SYSTEM ..................................................... 5
6.1 Using automation system output connectors .................................................. 5
6.2 Using automation system relays ........................................................................ 5
6.2.1 Connecting to input side of relays ............................................................... 5
6.2.2 Connecting to output side of relays ............................................................ 6
6.2.2.1 Output signal powered by automation adapter .................................. 6
7.1 Adjusting motor speed ......................................................................................... 6
8.0 FAULT STATUS ........................................................................................................ 7
9.0 TROUBLESHOOTING GUIDE ................................................................................. 7
10.0 SPECIFICATIONS ..................................................................................................... 7

1.0 KIT CONTENTS

PART
NUMBER
Autolmation
2517369-001
Adapter
Digital Input
2517463-001
Cable
Lead Cable
2517465-001
RS-485
2511130-001
Connector
Conduit Fitting
2017587-002
1
VGreen variable speed motors
®
MOTOR AUTOMATION ADAPTER ................................ 6
®
PART
QTY
IMAGE
1
4
25 FT
1
1
Regal Beloit America, Inc.
1325 Heil Quaker Blvd.
LaVergne, TN 37086
Customer Service: 1-800-262-6484
www.RegalBeloit.com
PART
PART
NUMBER
2513409-001
Terminal Box
(Grey)
2513409-002
Cover Assembly
(Black)
Plug
2514059-001
Screw Driver
2517831-001
F O R M
C0048E
Revised
December 2018
QTY
IMAGE
1
4
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the VGreen and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Century VGreen

  • Page 1: Table Of Contents

    1.0 KIT CONTENTS ....................... 1 2.0 INTRODUCTION ...................... 2 3.0 OVERVIEW ......................2 4.0 CONNECTING TO A VGREEN MOTOR ..............2 5.0 CONNECTING TO AN ALTERNATE POWER SOURCE ........... 5 6.0 CONNECTING TO AN AUTOMATION SYSTEM ............. 5 6.1 Using automation system output connectors ..........5 6.2 Using automation system relays ................
  • Page 2: Introduction

    Motor Automation Adapter provides the ability to ® IN1, IN2, IN3, IN4: 9-30 VAC/VDC (2mA Typical, 22mA MAX) operate a VGreen motor with a 3rd party automation system such Connect to relay coil or valve control of automation system. as the Hayward...
  • Page 3 3. Remove the 3/8” conduit hole plug with a 5/16” 6. Remove the user interface from the controller (four screws). allen wrench. Figure 6: 3/8” Conduit hole plug removed Figure 9: User interface and rubber gasket removed 4. Remove the plastic wiring cover inside the terminal box 7 .
  • Page 4 Dip switches one and two of the VGreen motor need to be on in ® order for the automation adapter to function. REFER TO THE VGREEN MOTOR USER MANUAL FOR DIP SWITCH POSITIONING. 9. Replace the plastic cover inside the terminal box (one screw).
  • Page 5: Connecting To An Alternate Power Source

    13. Connect the four wires from the motor to the automation OUTPUTS adapter. (i.e. AUX1) VGreen ® Motor J103 Figure 17: Motor connected to adapter 5.0 CONNECTING TO AN ALTERNATE POWER SOURCE: VGreen ® If you choose not to power the automation adapter from the...
  • Page 6: Connecting To Output Side Of Relays

    6.2.2 Connecting to input (i.e. high voltage) side of relays 7.0 OPERATING A VGREEN MOTOR ® AUTOMATION ADAPTER 6.2.2.1 Output signal powered by automation adapter From the 10V connection of the automation adapter board (CON1), run a wire to the input on desired relays. Run the output of the relay to the right pin of an input on the automation board (IN1-IN4).
  • Page 7: Fault Status

    -30°C to 80°C (-22°F to 176°F) Operating 0°C to 50°C (32°F to 122°F) Humidity 0-85% Non-condensing Regal, Century and VGreen are trademarks of Regal Beloit Corporation or one of its affiliated companies. ©2013, 2018 Regal Beloit Corporation, All Rights Reserved. MCIM18021E • Form# C0048E...

Table of Contents