Advertisement
Quick Links
Ion+
®
Connect
Digital Level Control Switch With Alarm
Introduction
The Ion+ Connect is a residential sump/sewage ejector
pump controller equipped with the revolutionary Ion
level sensor and integrated cellular texting module.
The device will run a manual pump up to 12 FLA,
can sense up to 72" of water, has customizable start/
stop/alarm levels, and provides alarm notifications via
SMS text for alarms like high water, pump fail, power
fail, and many more.
What's in the Box
The Ion+ Connect comes with:
1. Ion+ Connect
Pump Controller equipped with 10' 115 VAC
15A cord
2. Ion Sensor with pipe clamp
Connects to Ion+ Connect to provide level
signal
1
Connec
W W W . I O N P R O D U C T S . N E T
POWER PUMP ALARM
CELL
INPUT:
120VAC 60HZ 15A
OUTPUT:
120VAC 60HZ 12FLA 72LRA
PUMP
TEST
SILENCE/
PATENTS PENDING
RESET
PATENT NO. 8,591,198
LOCK/
UNLOCK
REMOTE
DIGITAL
REMOTE
ALARM
LEVEL
ALARM
INPUT
SENSOR
CONTACT
www.ionproducts.net
2
OPERATION MANUAL
Dated: 07/18/2017
Document Name: Ion+Connect_OM
Features
The following illustration describes the physical
features of your Ion+ Connect.
®
1. Power LED
Indicates the power status of unit
Refer to the LED section for details
2. Pump LED
Indicates the pump status
Refer to the LED section for details
3. Alarm LED
Indicates alarm status
Refer to the LED section for details
4. Cell LED
Indicates cellular status
Refer to the LED section for details
5. Pump Test
Hold down button for 5 seconds to manually
run pump
6. Silence / Reset
Momentarily push for Alarm Silence
Hold to reset unit
7. Lock / Unlock
Press for approximately 3 seconds to
unlock unit to accept SMS/text configuration
commands
Page 1 of 12
1
2
3
4
5
6
7
10
8
9
Advertisement
Summary of Contents for Ion Technologies Ion+ Connect
- Page 1 Features The following illustration describes the physical features of your Ion+ Connect. Introduction The Ion+ Connect is a residential sump/sewage ejector pump controller equipped with the revolutionary Ion ® level sensor and integrated cellular texting module. The device will run a manual pump up to 12 FLA, can sense up to 72”...
-
Page 2: Installation
Document Name: Ion+Connect_OM Page 2 of 12 Press again after unlock to lock unit from f. Plug pump and Ion Sensor into Ion+ Connect. accepting SMS/text configuration commands Note: The included Ion digital water level sensor has 8. Digital Water Level Sensor a 72”... - Page 3 Plug the Ion+ Connect into a dedicated AC outlet. installation requires the sensor be mounted to the pipe, the pipe-mount bracket is sold separately, PN: Once it is powered on, the Ion+ Connect will attempt IN-SPB1-1. to connect to the cellular network.
- Page 4 5. Configure the Name of Your Ion+ Connect You can give your Ion+ Connect a name that it uses in the notification messages it sends. a. On your cell phone, compose a new text message to your Ion+ Connect’s phone number.
- Page 5 Ion+ Connect to ensure you are always 1. Test Your Pump protected. You can test your Ion+ Connect at any time by pressing the “Pump Test” button. a. Holding Pump Test will manually run pump. b. Holding it for 3 seconds will send a notification to those in the list.
-
Page 6: Commands Summary
Commands Summary These are the commands accepted by the Ion+ Connect. Note that the commands under the Admin Settings section will only be accepted if the unit is first unlocked by holding the UNLOCK button on the faceplate until it beeps twice. - Page 7 OPERATION MANUAL Ion+ ® Connect Dated: 07/18/2017 Digital Level Control Switch With Alarm Document Name: Ion+Connect_OM Page 7 of 12 Command Syntax Description alarm batt low alarm batt low 3.9 Sets the value in volts for low battery threshold alarm level high alarm level high 8 Sets the value in inches for high level threshold alarm level low...
- Page 8 Ion+ Connect OPERATION MANUAL ® Dated: 07/18/2017 Digital Level Control Switch With Alarm Document Name: Ion+Connect_OM Page 8 of 12 LED Explanations Power LED Condition Normal battery ok, AC ok Solid GREEN battery charging, AC ok Blinking GREEN (1s on, 1s off) Trigger alarm Loss of power Blinking AMBER (0.1s on, 0.9s off)
-
Page 9: Optional External Connections
Monitored to Monitor by Ion+ Connect Ion+ Connect Either circuit inside the Ion+ Connect may be configured via cellular phone to be normally open or normally closed (see Command Summary). 15.21 Information to User Changes or modifications not expressly approved by Metropolitan Industries will void the user’s authority to operate the equipment. - Page 10 Ion+ Connect OPERATION MANUAL ® Dated: 07/18/2017 Digital Level Control Switch With Alarm Document Name: Ion+Connect_OM Page 10 of 12 Notes www.ionproducts.net...
- Page 11 OPERATION MANUAL Ion+ ® Connect Dated: 07/18/2017 Digital Level Control Switch With Alarm Document Name: Ion+Connect_OM Page 11 of 12 Notes www.ionproducts.net...
- Page 12 Coverage and Term. Metropolitan Industries, Inc. (“Metropolitan”) warrants to the original purchaser (the “Buyer”) of each Ion Technologies product (the “product”), that any part thereof which proves to be defective in material or workmanship within one (1) year from date of manufacture, will be replaced at no charge with a new or remanufactured part, F.O.B.
Need help?
Do you have a question about the Ion+ Connect and is the answer not in the manual?
Questions and answers