Table of Contents
Advertisement
Quick Links
PSS-29ZBS Power Switch
Introduction
PSS-29ZBS is a ZigBee Power Switch. It is capable of receiving wireless signals from the coordinator in
the Zigbee network to toggle On/Off of appliances that are attached to it.
The Power Switch utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless
communication protocol that is reliable, has low power consumption and has high transmission
efficiency. Based on the IEEE802.15.4 standard, ZigBee allows a large amount of devices to be
included in a network and coordinated for data exchange and signal transmission.
The Power Switch serves as an end device in the ZigBee network. It can be included in the ZigBee
network to transmit or receive signal, but cannot permit any other ZigBee device to join the network
through the Power Switch.
Parts Identification
1. Function Button aka LED indicator
The Function Button also doubles as the LED Indicator. The
function button is used to control the Power Switch. The LED indicator
is used to indicate Power Switch status.
LED Indication:
The LED indicator lights up in the following conditions:
- On:
The Power Switch is turned on.
- Off:
The Power Switch is turned off.
- Flashes twice:
The Power Switch has successfully joined a ZigBee network.
- Flashes once every 20 minutes:
The Power Switch is not joined into any ZigBee network, or has
lost connection to its current ZigBee network.
- Flashes three times
The Power Switch has successfully bound with a controller
- Flashes five times
The Power Switch was unable to bind with a controller
Function Button Usage:
- Press the button to toggle on/off the Power Switch
- Press and hold the button for 10 seconds then release to reset the
Power Switch.
- Press and hold the button for 3 seconds then release to bind with
a controller
ZigBee Network Setup
Z
i
g
B
e
e
D
e
v
i
c
e
Z
i
g
B
e
e
D
e
v
i
c
e
ZigBee is a wireless communication protocol that is reliable, has low
power consumption and has high transmission efficiency. Based on
the IEEE802.15.4 standard, ZigBee allows a large amount of
devices to be included in a network and are coordinated for data
exchange and signal transmission.
J
o
i
n
i
n
g
t
h
e
Z
i
g
J
o
i
n
i
n
g
t
h
e
Z
i
g
As a ZigBee device, the Power Switch needs to join a ZigBee
network to receive commands and transmit energy consumption
information. Please follow the steps bellow to join the Power Switch
into a ZigBee network.
G
u
i
d
e
l
i
n
e
G
u
i
d
e
l
i
n
e
B
e
e
N
e
t
w
o
r
k
B
e
e
N
e
t
w
o
r
k
1
Case A
Case B
Case C
Advertisement
Table of Contents
Related Manuals for Climax Technology PSS-29ZBS
Summary of Contents for Climax Technology PSS-29ZBS
-
Page 1: Parts Identification
PSS-29ZBS Power Switch Introduction PSS-29ZBS is a ZigBee Power Switch. It is capable of receiving wireless signals from the coordinator in the Zigbee network to toggle On/Off of appliances that are attached to it. The Power Switch utilizes ZigBee technology for wireless signal transmission. ZigBee is a wireless communication protocol that is reliable, has low power consumption and has high transmission efficiency. - Page 2 1. Plug in the Power Switch into a power outlet. 2. Press and hold the function button for 10 seconds as the Power Switch resets and starts searching for existing ZigBee network. Please make sure the permit-to-join feature on the router or coordinator of your ZigBee network is enabled.
- Page 3 Unsigned Read 0x0003 HWVersion 8-bit 0x00 –0xff only integer Character Read 0x0004 ManufacturerName 0 – 32 bytes Climax Technology String only Character Read ModelIdentifier 0x0005 0 – 32 bytes PSS_00.00.00.14TC String only Character Read 0x0006 DateCode 0 – 16 bytes...
- Page 4 integer SceneValid 0x0003 Boolean 0x00 – Read 0x00 0x01 only 0x0004 NameSupport 8-bit bitmap x0000000 Read only Mandatory Identifier Name Type Range Access Default / Optional Read 0x0000 OnOff Boolean 0x00 –0x01 0x00 only Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Need help?
Do you have a question about the PSS-29ZBS and is the answer not in the manual?
Questions and answers