Advertisement
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Asoka Plugline PL7667-ETH
Summary of Contents for Asoka Plugline PL7667-ETH
- Page 1 PlugLine Smart Energy AV Ethernet User’s Guide PL7667-ETH 66-0366-01Rev.003...
- Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Asoka equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: Turn the television or radio antenna until the interference stops.
- Page 3 IN THE EVENT SHALL ASOKA BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OF INABILITY TO USE THIS MANUAL, EVEN IF ASOKA HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
-
Page 4: Table Of Contents
Table of Contents Chapter Title Page Introduction Important Safety Instructions for the PlugLink Overview Installation Getting Started with the PlugLink Basic PL7667-MST Configuration PL7667-MST Administration Reset and network of PLC Appendix A Quick Guide to the PlugLink Default Settings... - Page 5 Asoka® User Guide PlugLink PL7667-ETH Chapter 1 Audience This guide is designed as a reference for the networking or computer technician responsible for installing a PlugLink PL7667-ETH, hereafter referred to as the gateway. It is assumed that you are familiar with and have a working knowledge of the concepts and terminology associated with Ethernet and local area networking.
- Page 6 Asoka® User Guide PlugLink PL7667-ETH You can access the most current PlugLink™ documentation on the Asoka website at this URL: http://www.asokausa.com Document Feedback You can submit comments via email to custserv@asokausa.com You can also submit your comments via regular mail by writing to the following address:...
- Page 7 Asoka® User Guide PlugLink PL7667-ETH Chapter 2 Important Safety Instruction for the PlugLink PL7667-ETH The following precautions should be taken when using this product: Read all instructions before installing and operating this product. Do not open the cover on this product and/or alter this product in any way.
-
Page 8: Overview
Asoka® User Guide PlugLink PL7667-ETH Chapter 3 Overview This chapter provides information about the following topics: Features Package Contains Front Panel Description Rear Panel Description Features PlugLink 7667–ETH features: Utilizes the existing electrical wiring to distribute data services IEEE 802.3, 802.3u, 802.3x, 802.3z/ab, 802.1q... - Page 9 Asoka® User Guide PlugLink PL7667-ETH Figure 3-1: PL7667-ETH Top Panel The Front Panel The front panel of the PL7667 contains the one Power Outlet. Figure 3-2: PL7667-ETH Front Panel Page 9 of 33...
- Page 10 Asoka® User Guide PlugLink PL7667-ETH Side Panel You can use the status lights to verify connections. Viewed from top to bottom, the table bellow describes the lights on the side panel of the unit. Table 3-1: Status Light Descriptons Power...
- Page 11 Asoka® User Guide PlugLink PL7667-ETH Operating System and Browser Support You can access the web-based interface by using the operating systems and browsers listed in Table 3-2. Minimum Microsoft Mozilla Firefox Netscape Other Service Pack Internet Communicator or Patch Explorer...
- Page 12 Asoka® User Guide PlugLink PL7667-ETH Ensure that your Internet browser popup blocker is disabled. To disable the popup blocker, follow these steps: Under Internet Explorer 1. Open a web browser. 2. Under the Tools menu, select Turn off Popup Blocker.
-
Page 13: Installation
Asoka® User Guide PlugLink PL7667-ETH Chapter 4 Installation This chapter describes how to install your CPE device and how to interpret the LEDs to ensure proper operation. Read the topics, and perform the procedures in the following order: Preparing for Installation... - Page 14 Asoka® User Guide PlugLink PL7667-ETH This product relies on the building’s installation for short-circuit (over current) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A International) is used on the phase conductors (all current-carrying conductors).
- Page 15 Asoka® User Guide PlugLink PL7667-ETH You can install the CPE simply by plugging directly into a power outlet or by physically mounting onto a power outlet. Before you begin the installation, decide how you want to install the CPE by reviewing the illustrations in these sections:...
- Page 16 Asoka® User Guide PlugLink PL7667-ETH Chapter 5 Getting Started with the PL7667-ETH This chapter provides a quick step-by-step installation and setup procedure guide for a standalone PL 7667-ETH. For detailed installation procedures for mounting your CPE, see Chapter 4, “Installation.” For product overview information, see Chapter 3, “Overview.”...
- Page 17 Asoka® User Guide PlugLink PL7667-ETH Assigning your PC to the same network as the CPE The –PL 7667 has an IP address: 192.168.1.254. For network access, you must manually assign your PC an IP address of 192.168.1.x, where “x” is a number between 1 and 254(excluding 253.)
- Page 18 Asoka® User Guide PlugLink PL7667-ETH The username and password are case sensitive. For security, you should set a unique system password after initial login. For instructions on how to set a unique system password, see Chapter 7. Understanding the PL7667-ETH Web Interface When you access the web-based user interface (UI), the System Details page is the first page you will see.
- Page 19 Asoka® User Guide PlugLink PL7667-ETH The UI is divided into five main logical sections and you can be directed to any of the five sections by clicking on their corresponding links. 2. Quick Sub Navigation Links In each of the five main logical sections, sub navigation links on the right will appear, providing you with logical links for each specific category.
-
Page 20: Basic Pl7667-Mst Configuration
Asoka® User Guide PlugLink PL7667-ETH Chapter 6 Basic PL7667–ETH Configuration This chapter presents procedures for configuring the basic parameters of your PL7667 interface, including IP, Subnet Mask and DNS settings. This chapter contains the following sections: LAN Settings Configuring your LAN Settings To configure the CPE’s LAN settings, click IP ADDRESS on the Main menu. - Page 21 Asoka® User Guide PlugLink PL7667-ETH 1. IP Address The IP Address is the internal IP address of the PL7667. The default IP address is 192.168.1.254. To access the PL7667 Setup Interface, type this IP address into the address or navigation bar of your web browser.
- Page 22 Asoka® User Guide PlugLink PL7667-ETH Figure 6-2: Device Scan Screen The Device Scan screen will only list Powerline devices on your network that have the same Powerline Network Encryption KEY (NEK). Page 22 of 33...
-
Page 23: Pl7667-Mst Administration
Asoka® User Guide PlugLink PL7667-ETH Chapter 7 PL7667–ETH Administration This chapter describes how to perform operations to administer your PL7667-ETH. This chapter consists of the following sections: Reboot Restoring Factory Default Firmware upgrade Reboot Sometimes it may be necessary to reboot the adapter if it is working improperly. Rebooting will not delete any of your configuration settings. - Page 24 Asoka® User Guide PlugLink PL7667-ETH Figure 7-1: Reboot screen Restoring Factory Defaults At times, you may need to restore factory default settings on the adapter. It is recommended that you back up your settings prior to restoring to factory default settings. To restore factory default settings: 1.
- Page 25 2. In the Sub menu, select Update Firmware. 3. Click Browse to locate the new firmware update file downloaded from Asoka’s web site. 4. The box next to the Browse button will now display the location and name of the firmware file you just selected.
- Page 26 Asoka® User Guide PlugLink PL7667-ETH Figure 7-3: Firmware upgrade screen. Page 26 of 33...
-
Page 27: Reset And Network Of Plc
Asoka® User Guide PlugLink PL7667-ETH Chapter 8 Reset and network of PLC The PL7667-ETH device has two hardware push buttons: FW RST (Firmware Default Reset ) button – Resets the PL7667-ETH back to factory default settings. Press and hold the button with a pin or sharp object for about 2 seconds until you see the lights on the device flash briefly. - Page 28 Asoka® User Guide PlugLink PL7667-ETH Figure 8-1: Two devices of PLC ADDING A THIRD OR MORE PLUGLINK HD AV DEVICES Ethernet light PLC ACT Device A Device B Device C 1. Plug your new PL7667-ETH (Device C) into an AC outlet. The POWER light indicator should be lit solid green.
- Page 29 Asoka® User Guide PlugLink PL7667-ETH 3. In about 15 seconds the POWER light will change from flashing green to solid green and the PLC ACT (Power line Communication Activity) light will turn solid green (flashing green when there is data traffic) indicating they are synchronized with the same NEK.
- Page 30 Appendix A Default Settings Login and Password: User Name: admin Password: welcome IP Setting: IP Address: 192.168.1.254 Subnet Mask 255.255.255.0 30 of 20...
- Page 31 FCC Notice FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Page 32 Asoka USA Corporation 2620 Augustine Drive Suite 230 Santa Clara, CA 95054 USA Phone: (408) 550–8167 Fax: (408) 884–2390 www.asokausa.com URL: www.asokatech.com...
Need help?
Do you have a question about the Plugline PL7667-ETH and is the answer not in the manual?
Questions and answers