Table of Contents
Advertisement
Owner's Manual & Safety Instructions
Save This Manual
operating, inspection, maintenance and cleaning procedures. Write the product's serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
©
Copyright
2017 by Harbor Freight Tools
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Keep this manual for the safety warnings and precautions, assembly,
Visit our website at: http://www.harborfreight.com
®
. All rights reserved.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
17i
Advertisement
Table of Contents
Related Manuals for Badland Winches 63476
Summary of Contents for Badland Winches 63476
- Page 1 Owner’s Manual & Safety Instructions Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
- Page 2 (15.2m) First Layer of Wire Rope Performance Line Pull Line Speed Amp Draw lb. (kg.) fpm (mpm) (@ 12V) 13.3 (4.1) 1000 (454) (2.5) 2000 (907) (1.2) 2500 (1134) (0.8) Page 2 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 3 Fingers may be caught and get provided against the intrusion of solid pulled into fairlead or drum. objects, dust, accidental contact, and water. Grade 8 Pull hook using strap only. A fastener strength rating. Item 63476 For technical questions, please call 1-888-866-5797. Page 3...
- Page 4 6. Do not place finger(s) through hook. Fingers may see Double Line Rigging on page 11. be caught and get pulled into fairlead or drum. Use included strap to hold hook instead. Page 4 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 5 This illustration shows a kink about Otherwise, wire rope may bind during operation. to form. At this point the winch should be stopped and the wire rope should be straightened out to prevent kinking. Item 63476 For technical questions, please call 1-888-866-5797. Page 5...
- Page 6 Do not use thinner/ longer cables or link multiple cables together. 2. Disconnect power to winch and allow it to cool completely before service. Page 6 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 7 Vehicle components are not damaged by drilling or driving screws. 5. Secure in place with mounting screws. d. Winch components will not be damaged by stresses caused by vehicle operation. Item 63476 For technical questions, please call 1-888-866-5797. Page 7...
- Page 8 3. Recoil the wire rope back into the winch to be able to support a load without damage. under at least 500 lb. of tension. 2. Uncoil the wire rope, except for 5 full wraps. Page 8 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 9 1. Turn Remote Transmitter over. 4. Pull battery out of unit and replace with same. 2. Remove screws from battery cover. Note: Do not reverse polarity of the battery. 3. Remove battery cover carefully. Item 63476 For technical questions, please call 1-888-866-5797. Page 9...
- Page 10 If the wire rope should slip or break, it can suddenly whip back towards the winch, causing a hazard for anyone in the area. Stand well to the side while winching. Page 10 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 11 Correct any such issue before use. the vehicle cannot start. However, exercise extreme caution when working around a running vehicle and ONLY operate a vehicle in an outdoor area. Item 63476 For technical questions, please call 1-888-866-5797. Page 11...
- Page 12 14 minutes, 15 seconds after every 45 seconds of continuous operation. Failure to carefully observe duty cycle limitations can easily over-stress a Winch contributing to premature Winch failure. Page 12 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 13 20 seconds until the LED flashing turns solid. 3. Press and hold both EXTEND & RETRACT buttons again for 3 seconds until LED turns off and then lights up. Receiver Transmitter Figure K Item 63476 For technical questions, please call 1-888-866-5797. Page 13...
- Page 14 LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. Page 14 For technical questions, please call 1-888-866-5797. Item 63476...
- Page 15 Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Item 63476 For technical questions, please call 1-888-866-5797. Page 15...
- Page 16 Limited 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase.
Need help?
Do you have a question about the 63476 and is the answer not in the manual?
Questions and answers
WILL THE REMOTE SW ASSY WORK ON OLDER 2500 LB ATV AND WHAT WOULD IT COST
Yes, the Badland 63476 remote switch assembly is designed for utility, shop, and ATV applications with a 2,500 lb capacity, so it is compatible with older 2,500 lb ATVs as long as they meet the power and mounting requirements.
This answer is automatically generated