Chapter 1 Introduction to GDM12864A LCM CHAPTER 1 Introduction to ITM-12864A LCM ITM-12864A is a dot matrix graphic LCD module which is fabricated by low power COMS technology. It can display 128*64 dots size LCD panel using a 128*64 bit-mapped Display Data RAM (DDRAM).
Chapter 1 Introduction to GDM12864A LCM Figure 1. External Dimensions SIGNAL DB2 DB3 SIGNAL *NOTE: 1.All units are mm. 2.Tolerances unless otherwise specified ? 0.2. INTECH MODULE ITM-12864A...
Chapter 1 Introduction to GDM12864A LCM Electro-Optical characteristics TN Type (Twisted Nematic ) Item Symbol Min. Typ. Max. Unit Condition Note Viewing Angle deg. Cr = 2.0 ?=20 Contrast Ratio f = 0 ?=20 Response Time (rise) f = 0...
Chapter 1 Introduction to GDM12864A LCM Electrical Absolute Maximum Ratings (KS0107B) Parameter Symbol Rating Unit Note Operating voltage -0.3 ~ +7.0 Supply voltage -19.0 ~ V +0.3 Driver supply voltage -0.3 ~ V +0.3 *1,2 -0.3 ~ V +0.3 *3,4 *Notes: *1.
Chapter 1 Introduction to GDM12864A LCM Electrical Absolute Maximum Ratings(KS0108B) Parameter Symbol Rating Unit Note Operating voltage -0.3 ~ +7.0 Supply voltage -19.0 ~ V +0.3 Driver supply voltage -0.3 ~ V +0.3 *1,3 -0.3 ~ V +0.3 *Notes: Based on V = 0V *2.
64CH Common Driver For Dot Matrix LCD CHAPTER 2 Driver IC Function Description KS0107 Driver IC 64COM graphic driver for dot matrix LCD Introduction The KS0107B is an :CD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic display systems.
64CH Common Driver For Dot Matrix LCD AC Characteristics (VDD=4.5~5.5V, Ta=-30? ~+85? ) 1. Master mode (MS=V , PCLK2=V , Cf=20pF, Rf=47KO) 0.7V 0.3V DIO1(SHL=V DIO2(SHL=V DIO2(SHL=V DIO1(SHL=V 0.7V 0.3V CLK1 CLK2 Characteristic Symbol Unit Data Setup Time Data Hold Time Data Delay Time FRM Delay Time M Delay Time...
64CH Common Driver For Dot Matrix LCD FUNCTIONAL DESCRIPTION 1.RC Oscillator The RC Oscillator generates CL2, M, FRM, of the KS0107B and CLK1, CLK2 of the KS0107B by the oscillation resister R and capacitor C. When selecting the master/slave, oscillation circuit is as following: Master Mode KS0107B KS0107B...
64CH Common Driver For Dot Matrix LCD Duty Selection (DS1, DS2) It provides various duty selection according to DS1, DS2. DUTY 1/48 1/64 1/96 1/128 Data shift & Phase Select Control Phase Selection It is a circuit to shift data on synchronization or rising edge or falling edge of the CL2 according to PCLK2.
64CH Segment Driver For Dot Matrix LCD CHAPTER 3 Driver IC Function Description KS0108 Driver IC 64 SEG graphic driver for dot matrix LCD Introduction The KS0108B is an LCD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic display systems.
Page 16
64CH Segment Driver For Dot Matrix LCD W H 1 C L K 1 0 .7 V 0 .3 V W L 1 D 1 2 D 21 C L K 2 W L 2 0 .7 V 0 .3 V W H2 ( 2) .Display Control Timing Characteristic...
Page 17
64CH Segment Driver For Dot Matrix LCD ( 3) . MPU Interface Characteristic Symbol Unit E Cycle 1000 E High Level Width E Low Level Width E Rise Time E Fall Time Address Set-Up Time Address Hold Time Data Set-Up Time Data Delay Time Data Hold Time (Write) Data Hold Time (Read)
64CH Segment Driver For Dot Matrix LCD CS1B,CS2B CS3,RS DB0~DB7 MPU Read timing OPERATING PRINCIPLES & METHODS I/O Buffer Input buffer controls the status between the enable and disable of chip. Unless the CS1B to CS3 is in active mode, Input or output of data and instruction does not execute. Therefore internal state is not change.
Page 19
64CH Segment Driver For Dot Matrix LCD Function Instruction Status read (busy check) Data write (from input register to display data RAM ) Data read (from display data RAM to output register) Reset The system can be initialized by setting RSTB terminal at low level when turning power on, receiving instruction from MPU.
Page 20
64CH Segment Driver For Dot Matrix LCD Display On/Off Flip-Flop The display on/off flip-flop makes on/off the liquid crystal display. When flip-flop is reset (logical low), selective voltage or non selective voltage appears on segment output terminals. When flip-flop is set (logic high), non selective voltage appears on segment output terminals regardless of display RAM data.
64CH Segment Driver For Dot Matrix LCD Display Control Instruction The display control instructions control the internal state of the KS0108B. Instruction is received from MPU to KS0108B for the display control. The following table shows various instructions. Instruction Function Reads data (DB[7:0]) from Read Display Read data...
Page 22
64CH Segment Driver For Dot Matrix LCD Set Page (X Address) X address (AC0~AC2) of the display data RAM is set in the X address register. Writing or reading to or from MPU is executed in this specified page until the next page is set. Display Start Line (Z Address) Z address (AC0~AC5) of the display data RAM is set in the display start line register and displayed at the top of the screen.