Hot Wheels B610S Instruction Manual

B1964-0920G1 DAREDEVIL CHALLENG 2/21/03 9:55 AM Page 1
hotwheels.com
INSTRUCTION MANUAL
Keep these instructions
for future reference, as they contain important information.
START HERE!
Follow the step-by-step instructions to set up your race set.
Please separate the "Assembly Map" page, and keep it
handy during assembly. This page contains the contents
list and large-scale Layout Drawings of the fully-assem-
bled track. You'll probably need to refer to it as you go.
The Assembly Map looks like this:
2
1
C
1 x 9" TERMINAL TRACK 4 x 9" STRAIGHT 4 x 6" STRAIGHT 3 x 15" STRAIGHT 7 x 9" RADIUS CURVE
1 x SANDPAPER 12 x GUARDRAILS 2 x CONTROLLERS 4 x CRADLES 1 x WALL POWER PACK
Track layout dimension is 4' 3" x 3' 6"
L L
C C
T T
T T
F
4 J
3 B
B
2
6
4
D
B
H
H
G J
F T
T
T T H
D
H
5 T
T
3 T
5
T
D
4
C J
F 1 B 1
H
H
H
H
F F
C
2
4
F
J F
A
S
G
Look for this symbol
cates important information.
Be sure to check out the Troubleshooting Guide on
the back of the Assembly Map.
I. BASIC TRACK ASSEMBLY
Start out on a clean, hard, flat racing surface – not carpet-
ing. Take out all the track pieces (and other parts) and
check them carefully against the contents list on the
Assembly Map.
This track features a Cliff Hangers
lets you race up the wall. So make sure you've chosen
an assembly location with a wall surface handy.
B1964-0920G1
G
H J S
2 x 9" RADIUS 1/8 2 x 9" RADIUS 1/4 12 x TRANSITION TRACK
8 x 9" RADIUS BANK 4 x 12" RADIUS 1/8 1 x 15" SQUEEZE
CURVE DBL RAIL
TRACK
1 x CARDBOARD 2 x LARGE CLIPS
1 2 3 4 5 6
2 x VEHICLES 2 x #1 SUPPORTS 3 x #2 SUPPORTS 2 x #3 SUPPORTS 4 x #4 SUPPORTS 2 x #5 SUPPORTS 1 x #6 SUPPORTS
2
B1964-0921
©2002 Mattel, Inc. CHINA
throughout this manual. it indi-
vertical section that
®
CAUTI O N - ELECTRI C TOY:
NOT RECOMMENDED FOR CHILDREN UNDER 8 YEARS OF
AGE. AS WITH ALL ELECTRIC PRODUCTS, PRECAUTIONS
SHOULD BE OBSERVED DURING HANDLING AND USE TO
PREVENT ELECTRIC SHOCK. MODEL B610S:
INPUT: 120VAC, .10A, 60 HZ ONLY. OUTPUT: 14.0VDC,
0.35A, 4.9VA.
1.
There are letters molded into each track piece. These
letters are used in these instructions to indicate which
track piece goes where. Following the layout drawings
on the Assembly Map, you may want to lay out your
track – without connecting any track pieces. That way
you'll be able to see how the track layout goes together.
2.
To connect track pieces:
working on the flat surface,
push the ends of the track
pieces together. Make sure
they snap together securely
– you'll hear a click when
they're properly connected. Remember: if the track con-
nections aren't right, electric power won't flow from one
track section to the next.
3.
To disconnect track pieces, sim-
ply reach underneath where the
track pieces meet and press the
locking tabs together with thumb
and forefinger as shown.
Occasionally the metal track rails will stick up too far
from the surface of a track piece, as shown. This may
interfere with vehicle movement. To correct, simply
press the rail back down with your finger. If the prob-
lem persists, please contact Customer Service toll-
free at 1-888-557-8926 (see hours of operation in the
Warranty section).
Sometimes brand-new track may need a quick clean-
ing for best performance. Check the Maintenance
section of this manual for more information.