1. Manuals
  2. Brands
  3. Audio Manuals
  4. Enclosure
  5. A10-RACK
  6. User manual

Audio A10-RACK User Manual

4-slot wireless enclosure
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
A10-RACK
4-Slot Wireless Enclosure
—
—
User Guide
Fits Most Unislot and Superslot
Receivers
™

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the A10-RACK and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Audio A10-RACK

  • Page 1 A10-RACK 4-Slot Wireless Enclosure — — User Guide Fits Most Unislot and Superslot Receivers ™...

  • Page 2: Table Of Contents

    Key Features . . . . . . . . . . . . . . . . . 3 Updating RX via A10-RACK . . . . . . . . . . 8 Compatible Receivers .

  • Page 3: Overview

    A10-RACK User Guide Overview The A10-RACK is a 4 slot, 8 channel, 1RU wireless microphone receiver enclosure, compatible with most Unislot and SuperSlot receivers. The A10-RACK accepts up to 4 dual-channel slot-in ™ receivers, providing a total of 8 separate audio feeds. The A10-RACK provides high-quality an- tenna distribution, power distribution, up to 8 channels of analogue and/or AES digital audio via XLR-M connectors and an 8 channel Dante audio interface.

  • Page 4: Panels: Connectors, Controls And More

    A10-RACK User Guide Panels: Connectors, Controls and More Figure 1: Full Front Panel of A10-RACK Figure 2: Closeup of Leftmost Slot on Front Panel of A10-RACK 1 -Four Receiver Slots 2 -Antenna Distribution Leads Each slot accepts one (single- or dual- SMA cables (included) are used to channel) 25-pin SuperSlot or unislot receiver.

  • Page 5: Rack Mounting

    Figures 1, 2 and 3 may be installed in any one of three possible positions to allow the user to set the depth of the front of the A10-RACK to accommodate a rack door or cover. - 5 -...

  • Page 6: Powering

    The A10-RACK is powered with a standard 4-pin F-XLR 10-18vdc power supply (sold separately), such as the Sound Devices XL-WP4. Power to A10-RACK needs to be capable of providing 3A minimum for proper powering of the A10-RACK and the slot receivers.

  • Page 7: Dante

    CAT5 or CAT6 cable and standard gigabit switches and hardware to many devices simultaneously. This makes Dante especially attractive for the user of the A10-RACK because all eight channels of audio from the wireless receivers can be transported over a single CAT5 network cable.

  • Page 8: Operation

    2. Connect antennas to the A10-RACK. 3. Connect XLR cables for analogue/AES output as needed. 4. If using a Dante network, connect the A10-RACK to the network using a shielded Cat5e cable. 5. Power on either using “ON+ ” for active antennas or using “ON” for passive.

  • Page 9: Cascading A10-Rack Units

    2nd (or next level) are filled - this is good RF practice and will achieve best performance. The Dante ports may also be daisy-chained if the A10-RACK is not setup for redundant opera- tion (set to “switched” in Dante Controller).

  • Page 10: Legal Notices

    Declarations of Conformity Hereby, Audio Ltd declares that the radio equipment type A10-RACK is in compliance with Low Voltage Directive 2014/35/EU, EMC Directive 2014/30/EU, and RoHS Directive 2011/65/EU. The full text of the EU Declaration of Conformity and full text of the Supplier Declaration of Conformity for US are available at the following internet address: www.audioltd.com/DoC...

Table of Contents