Table of Contents
Advertisement
Quick Links
IVC-100/100G & IVC-200/200G
& IVC-120/120G & PM-1056
User Manual Version 2.10
February, 2012
©Copyright 2003 by ICP Electronics Inc. All Rights Reserved.
The information in this document is subjected to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Trademarks
PM-1056 is a registered trademark of ICP Electronics Inc. IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a registered
trademark of Intel Corporation. Other product names mentioned herein are used
for identification purpose only and may be trademarks and/or registered
trademarks of their respective companies.
1
Advertisement
Table of Contents
Summary of Contents for ICP Electronics IVC-100G
- Page 1 Trademarks PM-1056 is a registered trademark of ICP Electronics Inc. IBM PC is a registered trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Other product names mentioned herein are used for identification purpose only and may be trademarks and/or registered trademarks of their respective companies.
-
Page 2: Table Of Contents
Installation Procedures ........... 15 Driver Installation ..............15 Check for Installed Driver ............18 Demo Programs............20 Video Image Preview for IVC-100G/100........20 Video Image Preview for IVC-200G/200........22 Video Image Preview for IVC-120G/120........22 Recording the Captured Image ..........25 Uninstalling the Program ........ -
Page 3: Product Introduction
PM-1056 video capture cards. These cards enable users to capture live video from video source such as the CCTV camera. These cards are PCI compliant. IVC-100G/100 and IVC-200G/200 have four video input channels and an LED indicator. VC-120G/120 has 16 channels and an LED indicator. This unique LED feature makes IVC-100G/100, IVC-200G/200 and IVC-120G/120 &... -
Page 4: Common Features For Ivc-120G/Ivc-120
GPIO module: GPIO daughter board x 1, flat cable x 1, input connector x 1 and output connector x 1 (for IVC-100G, IVC-200G and IVC-120G only) • Video connector cable with 16 video inputs and 1 video output x 1... -
Page 5: Notes
OS: Windows 98 SE, Windows ME, Windows 2000 and Windows XP Notes • IVC-100G/100/200G/200/120G/120 will take up a set of IRQ and I/O Address. Please make sure there is a free set of IRQ and I/O address for IVC-100 to use. The IRQ of the PCI slot can be modified from the CMOS setting of the motherboard. -
Page 6: Hardware Connections & Settings
2. Hardware Connections & Settings 2.1 Illustration for Video Capture Card IVC-100G GPIO = general purpose input output GPIO pin connector Jumper BNC connector IVC-100 Jumper BNC connector IVC-200G GPIO = general purpose input output GPIO pin connector BNC connector... - Page 7 IVC-200 BNC connector Jumper IVC-120G GPIO = general purpose input output GPIO pin connector Jumper Connector IVC-120 Jumper Connector...
-
Page 8: Connections To The Video Source
2.2 Connections to the Video Source Connect your video source to the BNC connector of the video capture card. Take IVC-100G and IVC-120G for example: • IVC-100G Video Source • IVC-120G x 16 Video Source... -
Page 9: Led Jumper Settings
2.3 LED Jumper Settings The jumper setting controls the card number on the LED. Jumper Setting Table Logic 1 = ON Logic 0 = OFF Card Number on the LED... -
Page 10: General Purpose Input Output (Gpio) Connections
2.4 General Purpose Input Output (GPIO) Connections Please note that this section ONLY applies to IVC-100G, IVC-200G and IVC-120G. The GPIO module contains a flat cable, a GPIO daughter board, an input connector and an output connector. The GPIO module enables users to connect four input devices and four output devices. - Page 11 2.4.1 Connections to GPIO daughter board Connect the flat cable to the GPIO pin connector on IVC-100G (IVC-200G and IVC-120G). IVC-200G Flat cable GPIO pin connector GPIO pin Flat cable connector IVC-100G GPIO pin connector Flat cable IVC-120G...
- Page 12 Connect the other end of the flat cable to the GPIO pin connector on the GPIO daughter board. GPIO pin connector GPIO daughter board Use the screw to secure the GPIO daughter board on your computer case. 2.4.2 Connections for Input/Output devices An input connector and an output connector are provided for connections to the external devices.
- Page 13 Common 1 Normal Open 1 Normal Close 1 Common 2 Normal Open 2 Normal Close 2 Common 3 Normal Open 3 Normal Close 3 Common 4 Normal Open 4 Normal Close 4 Output Connector Figure 2 Specification for General Inputs The general inputs can take DC voltage from 0-24V.
- Page 14 Relay Coil Specification Coil voltage Nominal Voltage Nominal Current Coil Resistance Power (VDC) (mA) (Ohm) Consumption (W) 66.7 About 0.36W Relay Coil Specification (Continue) Pull-in Voltage Drop-out Max-Allowable (VDC) Voltage (VDC) Voltage (VDC) 75% max. 10% min. 110% 3.75V 0.5V 5.5V After connecting the external device, plug the connector into the GPIO board.
-
Page 15: Installation Procedures
3. Installation Procedures 3.1 Driver Installation IEI driver installation program makes the driver installation of multiple cards an easy job. The steps of driver installation are described as below: Steps: i. Adjust the jumper setting of the video capture card. ii. - Page 16 ix. For multi-card system, you will be asked to install video and audio drivers for every card in your system. Click Yes to continue the installation. x. After the driver has been successfully installed, click Finish.
- Page 17 xi. Restart your computer when you finish installing DirectX. You can also install a driver first before plugging the video capture card into the computer. After that, install DirectX and then shut down the computer. Adjust the jumper setting of the video capture card and plug the video capture card into the computer.
-
Page 18: Check For Installed Driver
Check for Installed Driver If you have any doubt about whether the driver is properly installed or not, follow the steps below: 1. Right click My Computer and click Properties. 2. Choose Hardware. Then click on Device Manager. Double click the mark “Sound, video and game controllers”. You should be able to see a list of the audio and video driver of each video capture card. - Page 19 For Window 98, Win ME, if system requires the file for driver, you can find the file (ieibt878.exe) in your CD, under the directory Windows/Driver.
-
Page 20: Demo Programs
4. Demo Programs Video Image Preview for IVC-100G/100 To preview a video image, follow the steps below: i. Double click Demo folder. ii. Double click ivc-100.exe. iii. Click Select Device to choose the video capture card. iv. Click Video Size to choose the resolution. The available resolutions... - Page 21 v. Click Video Channel to activate the video input channels. Disable the channels without input signals. For example, if there is only one CCTV camera connected to Channel 1, users are recommended to enable that channel only and disable all the others in order to reach a high quality display image.
-
Page 22: Video Image Preview For Ivc-200G/200
Video Image Preview for IVC-200G/200 i. Double click “Demo” folder. ii. Double click “ivc-200.exe”. iii. Click “Select Device” to choose the video capture card. iv. Click “Video Size” to choose the resolution. The available resolutions are 160 x 120 and 320 x 240. v. - Page 23 iv. Click Video Size to choose the resolution. The available resolutions are 160 x 120 and 320 x 240. v. Click “Video Channel” to activate the video input channels. Disable the channels without input signals. For example, if there is only one CCTV camera connected to Channel 1, users are recommended to enable that channel only and disable all the others in order to reach a high quality display image.
- Page 24 vi. Click GPIO to control the input/output devices. vii. Click VPD to view or edit the serial number for this card.
-
Page 25: Recording The Captured Image
viii. Click Output to select a channel to output. Recording the Captured Image The program used in the following section is amcp.exe. It is a program of Microsoft for video capturing. i. Open the folder Demo and double click amcap.exe. ii. - Page 26 v. Click Capture then Start Capture. vi. Set the directory and folder to save the captured file. Then click OK to start recording the video image. vii. Click Stop Capture to stop recording.
-
Page 27: Uninstalling The Program
5. Uninstalling the Program i. Click Start then choose Settings and double click Control Panel. ii. Double click Add/Remove Programs. iii. Select the software of Video Capture Card and click Add/Remove. iv. Click Yes to uninstall the Video Capture Card software. Select “Restart my computer now”... -
Page 28: Appendix A: Watch Dog Function Of Ivc-200G-Wdt
Appendix A: Watch Dog Function of IVC-200G-WDT IVC-200G-WDT Installing the Hardware Connect to Reset Pin on the motherboard Connect to chassis’s reset button on the right. Instructions • Run wdt-demo.exe in the Demo folder. The following dialog will appear on the screen. - Page 29 • When the option “Refresh WDT automatically to prevent from rebooting” is not selected as shown in the picture below, the system will reboot after one minute once you have applied the “Enable WDT with time-out period 1 minute” option. •...
-
Page 30: Appendix B: Pm-1056 Hardware Diagrams
Appendix B: PM-1056 Hardware Diagrams PM-1056-16PG... - Page 31 PM-1056-16P...
- Page 32 PM-1056-4PG/4PGB...
- Page 33 PM-1056-4P/4PB...
- Page 34 The driver program and operation of PM-1056-16P/PG and IVC-120/G are the same. PM-1056-16P/PG is the interface of PC/104-PLUS. The driver program and operation of PM-1056-4P/4PB/4PG/4PGB and IVC-100/G are the same. PM-1056-4P/4PB/4PG/4PGB is the interface of PC/104-PLUS. PCI Signal Grouping Selection •...
-
Page 35: Appendix C: How To Set Sw1 Of The Pm-1056 When Using R20
Appendix C: How to Set SW1 of the PM-1056 when Using R20 and R21 Version in One System If using PM-1056-R20 and PM-1056-R21 together in one system (four cards in total), please refer to the following table to setup the SW1 rotary switch. Quantity of PM-1056 Version SW1 Rotary Switch Position...