1. Manuals
  2. Brands
  3. Linak Manuals
  4. Racks & Stands
  5. Kick & Click
  6. User manual

Linak Kick & Click User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Kick & Click
TM
User manual
LINAK.COM/DESKLINE
Page 1 of 32

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Kick & Click and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Linak Kick & Click

Summary of Contents for Linak Kick & Click

  • Page 1 Kick & Click User manual LINAK.COM/DESKLINE Page 1 of 32...

  • Page 2: Table Of Contents

    Assembling a three-legged desk ....................17 Mounting tabletop ........................18 Disassembly ..........................20 Accessories and repair ......................... 21 Disposal of LINAK’s products ..................... 22 Drawing appendix ........................23 Declaration of confirmity ......................31 Addresses ............................32 Page 2 of 32...

  • Page 3: Preface

    This User Manual does not address the end-user. It is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It is the responsibility of the manufacturer of the end-user product to provide a User Manual where relevant safety information from this manual is passed on to the end-user.

  • Page 4: Important Information

    Important information Important information on LINAK products can be found under the following ® headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed.

  • Page 5: Before Installation, Re-Installation Or Troubleshooting

    • System connection. The individual parts must be connected before connecting the control box to the mains. See the User Manual for LINAK actuators, if necessary. During operation • If the control box makes unusual noise or smells, switch off the mains voltage immediately.

  • Page 6: Only For Eu Markets

    Only for EU markets This appliance can be used by children aged from aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

  • Page 7: Repairs

    Repairs In order to avoid the risk of malfunction, all DESKLINE repairs must only be carried out by authorised LINAK workshops or ® repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned to authorised LINAK workshops.

  • Page 8: Misc. On The Deskline ® System

    There is a 60 month warranty on Kick & Click systems. Read more about the warranty period of the motorsystems in the standard user manuals found on www.linak.com/deskline. Maintenance Clean dust and dirt off the outside of the system at appropriate intervals and inspect them for damage and breaks.

  • Page 9: Description Of The Deskline ® Kick & Click Tm System

    Description of the DESKLINE Kick & Click system ® The Kick & Click system is the smart and intuitive solution for mounting DESKLIFT™ columns to the tabletop. The solution is perfect for various office desks. The unique feature of Kick & Click is the way of mounting. Click the system together without using tools and screws, simply clever.

  • Page 10: Kick & Click Tm Adjustable

    Kick & Click Adjustable The Adjustable system includes a telescopic inner and outer rail onto which the base is welded. Kick & Click Fixed Compared to the Adjustable system the Fixed system only consists of one rail which is welded onto the base in both ends. Page 10 of 32...

  • Page 11: Kick & Click Tm Base

    Kick & Click Base The Base system is without the inner and the outer rail. The system is preferred if the OEM want to weld his own rail onto the Base, or if the desk design does not need a rail e.g. due to tabletop thickness. The Base system could also be used for a 3 leg desk.

  • Page 12: Kick & Click Tm 3 Rd Leg Kit

    Kick & Click leg kit The 3 leg kit system includes a telescopic inner and outer rail with a base welded onto the outer rail. Page 12 of 32...

  • Page 13: Mounting Guidelines For The Kick & Click

    Mounting guidelines for the Kick & Click system Kick & Click Adjustable 1. Gather all parts for desk 2. Fix inner rail with outer rail (only Kick & Click Adjustable). 2.1. Extend rails to required length 2.2. Fix length with clip. (frame width from 1140 to 1940 mm) using holes on rails as a length indicator.
  • Page 14 4. Align cantilever T-desk C-desk Align middle marker on cantilever with Outer markers on cantilever indicate 50 mm centre on inner rail/outer rail maximum displacement from centre on inner rail/outer rail 5. Mount column by placing it in base. Column is prepared for Kick & Click™ with slots on backside of housing (see drawings) Page 14 of 32...
  • Page 15 6. Place clamp on column housing, press it down gently. It will still be possible to move clamp a little when placed. 7. Place Kick Lock in clamp. Arrow on Kick Lock must face arrow on clamp. 8. Fix Kick Lock in clamp with your foot. When you hear a “click”, Kick Lock is mounted and column is fixed together with Kick &...
  • Page 16 9. Turn tabletop upside down. 10. Place assembled Kick & Click in preferred position. 11. Mark and predrill holes in tabletop, if not done yet. 12. Fasten Kick & Click to tabletop with screws (in inner/outer rails and cantilevers). 13. Mount and connect electronics. 14.

  • Page 17: Assembling A Three-Legged Desk

    Assembling a three-legged desk The 3 leg kit has only one base which is welded onto the outer rail. Mount Kick & Click Adjustable system as described above. 1. Gather all 3 leg kit system parts. 2. Fix inner rail with outer rail. 2.1.

  • Page 18: Mounting Tabletop

    Mounting tabletop The oval holes in the inner and outer rails and in the cantilevers of the Kick & Click system facilitate mounting of tabletops with predrilled holes. Old Kick & Click versions with circular holes Do not predrill holes for all the parts. The combination of hole tolerances on each part, e.g.
  • Page 19 1. Turn tabletop upside down. 2. Place assembled Kick & Click in preferred position. 3. Mark and predrill holes in tabletop, if not done yet. 4. Fasten Kick & Click to tabletop with screws (in inner/outer rails and cantilevers). 5. Mount and connect electronics. 6.

  • Page 20: Disassembly

    Disassembly A disassembling instruction video is available here. Disassembling Kick & Click. 1. Remove Kick Lock. Keep pressing while removing Kick Lock using a screwdriver Gently press two pins on side of Kick Lock 3. Place screwdriver in one of holes on clamp and twist 2.

  • Page 21: Accessories And Repair

    ® Repairs Systems should only be repaired by an authorised LINAK service centre or engineer. Systems to be repaired under warranty must be sent to an authorised LINAK service centre. Warning! By unauthorised opening of the system there is a risk that it may malfunction at a later date.

  • Page 22: Disposal Of Linak's Products

    Disposal of LINAK product As LINAK’s customers often ask us how our products can be disposed or scrapped we have prepared this guide that enables a classification to different waste fractions for recycling or combustion. Guide We recommend our products to be disassembled as much as possible and divided into different waste groups for recycling or combustion.

  • Page 23: Drawing Appendix

    DRAWING APPENDIX Kick & Click Adjustable Kick & Click Fixed Page 23 of 32...
  • Page 24 Drawing No.: KICK_AND_CLICK_BASE Drawing No.: KICK_AND_CLICK_BASE Kick & Click Base 5.3* 5.3* * The holes on the unpainted base are Ø5.5 mm. Kick & Click 3 leg kit Page 24 of 32...
  • Page 25 DL5/DL6 on top mounted column, 560 mm DL5/DL6 on top mounted column, 710 mm Page 25 of 32...
  • Page 26 DL10/DL11/DL14/DL17/DL19 on top mounted column, 560 mm DL10/DL11/DL14/DL17/DL19 on top mounted column, 710 mm Page 26 of 32...
  • Page 27 DL5/DL6 recessed mounted column, 560 mm DL5/DL6 recessed mounted column, 710 mm Page 27 of 32...
  • Page 28 DL10/DL11/DL14 recessed mounted column, 560 mm DL10/DL11/DL14 recessed mounted column, 710 mm Page 28 of 32...
  • Page 29 DL17/DL19 recessed mounted column, 560 mm DL17/DL19 recessed mounted column, 710 mm Page 29 of 32...
  • Page 30 Adjustment screw Page 30 of 32...

  • Page 31: Declaration Of Confirmity

    LINAK customer using any LINAK product. LINAK shall be responsible solely that the LINAK products comply with the specifications set out by LINAK and it shall be the responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question.

  • Page 32: Addresses

    While LINAK uses its best efforts to fulfil orders, LINAK cannot, for the same reasons as mentioned above, guarantee the availability of any particular product. Therefore, LINAK reserves the right to discontinue the sale of any product displayed on its website or listed in its catalogues or other written material drawn up by LINAK.

Table of Contents