Subscribe to Our Youtube Channel
Summary of Contents for LOFTNESS Kwik Trim 53
- Page 1 Kwik Trim 53 Owner’s Manual and Parts Book (Originating w/Serial Number 64-142 thru 64-147) Model Number: Serial Number: Date of Purchase: N38422 Rev. B 02.28.17...
- Page 3 All Loftness products have a one (1) year limited warranty. The XLB10 Grain Bag Loader has a two (2) year limited warranty. If any Loftness product is used as rental equipment, or in a commercial application, the limited warranty period is for only 30 days from the delivery date to the original customers.
-
Page 9: Table Of Contents
Loftness Serial Number ........ - Page 10 Motor Assembly (N24594) ........... . . 48 Kwik Trim 53...
- Page 11 Metric Hardware and Lock Nuts ..........80 Kwik Trim 53...
- Page 12 Kwik Trim 53...
-
Page 13: Introduction
Introduction Owner Information Serial Number Location Thank you for your decision to purchase a Kwik Trim 53 Loftness Serial Number from Loftness. To ensure maximum performance of your machine, it is mandatory that you thoroughly study the owner’s manual and follow its recommendations. Proper operation and maintenance are essential to prevent injury or damage and to maximize machine life. -
Page 14: Manual Storage
Constantly watch the terrain ahead for sudden changes in slopes or obstacles such as rocks, logs, or stumps that may cause loss of stability, resulting in tip-over or roll-over. Kwik Trim 53... -
Page 15: Operating Position
Fully adjustable seat. Weight • Standard with AM/FM radio (MP3 jack). • Cup holder. • 14,000 lb. (6,350 kg) Engine • The quiet, efficient 47.6 HP diesel engine uses less than 1.6 gal. (6.05 l) of fuel per hour. Kwik Trim 53... -
Page 16: Operating Ranges
See “Extending and Retracting the difficult cut possible. 35° left or right operating range. Saw Blade” on page 15 for operation instructions. See “Tilting the Mast” on page 16. Kwik Trim 53... -
Page 17: Kwik Trim Identification
Introduction Kwik Trim Identification Kwik Trim shown in transport mode. Blade Motor Boom Boom Sensor Lift Sensor Hose Reel Lift Cylinder Saw Blade Tilt Cylinder Winch Dozer Blade Kwik Trim 53... - Page 18 Kwik Trim 53...
-
Page 19: Safety Instructions
Contact Loftness for safety decal and in the owner’s manual. When you see this replacement. symbol, be alert to the possibility of personal... -
Page 20: Safety Rules
Do not replace components or parts with other than factory-recommended service parts. To do so may • Never check for leaks by using any part of your body decrease the effectiveness of the machine. to feel for escaping fluid. Kwik Trim 53... -
Page 21: Emergency Evacuation - Safety Windows
To remove the window from the outside, locate and grab the end of the rubber locking strip (2) and pull out. Grab and lift the window out of the frame. WARNING: Do not try to push the window Kwik Trim 53... - Page 22 Always maintain a safe or death. separation from utility lines. Consult utility company Part No. N28462 Do not use for lifting, before trimming. lowering or Keep boom clean and transporting people. free of debris. Part No. N28464 Part No. N28461 Kwik Trim 53...
- Page 23 Safety Instructions Safety Decal Locations (Cont’d) WARNING SKIN PUNCTURE HAZARD. HYDRAULIC LINES. Protect hands and body from high pressure fluids. N23506 Part No. N23506 Kwik Trim 53...
- Page 24 Kwik Trim 53...
-
Page 25: Operating Instructions
Do not jump. Adjust the seat belt so the belt is over the operator’s hips. Fasten the seat belt snugly. Lower the left control lever (1) console. Close cab door. Start the engine. Kwik Trim 53... -
Page 26: Hydraulic Controls
NOTE: An extend/retract sensor locks and unlocks the boom assembly. boom raise/lower functions on the foot control. Retract the boom assembly until the boom stops. NOTE: Once the sensor contacts the top of the boom, raise/lower functions are deactivated. Kwik Trim 53... -
Page 27: Raising And Lowering The Boom
Pull the left joystick backward (2) to shorten the reach of the saw blade. Push the right joystick forward (1) to lower the boom. Pull the right joystick backward (2) to raise the boom. Kwik Trim 53... -
Page 28: Tilting The Mast
Turn throttle knob (3) right to increase engine RPM. Turn the knob left to decrease engine RPM. NOTE: It is recommended to operate the Kwik Trim at NOTE: Saw blade rotates in a forward cutting direction. full RPM (throttle). Kwik Trim 53... -
Page 29: Dozer Blade
LEVERS IN FREE-SPOOL POSITION To unwind the winch cable, turn the top and bottom lever to the “FREE” position. Push the “IN” button (1) to wind the winch cable. Push the “OUT” button (2) to unwind the winch cable. Kwik Trim 53... -
Page 30: Blade Angle Adjustment
10 ft. (3 m) of power cables must be done by trained and Replace and tighten fasteners. experienced line-clearance tree trimmers. Remove motor mount jig. WARNING: Always have an operator in the operator’s seat while the machine is in operation. Kwik Trim 53... - Page 31 NOTE: Avoid rubbing the boom on lower limbs while working up the tree. Rubbing the boom on the tree or limbs will result in damage to the boom and structural weaking of the boom. Kwik Trim 53...
-
Page 32: Operating The Kwik Trim On A Slope
Saw Blade” on page 15 Fully retract the boom. Refer to “Extending And Retracting the Boom from and to Transport Position”, and “Retracting Boom to Transport Position” on page Raise the dozer blade. See “Dozer Blade” on page 17. Kwik Trim 53... -
Page 33: Service Steps
(3) from the upper hole. Fold step down, reinsert the pin (2) into the lower hole and secure with the retaining clip (3) as shown. IMPORTANT: Return service step to its storage position when finished. Kwik Trim 53... -
Page 34: Loading And Unloading
• Never change courses on the ramps. • Do not slew on the ramps. The machine may tip over. • When slewing on the truck bed, do it slowly as the footing may be unstable. Kwik Trim 53... -
Page 35: General Maintenance
And with boom fully extended, four on the right side (3) and four on the left side (4). If any bolts are loose, remove the bolt and add high- strength Loctite to threads. Reinsert bolt and tighten. ® Kwik Trim 53... -
Page 36: Lubrication
Lubrication Grease Points Boom Pivot, right Boom Cylinder, upper Boom Pivot, left Boom Cylinder, lower Mast Pivot Mast Cylinder, upper Dozer Cylinder, rear Mast Cylinder, lower Dozer Cylinder, front Slew Drive Dozer Pivot, right Dozer Pivot, left Kwik Trim 53... -
Page 37: Releasing Hydraulic Pressure
Interval: Every 50 hours of operation. • Dozer Lift Cylinder Location: Rod end (7); base end (8). Interval: Every 50 hours of operation. • Dozer Pivot Location: Left (9) and right (10). Interval: Every 50 hours of operation. Kwik Trim 53... -
Page 38: Saw Blade
Inspect the saw blade teeth (1) for wear or damage after eight hours of operation or daily. Replace or sharpen if necessary. Inspect the blade guard (2) for damage. NOTE: The industry standard 24 in. (609.6 mm) carbide- tipped saw blade teeth can be re-sharpened. Kwik Trim 53... -
Page 39: Boom
If during the di-electric test, the return current is Structural repairs should be referred to Loftness for close to 1000 micro-amps, stop the test immediately and a case by case study. -
Page 40: Troubleshooting
12 volts is being supplied. Black power wire from inside cab (in panel below seat) to switch black wire. Blue wire on switch to red wire on solenoid. Faulty sensor switch. Replace sensor switch. Faulty solenoid. Replace solenoid. Kwik Trim 53... - Page 41 Saw blade bearing damaged. Replace bearing. Motor for saw has leak. Shaft seal on motor has blown. Check return oil lines for possible pinched hose and replace shaft seal. NOTE: See the machine’s “Owner’s Manual” for additional troubleshooting procedures. Kwik Trim 53...
- Page 42 Kwik Trim 53...
-
Page 43: Parts Identification And Hydraulic Schematics
Parts Identification PARTS IDENTIFICATION AND HYDRAULIC SCHEMATICS Kwik Trim 53... -
Page 44: Kwik Trim Assembly
Parts Identification Kwik Trim Assembly 17 (inside) Kwik Trim 53... - Page 45 HYDRAULICS (See page 50) N38356 COVER PLATE (See page 71) N105428 WINDOW, ESCAPE (See page 67) N105416 WINDOW, RIGHT (See page 66) INCLINOMETER, 3.5 X 1.6 45DEG N118561 (Both inside. One on front panel and one on side panel.) Kwik Trim 53...
-
Page 46: Mast, Boom Mount
Parts Identification Mast, Boom Mount 19 17 16 15 Kwik Trim 53... - Page 47 N22358 BOLT, #10-32 X 3/4" BHCS 4460 WASHER, 1/4" SAE FLAT 4000 BOLT, 1/4" X 1" GRADE 5 N38126 NIPPLE, 1/8 X 3 N38128 COUPLING, 1/8 PIPE N17007 GREASEZERK, 1/8" NPT N118559 INCLINOMETER, 6.4 X 2.9 50DEG Kwik Trim 53...
-
Page 48: Boom Assembly (N38189)
BOOM ASSEMBLY (See page 40) N24496 TUBE, W/SLIDES INNER (See page 44) N38192 TUBE, OUTER W/SLIDES (See page 43) N24810 SCREW, FHCS 3/8-16 UNC X 1-1/4 N38189 BOOM ASSEMBLY (See page 38) N38189 BOOM ASSEMBLY (See page 37) Kwik Trim 53... - Page 49 PART # DESCRIPTION N24850 MOUNT, WELDMENT TRUNNION N24629 CYLINDER, 2" BORE 72" STROKE N28746 CYLINDER, 2-1/2" X 175" STROKE 4011 BOLT, 1/2" X 1" GRADE 5 N16472 WASHER, 1/2 NORDLOCK N38323 PLATE, CYLINDER BOOM N38212 PLATE, CYLINDER BOOM Kwik Trim 53...
-
Page 50: Boom Assembly (N38189) (Cont'd)
Parts Identification Boom Assembly (N38189) (Cont’d) 4,19 *Item 18 (N28614), Roller Assembly Kwik Trim 53... - Page 51 MOUNT, BOOM GLUED ASSY N24620 ROD, HOSE SUPPORT N28272 BUSHING, 1.01ID X 1.25ODX.682 N24490 PIN, 1.25 X 4.125 N28614 ROLLER, ASSY FAIRLEAD N28701 ROLLER, 2" HANNAY FAIRLEAD N28702 ROLLER, 2.5" HANNAY FAIRLEAD 4064 WASHER, FLAT 3/8" N149618 GUIDE, HOSE Kwik Trim 53...
-
Page 52: Boom Assembly (N38189) (Cont'd)
Parts Identification Boom Assembly (N38189) (Cont’d) QTY. PART # DESCRIPTION N24594 MOTOR ASSEMBLY (See page 48) 4011 BOLT, 1/2" X 1" GRADE 5 N31760 JIG, KWIK TRIM MOTOR MOUNT N16472 WASHER, 1/2 NORDLOCK 4250 NUT, STANDARD 1/2 Kwik Trim 53... -
Page 53: Jig, Motor Mount (N31760)
PLATE, KWIK TRIM JIG INNER N31763 PLATE, KWIK TRIM JIG BOTTOM R N31221 PIN, 3/8" X 2-1/4" RETAINER 4052 NUT, LOCK 3/8" N31741 WASHER, FLAT 3/8" SAE 4064 WASHER, FLAT 3/8 4537 BOLT, 3/8" X 2-1/4" GRADE 5 Kwik Trim 53... -
Page 54: Outer Tube Assembly (N38192)
Parts Identification Outer Tube Assembly (N38192) Kwik Trim 53... - Page 55 N24475 TUBE, BOOM OUTER 4011 BOLT, 1/2" X 1" GRADE 5 4054 NUT, LOCK 1/2" TOP N24502 DEFLECTOR, WELDMENT N121215 PLATE, CLAMP DEFLECTOR N24491 SLIDE, .50" X 4.25" X 24" N24492 SLIDE, .50" X 6.25" X 24" Kwik Trim 53...
-
Page 56: Tube, W/Slides Inner (N24496)
SLIDE, 0.50" x 4.25" x 20" N24495 SLIDE, 0.50" x 6.25" x 14" N24807 PLATE, EXTENDER BULKHEAD N24680 BOLT, 3/8 x 3/4" BHCS N24809 BOLT, FHCS 3/8" x 1" N24624 MOUNT, WELDMENT BULKHEAD N24659 SLIDE, 0.50" x 4.25" x 24" Kwik Trim 53... -
Page 57: Clamp, Cradle Top W/Slides (N38185)
Parts Identification Clamp, Cradle Top w/Slides (N38185) Underside of clamp shown for clarity. QTY. PART # DESCRIPTION 4011 BOLT, 1/2" X 1" GRADE 5 N38186 CLAMP, BOOM TOP WELDMENT N24509 PLATE, SLIDE SIDE N24508 PLATE, SLIDE TOP Kwik Trim 53... -
Page 58: Cradle Assembly (N38178)
SLIDE, CLAMP SIDE N24505 SLIDE, BOTTOM TRANSPORT 4431 SCREW, FLAT HEAD CAP 1/2" X 1-1/2" N55297 PLATE, SLIDE SIDE N38179 CRADLE, WELDMENT N24638 SLIDE, BOTTOM TRANSPORT N22210 SCREW,3/8-16 X 3/4 SCKT HD SET 4105 GREASE-ZERK, 1/4" SCREW-IN Kwik Trim 53... -
Page 59: Step
QTY. PART # DESCRIPTION 4375 PIN, ROLL 3/16" X 1" N38295 PIN, 1/2 X 7.00 N38316 PIN, PIVOT STEP N38090 CLIP, HAIRPIN 5/32" X 2-1/2" N38294 BRACE, STEP N38290 STEP, FOLD DOWN N55219 PIN, .50 X 5.9 Kwik Trim 53... -
Page 60: Motor Assembly (N24594)
RETAINING RING, 3 1/2"BD X.109 N24651 NUT, HEX 1-1/2 FINE 4054 NUT, LOCK 1/2" TOP N24556 MOTOR, VOAC 9.8CC (See page 49) N24558 PLATE, COVER MOTOR FORMED 4369 WASHER, 5/16" FLAT 4412 BOLT, 5/16" X 3/4" GRADE 5 Kwik Trim 53... -
Page 61: Motor (N24556)
Parts Identification Motor (N24556) QTY. PART # DESCRIPTION N24866 SEAL KIT (Includes Items 1, 2, 3, and 4) O-RING O-RING SHAFT SEAL SEAL N24867 KEY, 6 X 6 X 35 Kwik Trim 53... -
Page 62: Hydraulics
Parts Identification Hydraulics 19 (Hose Wrap) Detail Hose Clamps 16,17 Hose Clamps (Hose Wrap - (Hose Wrap) above and below bulkhead) (Hose Wrap - for tilt cylinder) Kwik Trim 53... - Page 63 CLAMP, DBL. 1/2" SUPP. HOSE N20226 BOLT, 5/16" X 4" GRADE 5 N21365 CLAMP, 3/8" DOUBLE HOSE N129313 HOSE, SLEEVE 2-1/2 X 62 N129323 SLEEVE, HOSE 2-1/2 X 154 N129321 SLEEVE, HOSE, 3 X 38 N129309 SLEEVE, HOSE 2-1/2 X 45 Kwik Trim 53...
-
Page 64: Hydraulics (Cont'd)
Parts Identification Hydraulics (Cont’d) DETAIL B DETAIL A DETAIL C DETAIL D Kwik Trim 53... - Page 65 ELBOW, 45 DEG - 6MJIC -6FJIC N38377 HOSE, 3/8 X 182 LG -6FJX-6FJX N23832 TEE, 6MJIC - 6MJIC - 6FJX SWIVEL N29078 ELBOW, 90 DEG - 6MJIC - 6FJIC N24773 TEE, 6MJIC-6MJIC-6MJIC N38419 HOSE, 3/8" X 151" -6FJIC -6FJC Kwik Trim 53...
-
Page 66: Hydraulics (Cont'd)
Parts Identification Hydraulics (Cont’d) DETAIL E Kwik Trim 53... - Page 67 N38375 HOSE, 1/2 X 24 LG -8FJX-8FJX N38339 ADAPTER, 8MJC - 12MOR AUXL HOSE, TAKEUCHI AUXL N38370 HOSE, 1/4 X 11 LG -6FJX-6FJX90 N38369 HOSE, 1/4 X 37 LG -6FJX-6FJX90 N37279 TEE, -6MJIC-6FJIC-6MJIC N34326 ADAPTER, -6MJIC -4FBSPP Kwik Trim 53...
-
Page 68: Hydraulics (Cont'd)
Parts Identification Hydraulics (Cont’d) 6 12 18,19 20 8 21 22 23 DETAIL F (two views) Kwik Trim 53... - Page 69 HOSE, 1/2 X 24 LG -8FJX-8FJX90 ARMH HOSE, TAKEUCHI ARMH BSWR HOSE, TAKEUCHI BSWR N38373 HOSE, 1/2 X 19 LG -8FJX-8FJX BOOR HOSE, TAKEUCHI BOOR BUCR HOSE, TAKEUCHI BUCR BUCH HOSE, TAKEUCHI BUCH N132118 ADAPTER, EXTEND MED -8MBSPP-8FBSPP Kwik Trim 53...
-
Page 70: Hydraulics (Cont'd)
ADAPTER, BULKHEAD -8MJIC -8MJIC N38380 HOSE, 1/2 X 209 LG-8FJIC-8FJC AUXL HOSE, TAKEUCHI AUXL AUXR HOSE, TAKEUCHI AUXR N38345 ADAPTER, 12MBSPP - 8FJIC N38381 HOSE, 1/2 X 108 LG-8FJIC-10FJC BOOH HOSE, TAKEUCHI BOOH BOOR HOSE, TAKEUCHI BOOR Kwik Trim 53... -
Page 71: Hydraulics, Winch
ELBOW, 45 DEG - 8MJC - 10MOR 4466 BOLT, 1/2" X 1-1/2" GRADE 8 N16472 WASHER, 1/2 NORDLOCK 4052 NUT, LOCK 3/8" N16470 WASHER, 3/8 NORDLOCK 4416 BOLT, 3/8" X 1-1/4" GRADE 5 FAIRLEAD N34766 CABLE, 3/8" X 100' (Extra cable, not shown) Kwik Trim 53... -
Page 72: Hydraulic Schematic - Lift, Tilt, Transport Cylinders
Parts Identification Hydraulic Schematic - Lift, Tilt, Transport Cylinders Kwik Trim 53... -
Page 73: Hydraulic Schematic - Boom And Saw
Parts Identification Hydraulic Schematic - Boom and Saw Kwik Trim 53... -
Page 74: Hydraulic Schematic, Winch
Parts Identification Hydraulic Schematic, Winch Kwik Trim 53... - Page 75 Parts Identification This page intentionally left blank. Kwik Trim 53...
-
Page 76: Windows; Front, Top And Left Side
Parts Identification Windows; Front, Top and Left Side Kwik Trim 53... - Page 77 BOLT, 5/16" X 1-1/4" GR 5 FULL THRD N38326 DOOR, SEAL RUBBER 1/4 N38050 DOOR 4203 BOLT, 5/16" X 1" GRADE 5 N38049 PANEL, POLY KWIK TRIM N28237 SCREW, 5/16 X 1 SELF TAPPING N38325 SIDE, SEAL RUBBER 1/4 Kwik Trim 53...
-
Page 78: Windows; Rear And Right Side
Parts Identification Windows; Rear and Right Side QTY. PART # DESCRIPTION N105428 WINDOW, ESCAPE REAR (See page 67) N38321 ESCAPE, SEAL RUBBER 1/4 N105416 WINDOW, RIGHT N28237 SCREW, 5/16 X 1 SELF TAPPING Kwik Trim 53... -
Page 79: Window, Escape (N105428)
GASKET, WINDOW REAR TOP 4051 NUT, LOCK 5/16" 4369 WASHER, 5/16" FLAT N105484 SEAL, RUBBER 1/4 N105472 PANEL, POLY KWIK TRIM 1141 BOLT, 5/16" X 1-1/4" GR 5 FULL THRD N107696 LOCK STRIP, WINDOW REAR N107694 GASKET, WINDOW REAR TOP Kwik Trim 53... -
Page 80: Top Cover Assembly (N129683)
Parts Identification Top Cover Assembly (N129683) Kwik Trim 53... -
Page 81: Top Cover Assembly (N38340)
SEAL, RUBBER TOP 1/2 N16472 WASHER, 1/2 NORDLOCK 4250 NUT, STANDARD 1/2 N38220 SEAL, RUBBER FRONT 1/2 N38360 SCREW, 3/8 X 1 3/4 SELF TAPPING N38060 COVER, SPACER RIGHT N38218 SEAL, RUBBER TOP PANEL 1/2 N38221 SEAL, RUBBER SIDES 1 Kwik Trim 53... -
Page 82: Blade And Track Cover
Parts Identification Blade and Track Cover *Item #2 is placed inside of tracks (2 places). QTY. PART # DESCRIPTION N38071 BLADE, WELDMENT TB260 N31829 COVER, KWIK TRIM Kwik Trim 53... -
Page 83: Cover Plate
PART # DESCRIPTION 4006 BOLT, 3/8" X 1-1/2" GRADE 5 N38355 WASHER, .44 X 3.50 X 10GA N38356 WELDMENT, MOUNT HYD N28237 SCREW, 5/16 X 1 SELF TAPPING 4203 BOLT, 5/16" X 1" GRADE 5 N38216 PLATE, COVER Kwik Trim 53... -
Page 84: Fire Extinguisher
FIRE EXTINGUISHER, ABC 10LB 4203 BOLT, 5/16" x 1 GR5 N16469 WASHER, 5/16 NORDLOCK N28329 MOUNT, BRACKET FIRE EXTINGUISHER 4369 WASHER, 5/16" FLAT 4051 NUT, LOCK 5/16" N38328 MOUNT, FIRE EXTINGUISHER N28820 SCREW, 5/16 X 3/4 SELF TAPPING Kwik Trim 53... -
Page 85: Machine Decals And Signs
Keep machine leveled Check and replace any worn, torn, hard to read or laterally while operating. missing decals on your machine. NOTE: To order a complete Kwik Trim 53 Decal Kit use Part No. N28463 part number N28465. WARNING Part No. N22763 Avoid serious injury, equipment and property damage. - Page 86 Part No. N28012 Part No. N151283 VEHICLE TEST WEIGHT: 14,000LBS STANDARDS MET ROPS: ISO3471, ISO12117-2, ISO8082-2 OPS: ISO8084 FOPS: ISO8083 FOR LOFTNESS KWIK TRIM 53 LOFTNESS 650 SOUTH MAIN STREET HECTOR, MN 55342 Part No. N28288 1 1 1 1 Model Number...
- Page 87 Parts Identification Machine Decals and Signs (Cont’d) Part No. N28576 Part No. N28503 Part No. N26972 Part No. N13518 Kwik Trim 53...
-
Page 88: Takeuchi Tb260 Filters
Cab Fresh Air Filter 05546-00025 N118128 Refer to the List of Consumables in the Maintenance section of the Takeuchi TB260 Operator’s Manual for the filter and element maintenance schedules. The schedules also include page references for replacement procedures. Kwik Trim 53... -
Page 89: Appendix
12,000 lbs. (5,443 kg) Capacity Rollover Protection ROPS/FOPS/OPS Certified Cab Windows 1/2 in. Tinted Polycarbonate Custom Full-view Tinted Polycarbonate Skylight with Guard Certifications Boom – ANSI A92-2 Category C ROPS - ISO3471, ISO12117-2, 8082-2 OPS - ISO8084 FOPS - ISO8083 Kwik Trim 53... -
Page 90: Dimensions
5 ft. 9 in. (1.75 m) Excavator Length (E) 11 ft. (3.35 m) Front Extension (with Boom Withdrawn) (F) 14 ft. 3 in. (4.34 m) Width (G) 6 ft. 7 in. (2 m) Weight 14,000 lbs. (6,350 kg) Kwik Trim 53... -
Page 91: Torque Specifications
(904 N•m) (350 N•m) (494 N•m) 213 ft.-lb. 275 ft.-lb. 547 ft.-lb. 708 ft.-lb. 773 ft.-lb. 1000 ft.-lb. 386 ft.-lb. 545 ft.-lb. (289 N•m) (373 N•m) (742 N•m) (960 N•m) (1048 N•m) (1356 N•m) (523 N•m) (739 N•m) Kwik Trim 53... -
Page 92: Torque Specifications (Cont'd)
(277 ft.-lb.) (358 ft.-lb.) (383 ft.-lb.) (495 ft.-lb.) (195 ft.-lb.) 411 N•m 531 N•m 648 N•m 839 N•m 897 N•m 1160 N•m 458 N•m (303 ft.-lb.) (392 ft.-lb.) (478 ft.-lb.) (619 ft.-lb.) (662 ft.-lb.) (855 ft.-lb.) (338 ft.-lb.) Kwik Trim 53... - Page 94 Loftness Specialized Equipment, Inc. 650 So. Main Street • PO Box 337 • Hector, MN 55342 Tel: 320.848.6266 • Fax: 320.848.6269 • Toll Free: 1.800.828.7624 Printed in USA © Loftness 2017...
Need help?
Do you have a question about the Kwik Trim 53 and is the answer not in the manual?
Questions and answers