1. Manuals
  2. Brands
  3. Dare Manuals
  4. Modem
  5. DB101
  6. User manual

Dare DB101 User Manual

Usb adsl modem
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DB101
USB ADSL MODEM
USER'S MANUAL
V3.0
DARE TECHNOLOGIES CO., LTD.
http://www.dare-tech.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DB101 and is the answer not in the manual?

Questions and answers

Summary of Contents for Dare DB101

  • Page 1 DB101 USB ADSL MODEM USER’S MANUAL V3.0 DARE TECHNOLOGIES CO., LTD. http://www.dare-tech.com...

  • Page 2: Table Of Contents

    DB101 ADSL MODEM Manual CONTENTS 1. OVERVIEW............................... 2 1.1 ABOUT ADSL .............................. 2 1.2 DEVICE INTRODUCTION.......................... 2 1.3 PROTOCOL AND DRIVER.......................... 2 1.4 CHARACTERISTICS ........................... 3 2. USB ADSL MODEM INSTALLATION AND SOFTWARE CONFIGURATION ........4 2.1 SYSTEM REQUIREMENTS........................4 2.1.1 HARDWARE ............................

  • Page 3: Overview

    DB101 ADSL MODEM Manual 1. OVERVIEW 1.1 ABOUT ADSL An ADSL MODEM is a broadband access device, which utilizes the high frequency segment of a phone line to transmit high-speed data without interfering with the voice transmission. The frequency of the ADSL signal is higher than that of voice, so the voice and ADSL signal can coexist in one line by using a Splitter to insulate the two.

  • Page 4: Characteristics

    DB101 ADSL MODEM Manual Bridged IP over ATM LLCSNAP (RFC1483) Routed IP over ATM LLCSNAP (RFC1483) Bridged IP over ATM VCMUX (RFC1483) Routed IP over ATM VCMUX (RFC1483) Classical IP over ATM (RFC1577) Driver Types and OS Supported Table 1...

  • Page 5: Usb Adsl Modem Installation And Software Configuration

    DB101 ADSL MODEM Manual 2. USB ADSL MODEM INSTALLATION AND SOFTWARE CONFIGURATION 2.1 SYSTEM REQUIREMENTS 2.1.1 HARDWARE • Pentium® MMX 233(or higher) • Minimum of 32MB memory. • Minimum 10MB free disk space. • CD-ROM • USB port 2.1.2 SOFTWARE •...

  • Page 6: Driver Installation

    DB101 ADSL MODEM Manual Plug the other end of the USB cable as shown here to the ADSL USB port as shown by interface in Figure 1 Section 1. After you complete the above steps, your PC will indicate, “Found new hardware and installing driver”.
  • Page 7 DB101 ADSL MODEM Manual A new dialog box will ask which searching method should be chosen. Select default method and click “Next” button. As shown figure 2.3.1.2. 2.3.1.2 Figure A new box will pop up for selection of the location of the driver. If the location is incorrect please click “Browse”...
  • Page 8 DB101 ADSL MODEM Manual 5. A message box will show the installation is complete. Click “Finish” button. As shown figure 2.3.1.5. 2.3.1.5 Figure A new icon will be appear in the taskbar on the lower right corner of the screen.
  • Page 9 DB101 ADSL MODEM Manual 2. A message box will indicate the installation is finished. Click “Finish”. Figure 2.3.2.2 “Digital signature not found” dialog box will appear again, click “Yes” to continue. Figure 2.3.2.3 4. A new icon will appear in the taskbar at the lower right corner of the screen.

  • Page 10: Customer Configuration

    DB101 ADSL MODEM Manual 3. CUSTOMER CONFIGURATION 1. Double click “USB ADSL” icon in the Control Panel. As shown figure 3.1 Figure 3.1 Figures 3.2 Or double click “ADSL CONTROL PANEL” icon on the desktop. As shown figure 3.2 2. A dialog box will appear as shown below. As shown figure 3.3 Figure 3.3...
  • Page 11 DB101 ADSL MODEM Manual 3. Press ALT+C and a control box will appear. The default parameters as shown below: • The value of VPI and VCI are set to the value of VPI=0 & VCI=32. • The Encapsulation mode is the default value “PPP over Ethernet LLCSNAP (RFC2516)”.

  • Page 12: Uninstallation

    DB101 ADSL MODEM Manual 4. UNINSTALLATION METHOD 1: Click “Start” “Settings” “Control Panel”.Then double click “Add/Remove Program” icon in the Control Panel window. Figure 4.1 Figure 4.2 2. Select “USB ADSL Adapter” in the display dialog box and then click “Add/Remove” button. As shown figure 4.2...
  • Page 13 DB101 ADSL MODEM Manual 2. For either method it will ask you to click“Yes”to confirm deletion. As shown figure 4.4. Figure 4.4 3 Click “Yes” to restart the computer. As shown figure 4.5. Figure 4.5 - 12 -...

  • Page 14: Connection Setup

    DB101 ADSL MODEM Manual 5 CONNECTION SETUP There are different kinds of connection: Physical Layer Connection, PPP Dial-Up Connection and Private Connection. They will be introduced individually in this section. 5.1 PHYSICAL LAYER CONNECTION 1. The Physical Layer Connection will automatically run after the telephone line is connected. The taskbar shall be shown as below if the connection is good.

  • Page 15: Dial-Up Connection

    DB101 ADSL MODEM Manual Figure 5.1.3 Or click the “Start ADSL” button to reconnect ADSL. 4 You may now install PPP Dial-up connection after finishing the steps stated above for physical layer connection. 5.2 DIAL-UP CONNECTION Microsoft Windows® 98 v1.0 and v2.0 Before dialing, confirm the value of VPI, VCI and Encapsulation mode according to Chapter 3.
  • Page 16 DB101 ADSL MODEM Manual Figure 5.2.3 Items can be modified are listed in the dialog box Figure 5.2.4 Click the “OK” button to exit. Windows® 2000 The configuration process is similar to Win98. - 15 -...

  • Page 17: Private Line Connection

    DB101 ADSL MODEM Manual 5.3 Private Line Connection Microsoft Windows® 98 Install the LAN driver. Set values for VPI, VCI and Encapsulation mode. Figure 5.3.1 Double click the “Network” icon in “Control Panel”. Choose the “Configuration” page, select “TCP/IP USB ADSL Adapter” and click “Properties”. As shown in figure 5.3.2.
  • Page 18 DB101 ADSL MODEM Manual Figure 5.3.2 Figure 5.3.3 - 17 -...

  • Page 19: Pppoe Configuration

    DB101 ADSL MODEM Manual In the “TCP/IP Properties” dialog box select the “IP Address” page. Select the “Specify an IP address” radial box and input the correct IP address and subnet mask (you will need to contact your service provider to get the correct value of the IP address and subnet mask).

  • Page 20: Specification

    DB101 ADSL MODEM Manual 7. SPECIFICATION 7.1 POWER SUPPLY Uses USB bus for power. No power supply is needed. Power consumption ≤ 2.5W 7.2 DIMENSION 138mm Length x 104mm Width x 13mm Height 7.3 WEIGHT 300g 7.4 CERTIFICATIONS EMI/Immunity: FCC Part 15 Class B, CE Mark (EN55022 Class B/EN50082)

  • Page 21: Appendix A Glossary

    DB101 ADSL MODEM Manual APPENDIX A: GLOSSARY ATU-C ADSL Transceiver Unit, Central Office End ATU-R ADSL Transceiver Unit, Remote Terminal End FEXT Far-end Cross Talk HDSL High-rate Digital Subscriber Line POTS Plain Old Telephone Service PSTN Public Switched Telephone Network...
  • Page 22 DB101 ADSL MODEM Manual Point to Point protocol Domain Name Server Virtual Path ID Virtual Circuit ID Digital Subscriber Line Internet Protocol Central Office Echo Canceling - 21 -...

  • Page 23: Appendix B Troubleshooting

    DB101 ADSL MODEM Manual APPENDIX B: Troubleshooting Phenomena Suggested Solution Power supply light is off. Make sure the USB connection is tight. • Check to see if the modulate and demodulate modes have Power supply light is on, but been correctly selected Link light is blinking.

  • Page 24: Appendix C Splitter Connection

    DB101 ADSL MODEM Manual APPENDIX C: SPLITTER CONNECTION Splitter • Use a telephone cord to connect the LINE port of the splitter with the telephone RJ-11 port on the wall. • Use another telephone cord to connect the ADSL port on the Splitter with the Line port on the ADSL Modem.

  • Page 25: Appendix D Shipping List

    DB101 ADSL MODEM Manual APPENDIX D: SHIPPING LIST - 24 -...
  • Page 26 DB101 ADSL MODEM Manual DARE TECHNOLOGIES CO., LTD. Add: 12250 El Camino Real, #350 San Diego, CA 92130 China Company: 22F, Shanghai Information Building, NO. 1555, Kongjiang Road, Shanghai, China, 200092 Tel: (858) 755 8822 Fax: (858) 755 8896 www.dareglobal.com www.dare-tech.com...

Table of Contents