Subscribe to Our Youtube Channel
Summary of Contents for Diamatic BS-110 MKIII
- Page 1 OPERATING MANUAL BS-110 MKIII VERSION 1.1 FOR MORE INFORMATION VISIT WWW.DIAMATICUSA.COM Diamatic 05/2013 ● This document is not contractual ● Design and technical specifications may be subject to changes...
-
Page 2: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY in accordance with Appendix II sub A of Directive 2006/42/EC DIAMATIC USA 5220 Gaines Street San Diego, CA 92110 Tel: 866.295.5512 Fax: 619.295.0754 info@diamaticusa.com Declare under our sole responsibility that the machine as described below conforms with the Health and Safety requirements of the European Directive of the machine Safety. -
Page 3: Table Of Contents
Table of contents EC Declaration of Conformity 1 Introduction 2 Machine description 3 Safety Safety precautions Safety regulations Safety instructions 4 Initial operation Checkpoints of electrical safety Checkpoints of machine safety Drive wheel engaging and disengaging Transport wheel 5 Operation Electric controls Height adjusting steering handle Narrow mode steering handle... -
Page 4: Introduction
Only authorized and trained personnel may operate this machine. 2. Machine description The Diamatic BS-110 stripper is ideally suited for small and medium sized applications. The machine have a strong electric drive system with a very easy operating with forward, backward and speed control function. - Page 5 M12 nuts, unscrew for remove weights Drive switch lever for narrow mode Transport wheel 10 Lifting eye Selection switch 11 Drive wheel with quick release pin Speed control 12 Hole for pin for handle in transport position Clamp lever adjustable steer handle Shock absorbing handle...
-
Page 6: Safety
Safety instructions Pull out the main plug during inspections and repairing on the machine. ▪ Keep the machine original, only use original Diamatic parts. ▪ Do not pull out the power supply cable by the wire, but by the connector. -
Page 7: Initial Operation
The weight of the BS-110 MKIII is 170kg with the weights. Use preferably appropriate appliances as a ▪ lift or crane. Use the existing lifting points to lift the machine. Never lift the machine with mounted tool! This sharp tool can be very dangerous! ▪... -
Page 8: Transport Wheel
Transport wheel The transport wheel helps to move the machine easily and eliminate damaging to the floor. Loosen the 2 rubber clamps and rotate the handle forwards. Secure the handle by inserting 2 quick release pins. 5. Operation Electric controls The selection switch (1) is mount on top of machine. -
Page 9: Height Adjusting Steering Handle
Height adjustment steering handle Adjusting the height of the steering handle is possible by loosening the clamp levers (1) to find a comfortable working position. Narrow mode steering handle To work as close as possible along the wall it is possible to remove the right handle grip. The handle grip (2) can be screw into the opposite side of the handle. -
Page 10: Blade Choice
Blade choice Proper blade size and placement, depending on material and sub-floor type, affects performance. - The harder a job comes up, for best results, use a smaller blade. - Start with a narrow blade, then increase the blade size to optimize the cutting pass. - Narrower blades work easier than wider blades. -
Page 11: Blade Changing
Blade changing Dull blades greatly reduce cutting ability. Re-sharpen or replace as needed. Always wear gloves when changing blades. Use extended wrench to keep hand safely away from the edge of the blade. Place a bock (1) under the front of the machine and loose the five hex head bolts and replace the blade. It is not necessary to remove the bolts. -
Page 12: Types Of Tear Outs
Types of tear outs Keep blades sharp! Keep your work area clean and clear of debris. Always wear eye- and ear- protection when working with the machine. VCT - Tile Never use a blade wider than the size of the tile being removed. If goods being removed still do not come up clean or the machine jumps on top of goods, reduce blade size to a smaller blade until proper blade size is found or use a smaller portion of the blade. -
Page 13: Remove Weights
True parkay flooring scoring is not necessary. It will come up in small pieces. When working over plywood sub-flooring, try to run machine in the same direction as the grain in the wood. Blade in most cases bevel down. On solid wood floors like plank, run in the same direction as the plank, not cross grain or cross plank. -
Page 14: Maintenance
6. Maintenance Wheel scraper plates Keep wheels clean from dirt/debris. To adjust the scraper plates unplug electrical supply cable and loosen the bolts. Slide up to face wheel until it touches but does not dig into the wheel surface. Over tightening scraper plates could cause damage to wheel. Replace shock absorbers To replace the shock absorbers first remove the weights as described on previous page. -
Page 15: Technical Data
899 mm Length (L) 522 mm Width (W) 1062 mm Height (H) Minimum height steering 888 mm handle (H1) Maximum height steering 1081 mm handle (H2) 170 kg Weight Design and specifications are subject to change without notice by Diamatic USA... -
Page 16: Contact
DIAMATIC USA DIAMATIC MEXICO DIAMATIC CANADA 5220 Gaines Street San Diego, CA 92110 Tel: 866.295.5512 Fax: 619.295.0754 info@diamaticusa.com...
Need help?
Do you have a question about the BS-110 MKIII and is the answer not in the manual?
Questions and answers