1. Manuals
  2. Brands
  3. lighting control & design Manuals
  4. Control Systems
  5. GR 2400
  6. Programming manual

lighting control & design GR 2400 Programming Manual

Relay panel
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
GR 2400
BASIC PROGRAMMING GUIDE
Programming Guide Index
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Navigation Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Programming a Digital Switch . . . . . . . . . . . . . . . . . 4
Adding or Deleting Loads . . . . . . . . . . . . . . . . . . . . . . 5
Basic Photocell Settings . . . . . . . . . . . . . . . . . . . . . . 6-7
Editing Time Schedules . . . . . . . . . . . . . . . . . . . . . . . . 8
Schedule Types & Trigger Events . . . . . . . . . . . . . . . 9
Programming Groups . . . . . . . . . . . . . . . . . . . . . . . . . 11
Important Note:
This programming guide covers the basics-programming switches, schedules and photosensors . Other manuals
exist for more advanced programming issues . Call us if you have questions or need assistance during the
programming of your system . Technical Support: 800-345-4448

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GR 2400 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for lighting control & design GR 2400

  • Page 1: Table Of Contents

    GR 2400 BASIC PROGRAMMING GUIDE Programming Guide Index Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Navigation Basics .

  • Page 2: Introduction

    INTRODUCTION Introduction: Almost all of the devices in the GR The DTC (Digital Time Clock): Most 2400 Lighting Control System are digital, meaning programming is done from the DTC Clock (shown they are part of a peer-to-peer network and can below)/Programmer located in the master be programmed .

  • Page 3: Navigation Basics

    NAVIGATION BASICS Menu: “Select a Switch” SWITCHES PAGE 1-2 #33: Reception Tabbing: Use the TAB #52: Master Sw 1 buttons to move around the #53: Master Sw 2 display: #59: Master Sw 3 #61: Hallway 100 #61: Hallway 200 #61: Hallway 220 DOWN to position the cursor .

  • Page 4: Programming A Digital Switch

    PROGRAMMING A DIGITAL SWITCH To Start: USER MENU 1. TAB to start. MANUAL OVERRIDE 2. TAB to Program Switch. REVIEW SCHEDULE 3. ENTER to select. GROUP LOADS PROGRAM SWITCH PROGRAM SWITCH SETUP MENU This indicates page 1 of 2: For Multiple Pages: SWITCHES PAGE 1-2 PAGE 1-2...

  • Page 5: Adding Or Deleting Loads

    ADDING OR DELETING LOADS Adding or deleting loads from a switch, SWI ID63-1 MAINTAIN MAINTAIN photocell, time schedule or group is always EDIT: LCP-1 LOAD-1 done in the same way . Once you have Indicates Control Type* navigated to the correct Button, Trigger or Group and before you add or delete loads, it is (Refer to page 10 important to determine the Control Type .*...

  • Page 6: Basic Photocell Settings

    BASIC PHOTOCELL SETTINGS To Start: USER MENU 1 . TAB to start . MANUAL OVERRIDE 2 . TAB to Program Switch . REVIEW SCHEDULE 3 . ENTER to select . GROUP LOADS PROGRAM SWITCH PROGRAM SWITCH SETUP MENU For Multiple Pages: (more than 7 switches) SWITCHES PAGE 1-2 PAGE 1-2...
  • Page 7 BASIC PHOTOCELL SETTINGS (cont’d) To Program a Trigger Level: SENSOR ID#64-1 “Analog” followed Photocell Cards come with one or three by an integer (1, Analog 1: Analog 1: 0050 photocell inputs . Any of those photocells may 2, 3) indicates this Time Delay: TEST 5 Sec be used to control the Trigger .

  • Page 8: Editing Time Schedules

    EDITING TIME SCHEDULES To Start: USER MENU 1 . TAB to start . MANUAL OVERRIDE 2 . TAB to REVIEW SCHEDULE . REVIEW SCHEDULE REVIEW SCHEDULE 3 . ENTER to select . GROUP LOADS PROGRAM SWITCH SETUP MENU This indicates page 1 of 6 .

  • Page 9: Schedule Types & Trigger Events

    SCHEDULE TYPES & TRIGGER EVENTS 1 . SCROLL to the desired schedule type . SCH 1 EXCEPT NONE EVERY DAY EVERY DAY Every Day (7-day schedule): Schedule Type: TIME: 09:00 AM 1 . TAB to ON TIME and SCROLL to select Trigger •...

  • Page 10: Control Types & Group Types

    CONTROL TYPES & GROUP TYPES Control Types: ”Control Types” describes how loads are controlled . TOGGLE Toggle up to 8 loads On or Off . ON MODE Up to 8 loads On only . OFF MODE Up to 8 loads Off only . Also known as an “interlock”—this turns one set of loads On and MIXED MODE another set of loads Off .

  • Page 11: Programming Groups

    PROGRAMMING GROUPS To Access the Group: USER MENU Within the DTC, there are two paths you can use MANUAL OVERRIDE to access a group for programming purposes: REVIEW SCHEDULE A) From USER MENU: GROUP LOADS GROUP LOADS PROGRAM SWITCH 1 . TAB to start . 2 .
  • Page 12 Lighting Control & Design 9144 Deering Ave ., Chatsworth, CA 91311 www .lightingcontrols .com © 2007, 2009, 2010 Acuity Brands Lighting Inc., All Rights Reserved. • Form No. 1382.017 994-004-0022...

Table of Contents