Table of Contents
Advertisement
Quick Links
HP10
SL 3.0
Thermometer with recorder
Handbook
MAIN SETTINGS (Run Mode).
MAXIMUM TEMPERATURE RECORDING VIEW.
Press + :
This message will be displayed followed by
° Maximum temperature recording.
MINIMUM TEMPERATURE RECORDING VIEW.
Press + :
This message will be displayed followed by
° Minimum temperature recording.
MEMORY CLEAR.
Press CLEAR for more two seconds:
This message will be composed on display before
clearing operation.
COSt PROGRAMMING (System constants)
These settings refer to the mode operation of the system and must be made on
initial start-up.
Press - / + together for at least one second: the message C.O.S.t. will be
displayed.
Press than repeatly CLEAR until interested variable's message is displayed
(see table below) : variable value and related message will be displayed.
Press + or - to set a new value and then CLEAR to confirm.
The next system constant will then appear.
You can press CLEAR for a least two second to escape and return to the Run
Mode
M
e
s
. s
V
a
u l
e
E t
n
P
=
1
e T
m
p
e
a r
u t
e r
e r
p
e r
s
. 0
° 0
A
. d
E t
°
C
n I
p
t u
e t
m
p
e
a r
u t
e r
*1) tEnP =1 : °C Temperature range.
tEnP =2 : °F Temperature range.
*2) You can correct the readings on the various sensors (+ or -).
M
e
a
n
n i
g
e
t n
t a
o i
n
= (
° 1
, C
=
° 2
) F
s
e
s n
r o
c
r o
e r
t c
o i
n
+ (
o
) -
Thermometer with recorder
MAIN SETTINGS (Run Mode).
MAXIMUM TEMPERATURE RECORDING VIEW.
Press + :
This message will be displayed followed by
° Maximum temperature recording.
MINIMUM TEMPERATURE RECORDING VIEW.
Press + :
This message will be displayed followed by
° Minimum temperature recording.
MEMORY CLEAR.
Press CLEAR for more two seconds:
This message will be composed on display before
clearing operation.
COSt PROGRAMMING (System constants)
These settings refer to the mode operation of the system and must be made on
initial start-up.
Press - / + together for at least one second: the message C.O.S.t. will be
displayed.
Press than repeatly CLEAR until interested variable's message is displayed
(see table below) : variable value and related message will be displayed.
Press + or - to set a new value and then CLEAR to confirm.
The next system constant will then appear.
You can press CLEAR for a least two second to escape and return to the Run
Mode
N
o
e t
M
e
s
. s
V
a
u l
e
*
) 1
E t
n
P
=
1
e T
m
*
) 2
. 0
° 0
A
. d
E t
°
C
*1) tEnP =1 : °C Temperature range.
tEnP =2 : °F Temperature range.
*2) You can correct the readings on the various sensors (+ or -).
HP10
SL 3.0
Handbook
M
e
a
n
n i
g
p
e
a r
u t
e r
e r
p
e r
s
e
t n
t a
o i
n
= (
° 1
, C
=
° 2
n I
p
t u
e t
m
p
e
a r
u t
e r
s
e
s n
r o
c
r o
e r
t c
o i
n
N
o
e t
) F
*
) 1
*
) 2
+ (
o
) -
Advertisement
Table of Contents
Summary of Contents for POLA HP10
- Page 1 HP10 HP10 SL 3.0 SL 3.0 Thermometer with recorder Thermometer with recorder Handbook Handbook MAIN SETTINGS (Run Mode). MAIN SETTINGS (Run Mode). MAXIMUM TEMPERATURE RECORDING VIEW. MAXIMUM TEMPERATURE RECORDING VIEW. Press + : Press + : This message will be displayed followed by This message will be displayed followed by °...
- Page 2 Ad.tE=0.0 tEnp=1 Ad.tE=0.0 INSTALLATION INSTALLATION How to connect the line How to connect the line HP10 HP10 Connect 230V line on terminals L-N. Connect 230V line on terminals L-N. Protect supply with adequate fuse. Protect supply with adequate fuse.
Need help?
Do you have a question about the HP10 and is the answer not in the manual?
Questions and answers