Subscribe to Our Youtube Channel
Summary of Contents for BXB Electroics WMP-2100
- Page 1 PA S IGITAL YSTEM ANUAL ERIES BXB Electronics Co., Ltd. 6F.-1, No.288-5, Xinya Rd., Qianzhen Dist., Kaohsiung City 80673, Taiwan (R.O.C.) TEL：+886(7)9703838 FAX：+886(7)9703883 www.bxb.tw...
-
Page 2: Table Of Contents
A. Table of Contents Table of Contents ................... 2 Front panel description .................. 3 Operate instruction ..................5 1. Re-Start ......................5 2. Working status LED indicators ................ 5 3. All Call and All Clear ..................6 4. Single zone broadcasting ................7 5. -
Page 3: Front Panel Description
Video(1) B. Front panel description WMP-2100 Re-Start Voice Level Auto Manual Pass Monitor Level Reset 30 SEC Mic 1 Mic 2 Mic 3 Mic 4 Aux 1 Aux 2 Aux 3 Aux 4 Group Bass Treble Master ○ 1 Re-Start button ○... - Page 4 30 SEC：The security warning (beep sound) will stop in thirty seconds Reset：Reset to factory setting ○ Monitor and Intercom buttons Monitor output sounds Intercom function ○ Pre-mixer volume control Mic1~Mic4：6.3 Ø Microphone volume knobs, Mic1 has priority to broadcast Aux1~Aux4：Adjust Aux1~Aux4 volume. Aux1 is reserved for telephone broadcasting. Master：Adjust master volume Treble：Adjust treble volume Bass：Adjust bass volume...
-
Page 5: Operate Instruction
C. Operate instruction 1. Re-Start When main control unit malfunction due WMP-2100 to unknown reasons, press Re-Start to Re-Start Voice Level start again. The problem usually results from Auto Manual Pass instable voltage input. Installation of Monitor Level... -
Page 6: All Call And All Clear
Video 3. All Call and All Clear WMP-2100 WMP-2100 WMP-2100 All zones broadcasting Re-Start Re-Start Re-Start Voice Level Voice Level Voice Level All Call Auto Auto Auto Manual Manual Manual Pass Pass Pass Monitor Level Monitor Level Monitor Level Reset... -
Page 7: Single Zone Broadcasting
4. Single zone broadcasting Video WMP-2100 Re-Start Blank for zone title Voice Level Auto Manual Pass Monitor Level Reset 30 SEC Mic 1 Mic 2 Mic 3 Mic 4 Single zone select button Aux 1 Aux 2 Aux 3 Aux 4... -
Page 8: Group Broadcasting
LEDs will turn off WMP-2100 supports 8 groups of group broadcasting and every Extension control unit supports 8 groups as well. Therefore, you can have 24 groups at most. Please refer to instructions above for group setting. -
Page 9: Reset Groups
6. Reset groups Video 1. Press Group button(s) you want to make changes. (add/remove zones) Group Preset zone LEDs will turn on and Groups broadcasting/ setting (blue) indicate green 2. Select the zones which you want to remove When being pressed When being pressed the first time, the second time, the the LED will turn on and indicate... -
Page 10: Monitor And Intercom Function
7. Monitor and Intercom function Video WMP-2100 Select single zone to enable intercom Re-Start Voice Level Intercom is enabled when the LED turns on and Auto Manual Pass indicates orange. Monitor Level 30 SEC Reset Mic 1 Mic 2 Mic 3... -
Page 11: Pre-Mixer Volume Control
8. Pre-mixer volume control Microphone Mic 1 has priority for broadcasting WMP-2100 Re-Start Mic 2 ~ Mic 4 adjust Mic2~Mic4 Voice Level Mic 1 Mic 2 Mic 3 Mic 4 Auto Manual Pass Aux 1 adjust volume of Monitor Level... -
Page 12: Multi-Function Operating
9. Multi-function operating Video WMP-2100 Button to enable Re-Start multi-function Voice Level Eight multi-function Clear Auto Manual Pass control buttons Monitor Level 30 SEC Reset Mic 1 Mic 2 Mic 3 Mic 4 Group Aux 1 Aux 2 Aux 3... -
Page 13: Identification And Solution For Remote Call Back
Video 10. Identification and Solution for Remote Call back 1. When remote call back button is pressed WMP-2100 Re-Start When 30 SEC is activated, call Voice Level back signal will stop in 30 seconds Auto Manual Pass Monitor Level 30 SEC... -
Page 14: Security Alarm
Video 11. Security Alarm 1. When security alarm is triggered WMP-2100 Re-Start Voice Level Auto Manual Pass Monitor Level The LED of the zone will 30 SEC Reset be flashing red and you Mic 1 Mic 2 Mic 3 Mic 4... -
Page 15: Scan Remote Status
12. Scan remote status Video WMP-2100 Auto and Manual scan Re-Start Voice Level Scan manually Auto Manual Pass Monitor Level Reset 30 SEC Scan automatically Mic 1 Mic 2 Mic 3 Mic 4 Aux 1 Aux 2 Aux 3... -
Page 16: Emergent Broadcasting Backup System
Video 13. Emergent Broadcasting backup system WMP-2100 Re-Start Press Pass (LED will turn on) to Voice Level broadcast to all areas when main control unit malfunctions due to Pass Auto Manual Pass unknown reasons Monitor Level 30 SEC Reset Mic 1... -
Page 17: Telephone Broadcasting
1. Select available line from the PSTN (public switched telephone network)/ Dial designated line code on the phone. As pressing the key which represents telephone broadcasting, WMP-2100 will be turned on. 2. Press the numbers of desired zones or group. It’s available from single zone, group, or all call. -
Page 18: Group Broadcasting Table
Video 16. Group broadcasting table Press 999 All 192 zones are on〈ALL CALL〉 Video Press 000 Clear all the areas on the control units Press (＊)Cancel the incomplete number but not limited to correct combination you have entered. Groups broadcasting table： Groups Enable groups Disable groups...
Need help?
Do you have a question about the WMP-2100 and is the answer not in the manual?
Questions and answers