Advertisement
Introduction
Thanks for choosing the Vision's In-Wall Switch module of the home automation device.
This module is a Z-Wave™ enabled device (interoperable, two-way RF mesh networking
technology) and is fully compatible with any Z-Wave™ enabled network. Every mains
powered Z-Wave enabled device acts as a signal repeater and multiple devices result in
more possible transmission routes which helps eliminate "RF dead-sports".
Z-Wave™ enabled devices displaying the Z-Wave™ logo can also be used with it
regardless of the manufacturer, and ours can also be used in other manufacturer's
Z-Wave™ enabled networks. With special design, this module can fit into most of
electronic box in the market. This module will send On/Off signal to the appliance that
attached to this module by receiving Z-Wave™ signal from controller. It also can control
two appliances independently.
Product Description and Specification
Specification:
Protocol: Z-Wave™ (ZM3102N)
Frequency Range:
865.22MHz (ZL7432IN)
868.42MHz (ZL7432EU)
869.00MHz (ZL7432RU)
908.42MHz (ZL7432US)
916.00MHz (ZL7432IS)
920.00MHz (ZL7432JP)
921.42MHz (ZL7432BR)
Operating Range: Up to 100 feet line of sight
Operating Temp.: -15°C~ 60°C (5°F~140°F)
Operating Voltage: 100VAC~240VAC
Resistive Load:
550W for 110VAC
1100W for 220VAC
Z-Wave™ Command Class
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_MULTI_CHANNEL_V3
COMMAND_CLASS_SWITCH_ALL
COMMAND_CLASS_SWITCH_BINEARY mapping COMMAND_CLASS_BASIC
COMMAND_CLASS_VERSION
Installation
Notice: If you are installing the entire Z-Wave™ system for the first time, please refer to
the installation guide of Z-Wave™ Interface Controller before installing ZL7432 In-Wall
Switch Module.
1.
Following the wiring diagram to install ZL7432 according to your varied
requirements.
Package Content
1pc ZL 7432 In-Wall Switch,
2 Relays
1pc Installation & Operation
Manual
-1-
Note: Place antenna toward the surface and away from metal to get better signal.
For "Inclusion" in (adding to) a network: Put the Z-Wave™ Interface Controller
2.
into "inclusion" mode, and following its instruction to add the ZL 7432 to your
controller. To get in the "inclusion" mode, the distance between module and
controller is suggested to be in one meter. Turn on and turn off the wall switch that
connects with ZL 7432 module 4 times to be included. (or press the Program SW 4
times within 2 seconds to be included)
For "Exclusion" from (removing from) a network: Put the Z-Wave™ Interface
Controller into "exclusion" mode, and following its instruction to delete the ZL 7432
from your controller. Turn on and turn off the wall switch that connects with ZL
7432 module 4 times to be excluded. (or press the Program SW 4 times within 2
seconds to be excluded)
For Wall SW1, ZL 7432 will report the status of On/OFF after doing "Association".
3.
However, Wall SW2 will only report the status if Z-Wave™ Interface Controller
support Multi Channel command, and send Get Command to ask ZL 7432 Wall SW
2 to report the status.
4.
User can use the following command class to control relay 1 and/or 2 in order to
control the appliances that attached to ZL7432
For relay 1:
Status of "ON" (Binary Switch Set 0xFF or wall switch ON)
Status of "OFF" (Binary Switch Set 0x00 or wall switch OFF)
For relay 1 or 2: Please use Multi-Channel command class to control
5.
Reset to the factory default setting: Press and hold the Program SW before power
on.
-2-
Advertisement
