Yeacomm YF-P11K User Manual

LTE Wireless Terminal (Set) YF-P11K User manual
Thanks for choosing Yeacomm 4G wireless router, please read and keep the user's manual carefully. It is more convenient for you to use our router.
We reserve the right to amend the technical parameters of the user's manual. We will improve the user's manual and adjust the printing errors in time without notification
in advance. All rights are reserved.
1. Main Technology Parameters
Working temps : -30℃ -- +60℃

Relative humidity : 5%--95%

Working frequency : FDD: B1/B2/B3/B5/B7/B8/B12/B17/B20, B4/B28 (Optional)

TDD Band 38/39/40/41, B42/B43(optional)
WCDMA: 900/2100Mhz, 850/900/1900/2100Mhz(Optional)
GSM: 850/900/1800/1900Mhz
Frequency can be customized according to your requirements
Power supply : input AC :100V~240V，50Hz~60Hz·

Output DC: 15V, 1000mA
Rate of uplink and downlink： LTE(Category 4): DL 150Mb/s；UL 50Mb/s

2. Installation
2.1. Picture shows below. When you hear a "click" sound, it means that the USIM card has been installed successfully.
2.2. Use Cate5e cable to connect the indoor router's WAN/POE port and outdoor router LAN port.
2.3. Placed the set outside at open space, the front direction toward the base station and fix well.
2.4. Use Adapter to connect External power outlet and the indoor unit. The system will automatically power on after connected, about 1~2 minutes.
Attention:
1) Please do not insert USIM card when connecting with the external power supply
2) Please do not contact with the mental surface when removing the USIM card, it will damage the card.
3) Please use the original standard power adapter.
3. About Terminal
The terminal can work under the LTE network, only supports data and SMS service, does not support voice business.
3.1. Equipment connection diagram.
NOTE: Outdoor unit is powered by indoor unit. Pls connect the WAN/POE port of indoor unit to the outdoor unit, as follows:
3.1.1. Indoor interface introduction
Port type Port function
POWER Power connector, use the original Please the Use original standard power adapter, if not may
power adapter, power connector damage the products or other danger.
input voltage range of 6 ~ 15V,
current must more than 1A.
RESET Restart the terminal default Restore factory setting will clear all the user's parameters,
configuration. if necessary, please reset.
LAN1~LAN2 Ethernet port, connect computer Indoor router do not need SIM card.
remarks
or other devices.
WAN/POE Ethernet uplink interface / POE Attention：WAN port can not connect other device.
power supply interface for
connecting the outdoor unit.
3.1.2. Outdoor router introduction
Port type Port function
SIM Install USIM card interface, please Please do not insert or take out the SIM card when the power
follow the instructions install USIM on .
card, stick the waterproof stickers
after installed card
LAN Ethernet port， Use to connect Indoor and outdoor router should use Cate5 connect , and
indoor router WAN/POE port the distance should within 50 meters.
3.2. Indicator
3.2.1. indoor unit indicator
Indicator type status Description (from left to right )
Off Power abnormal, the router power off
POWER
On Power normal, the router power on
Off no signal (the signal status can be checked by terminal configuration
page)
SIGNAL Red The signal is poor
Yellow Signal is moderate
Green Signal is good
Off WiFi off
WLAN
flicker WiFi on and has data transmission
Off Outdoor unit do not connect with indoor unit .
DATA
On Outdoor unit connects with indoor unit .
Off Outdoor unit do not connect with indoor unit .
WAN
Light Outdoor unit connects with indoor unit .
Off Do not connect with PC
LAN1/LAN2
Light Connect with PC correctly
3.2.2. outdoor indicator
Indicator Status Description
RF All off no signal (the signal status can be checked
by terminal configuration page)
One on The signal is poor
Two on Signal is moderate
Three on Signal is good
All on Signal is very good
SYS Off Power abnormal, the router power off
On Power normal, the router power on
SIM Off No SIM or Can not read SIM
On Terminal read the SIM normally
ETH Off Terminal doesn't link with PC
On Terminal have link with PC
RUN Off Terminal is doesn't running
On Terminal is running
4. Access internet
The indoor router support standard internet cable or WLAN wireless way to connect computer, do not need any driver; Support Windows XP, Windows 7,Windows 8,MAC
OS, Linux, Android and so on;
Please confirm the sets has been installed well ad the manual before access the internet .
4.1. Access PC
The indoor router support standard internet cable or WLAN wireless way to connect computer, the router's SSID and WIFI password information is at the bottom of the
sticker. Each router's SSID and WIFI password is unique. No matter what way to connect, please make sure to set the mode: obtain IP address as automatically.
remarks