Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Inflight Fitness Manuals
  4. Elliptical Trainer
  5. CT-CCO
  6. Manual

Inflight Fitness CT-CCO Manual

Cable cross
Hide thumbs

Advertisement

Quick Links

Download this manual
CT-CCO CABLE CROSS

Advertisement

loading

Summary of Contents for Inflight Fitness CT-CCO

  • Page 1 CT-CCO CABLE CROSS...
  • Page 3 CCO ASSEMBLY INSTRUCTIONS IMPORTANT NOTICES Read all warning labels, the instruction placard and this manual before attempting to use this machine. Always consult your physician and an exercise professional before beginning any exercise program/regimen. Before any test or use check for proper assembly of the machine including (but not limited to): bolts and other hardware fastened properly, cables in pulley grooves and routed correctly.
  • Page 4 CCO PARTS AND HARDWARE HARDWARE DESCRIPTION QUANTITY Bolts 3/8” x 8 ½” 3/8” x 5” 3/8” x 4 ¾” 3/8” x 4 ¼” 3/8” x 4” 3/8” x 2 ¾” 3/8” x 2 ½” 3/8” x 2 ¼” 3/8” x 2” 3/8”...
  • Page 5 CCO PARTS AND HARDWARE PARTS WHITE / PLATINUM FRAME PARTS Loop Upright (2) Bottom Bracket (2) Base Tube (2) BLACK FRAME PARTS Top Beam (2) Pulley Carriage (2) Upper Pulley Bracket (2) Handle (4) Round Cable Retainers (4) Stabilizer (2) Center Tube Connector Tubes (2) CABLES AND PULLEYS...

  • Page 6: Bottom

    CCO ASSEMBLY INSTRUCTIONS PRE - ASSEMBLY ONLY A. Assemble the two Connector Tubes to the Center Tube with 4 – 3/8” x 2 ¼” bolts, 8 –3/8” flat washers, and 4 – nuts. Do not fully tighten at this time. B.
  • Page 7 1 - Center Tube 2 - Connector Tubes 4 - 2 1/4" Bolts 8 - Flat Washers 4 - Nuts 4 - Rubber Stops 2 - 2 3/4" Bolts 4 - Flat Washers 1 - Chin-up Bar 2 - Nuts 2 - 4"...

  • Page 8: Loop

    CCO ASSEMBLY INSTRUCTIONS MAIN STRUCTURE ASSEMBLY BUILD TWO OF THE ASSEMBLIES DETAILED IN STEPS F- I F. Attach the Rear Stabilizer and Base Ass’y (from Step D.) to the Loop Upright using 4 – 3/8” x 8 ½” bolts, 8 – 3/8” flat washers and 4 - 3/8” nuts. G.
  • Page 9 H (x 2) 1 - Top Beam 2 - 4 3/4" Bolts I (x 2) 2 - 2 3/4" Bolts 4 - Curved Washers 1 - 2 1/2" Bolt 2 - Washers 1 - 4 1/4" Bolt 2 - Nuts 2 - Washers REMOVE BLACK END CAP F (x 2)

  • Page 10: Upper Pulley

    CCO ASSEMBLY INSTRUCTIONS WEIGHT STACK ASSEMBLY AND FRAME COMPLETION J. Now install the weights only to the assembly that was placed in its final position. The weights will be installed to the other assembly at Step M. Insert Guide Rods into the base of the Loop Upright. Allow Guide Rods to lean back towards stabilizer.
  • Page 11 Notes for Step L: Support the Center Beam and never pull down. 1 - 2 1/2" Bolt (remove and re-install) Slightly lift the Frame Ass'y as 2 - Washers you slide it onto the Center Beam. 1 - Nut This is a two person task. Detail of Upper Pulley Bracket...

  • Page 12: Round Cable

    CCO ASSEMBLY INSTRUCTIONS CABLE AND PULLEY INSTALLATION O. Uncoil the cables that are pre-assembled to the top weight. At the rear of the top weight is the middle of the cable. Make sure the cable is sitting in the grooves of the two pulleys in the top weight bracket. Lift the middle of the cable up to the Upper Pulley Bracket at the top of the Guide Rods.
  • Page 13 S (x 2) T (x 2) O (x 2) 1 - Pulley 1 - Pulley 1 - 1 3/4" Bolt 1 - Pulley 1 - Cable Retainer 1 - 1 3/4" Bolt 2 - Washers 1 - Spacer 1 - Washer 1 - Nut 1 - 4 1/4"...
  • Page 14 CCO ASSEMBLY INSTRUCTIONS BALLET HANDLES V. Attach two ballet handles to each Loop Upright using 8 – 4 ¾” bolts, 16 – washers, 8 – nuts. SHROUD HOLES AND SHROUD OPTION W. If no Optional Shroud Kit was purchased install plastic caps in all 24 shroud holes.
  • Page 15 Cable View: Step O Cable View: Steps P, Q, R Cable View: Steps S, T, U Handle and Optional Shroud Installation...