Download
Share
Print this page
  1. Manuals
  2. Brands
  3. RA Manuals
  4. Indoor Furnishing
  5. R-Style Flip
  6. Assembly instructions manual

RA R-Style Flip Assembly Instructions Manual

Hide thumbs
1
2
3
4
5
6
7
8
9

Advertisement

Quick Links

Download this manual
R-Style Flip Table Assembly Instructions
Failure to comply with or observe all assembly, safety, and operation instructions
and warnings regarding the use of this product may result in serious property dam-
age or bodily injury.
Make sure no obstacles are in the desk's path and all cords are of appropriate length for the
desk. Always maintain a 1" clearance around the table to prevent pinching.
Never assemble (or disassemble) the table or components with the table plugged into a pow-
er outlet. This product is for use on a nominal 120-volt circuit and has a grounding plug. Make
sure that the product is connected to an outlet having the same configuration as the plug. No
adapter should be used with this product.
Warranty: raproducts.com/warranty
Instruction #54061 • Dated: 04/17/2018
1 of 9

Advertisement

loading

Summary of Contents for RA R-Style Flip

  • Page 1 R-Style Flip Table Assembly Instructions Warranty: raproducts.com/warranty Failure to comply with or observe all assembly, safety, and operation instructions and warnings regarding the use of this product may result in serious property dam- age or bodily injury. Make sure no obstacles are in the desk’s path and all cords are of appropriate length for the desk.

  • Page 2: Tools Required For Assembly

    Tools Required for Assembly R-Style Flip Table #54061 A. Power Driver with Adjustable Torque B. Tape Measure C. #2 Phillips Head Driver Bit D. #2 Square Head Drive Bit (Recommended) Hardware and Tools Included for Assembly (may have extra) E. 8mm x .625 Machine Screw x8 8mm x .75 Thread Screw x8...
  • Page 3 Step 1 R-Style Flip Table #54061 • Screw all four leveling nuts onto the caster stems using the caster wrench. Step 2 • Screw the casters onto both leg assemblies. K&A Manufacturing • 800.298.4351 • www.raproducts.com/install 3 of 9...
  • Page 4 Step 3 R-Style Flip Table #54061 • Lay the beam on a protective surface with the insert channels facing up. • Place one of the leg assemblies over the main beams sliding the insert into the hollow leg assembly. The leg assemblies are interchangeable.
  • Page 5 Step 5 R-Style Flip Table #54061 Pull Up on Pin • Set the hinge mechanisms on the main beam. • Open up both mechanism assemblies by pulling out the pins. • Place the retainer into the slots on the body of the mechanisms. This is to lock Pull Up on them from closing.
  • Page 6 Step 7 R-Style Flip Table #54061 • Place the pull bar on the mechanisms ends rotating them so the set screw holes face the bottom side of the worksurface. • Thread the set screws on with the allen wrench. Step 8 •...
  • Page 7 Step 9 R-Style Flip Table #54061 • Place the worksurface on a protected surface with the pilot holes facing up. • Unlock the retainers on the base and close the mechanism assemblies by pulling out on the connector tube, and rotating the assemblies until they lock into place.
  • Page 8 Step 11 R-Style Flip Table #54061 • Place the assembled base on its caster wheels. • Pull out on the pull bar and flip the table in the vertical position. • Place the retainers into the slots to lock it into place.

  • Page 9: Operation

    Step 13 R-Style Flip Table #54061 • Place a spacer between the latch on each mechanism and the underside of the worksurface. Place the spacer tight to the forward end of the slot. • Attach with wood screws. Tighten so the latch can still slide in and out.