Advertisement
Advertisement
Table of Contents
Related Manuals for Remo+ Remobell S
Summary of Contents for Remo+ Remobell S
-
Page 1: Quick Start Guide
Quick Start Guide www.remoplus.co... -
Page 4: What's In The Box
WHAT’S IN THE BOX REMOBELL® S WALL 15° ANGLE 5° WEDGE MOUNT MOUNT MOUNT MOUNT FOAM POWER KIT EXTENSION SCREWDRIVER MOUNTING WITH WIRE HARNESS WIRES SCREWS AND ANCHORS SAFETY FUSE WIRE NUTS BUBBLE POWER TERMINAL SCREWS DOORBELL SCREWS LEVEL SECURITY SCREWS DRILL BIT * For brick or stucco surfaces, you’ll need a drill. - Page 5 MEET REMOBELL® S FACEPLATE BODY* BACK LED Indicator Camera lens Power terminal Bell button IR LED Speaker Security screw holes Reset button Mounting holes * Remove the protective lm before use...
-
Page 6: Before You Begin
BEFORE YOU BEGIN Check your doorbell voltage and chime. RemoBell® S only works with a voltage of 16-24VAC. Go to your breaker box and turn o the power to your doorbell. WARNING: If you are not sure how to turn o the power to your doorbell from your breaker box, please consult a licensed electrician. - Page 7 POWER KIT INSTALLATION 1. Insert one end of the Wire 2. Remove the cover of your Harness into the Power Kit. mechanical chime. 3. Take a picture of the wiring for 4. Loosen the screws and remove the reference during installation. wires.
- Page 8 5. Connect the Wire Harness to the "TRANS" and "FRONT" chime terminals. 6. Insert an exposed end of the Wire Harness and one chime wire into the Wire Nut, and twist it tightly. Repeat with remaining wires. 7. Place your Power Kit so that it doesn't interfere with moving parts or mu e the chime.
- Page 9 DOORBELL MOUNTING 1. Remove your existing doorbell and disconnect the wires. 2. Based on your doorbell location, select the appropriate Mount (Optional) For hard surfaces like brick type to optimize the camera's or stucco, paste the Mount Foam to viewing angle. the back of your Mount.
- Page 10 4. Drill holes according to your 5. Secure the Mount onto the wall drill points and insert Anchors. using Screwdriver and Mounting Screws. 6. If a Power Kit is installed, follow Option A. If you do not have chime, follow Option B. Option A: Connect the RemoBell®...
- Page 11 Option B: Connect the Safety Fuse Wire with your existing doorbell wires. Insert an exposed end of the Safety Fuse Wire and one chime wire into the Wire Nut, and twist it tightly. Repeat with remaining wires. Push the Safety Fuse Wire and the Extension Wire into the wall to secure the Doorbell to the mount.
- Page 12 7. Remove the Faceplate. Fixate 8. Restore power on the breaker the RemoBell® S to the Mount box. If the LED Indicator ashes by inserting the Doorbell blue, then proceed to DoorBell Screws. Setup (Page 10). If not, turn o your power and check the doorbell wiring.
- Page 13 DOORBELL SETUP CREATE AN ACCOUNT 1. Make sure your mobile device is 2. Download and launch the connected to your home app. 2.4GHz Wi-Fi. (5GHz not supported) 3. Press SIGN UP at the bottom of 4. Enter your email and create a the login page.
- Page 14 REGISTER REMOBELL® S 1. Have your Wi-Fi network password available. 2. After logging into the app, press "+" on the home screen to add your device, and select your time zone. 3. Enter the password for the displayed Wi-Fi network and proceed to the QR code scan page.
- Page 15 8. Put the Faceplate back on and insert two Security Screws into the Security Screw Holes to secure the Faceplate. LED INDICATOR Doorbell is in AP Mode. Flashing Fast Flashing Slowly Doorbell is connecting to router. Blue Light Steady Doorbell is running. Flashing Doorbell is not connected.
- Page 16 Forgot your password? 1. Press “forgot password” on the login page. 2. Enter your account email and click SEND. 3. Check your email (including spam folder) for the temporary password. 4. Open the app and log in using your account email and the temporary password.
-
Page 17: Troubleshooting
TROUBLESHOOTING Can’t see the videos on your Recent Activity? For Android users, allow all permissions to the app: remo+ Settings > Applications Manager > Permissions > Storage Check your Settings: > Menu > Devices > Your Devices > Motion Sensor Turn on Motion Sensor >... - Page 18 Experiencing false motion alarms? Adjust the motion sensitivity of your RemoBell S: > Menu > Devices > Your Devices > Motion Sensitivity > Adjust settings De ne Motion Zones to cut out unwanted motion: (ex. Trees blowing in the wind, busy roadways) >...
-
Page 19: Electrical Shock Warning
ELECTRICAL SHOCK WARNING: DO TURN OFF POWER on the breaker box before RemoBell® S installation. Serious electrical shock, injury, or death may occur if left on. DO NOT TURN ON POWER until RemoBell® S installation is complete. Contact a licensed electrician if you need any assistance with power or wiring. SUPPORT We’re happy to help! support@remoplus.co... -
Page 20: Limited Warranty
LIMITED WARRANTY 1. LISCENSOR DOES NOT WARRANT THAT THE FUNCTIONS CONTAINED IN THE LICENSED PRODUCT AND HARDWARE WILL MEET LICENSEE’S REQUIREMENTS OR THAT THE OPERATION OF THE SOFTWARE AND HARDWARE WILL BE UNINTERRUPTED OR ERROR-FREE. LICENSOR DOES WARRANT THAT THE MEDIA ON WHICH THE SOFTWARE IS FURNISHED AND THE HARDWARE WILL BE FREE FROM DEFECTS IN MATERIAL AND WORKMANSHIP UNDER NORMAL USE FOR A PERIOD OF ONE YEAR FROM THE DATE OF DELIVERY (”WARRANTY... -
Page 21: Fcc Compliance Statement
FCC COMPLIANCE STATEMENT You are cautioned that changes or modi cations not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
Need help?
Do you have a question about the Remobell S and is the answer not in the manual?
Questions and answers
I installed a new RemoBell+ S to replace a quirky acting old one. I can't find how to delete the old one from the app.
To delete an old RemoBell S from the app, you need to remove the device from your account. This involves deleting the device in the app, resetting the doorbell, and then reinstalling and reconfiguring it.
This answer is automatically generated