Download Print this page

VoxPrime VOX-100 SIP Installation Manual

Advertisement

Quick Links

Connections
Terminals 1&2 – MUSIC MUTE
When these two terminals are shorted together, the
music output of the amplifier will be muted to allow a
telephone page to be heard.
Terminals 3&4 – TEL INPUT (Balanced)
Connect to the telephone system page port.
This voice input can only be activated by the
telephone system page port dry contact or the
VOX circuit.
Terminals 5&6 or RCA Jacks – MUSIC IN
Connect a music source to these terminals noting
that pin 6 is a signal ground pin. It is important that
shielded cable be used to avoid any induced hum.
Use some RCA cables to connect the music source
using the RCA jacks.
Terminals 7&8 – CONTACT RING
Connect the night ringer relay of the PBX to these
terminals (dry contact activation).
Terminals 9&10 – TELEPHONE RING
Connect to a C.O. Port, analog telephone extension or to an ATA Module to activate the night ringer with a 90 Volts ringing signal.
Terminals 11&12 – 70V OUTPUT
Connect the speaker wiring to these terminals. Follow the guidelines for Class 3 Wiring.

Volume Controls

Music Volume
1
2
Music Bass
3
Music Treble

DIP Switches

1: TEL Off-Hook
ON position applies a telephone off-hook condition on the TEL INPUT. Some PBX page ports (e.g., Avaya) requires this condition.
2: Ring Cadence
ON position provides the night ringer audio ring cadence of 2 sec. ON / 4 sec. OFF, when a dry contact is applied to Contact Ring.
ON position Changes the output voltage from 70V to 25V.
3: 70V – 25V

LED Indicators

Power LED
The Power LED is ON when the equipment is connected to the AC electric outlet and is operational.
Peak Level LED
The Peak Level LED is ON when the output volume level has reached 70V.
Fault LED
Fault LED is ON when the amplifier is protecting itself from a faulty condition like a short circuit on the 70V output, overheat or an
overload.
Download our complete product manual PDF document at: www.voxprime.com/manuals
If you require technical assistance during installation, please call us : 1-888-633-2666
VOX-100 SIP Installation Guide
Dry Contact
4
Theses controls adjust
the volume, bass and
5
treble of the music
input source.
6

IMPORTANT NOTICE

© 2017 VOXPRIME All rights reserved
MUSIC
TEL
MUSIC
CONTACT
TEL RING
OUTPUT
T
MUTE
T
R
IN GND
R
OUT
RING
1 2
3 4 5
6 7
8 9 10 11 12 13
C.O. Port or
Page Port
Tel. Extension
(600 Ohms)
Dry Contact
Tel Volume
Theses controls adjust
the volume, bass and
Tel Bass
treble of the Telephone
page port.
Tel Treble
Rev:2
MUSIC
GND
VOL
BASS TREBLE
VOL
COM
MUSIC IN
MUSIC IN
Power
Peak Level
Fault
1
2
3
4
7
VOX
VOX Detection Sensitivity Control
8
Night Ringer
Ringing Volume
MODEL VOX-100 SIP
100 WATT AMPLIFIER
TEL
NIGHT
VOX
BASS TREBLE
RINGER
5
6
7
8
Aux Music
Source

Advertisement

loading
Need help?

Need help?

Do you have a question about the VOX-100 SIP and is the answer not in the manual?

Questions and answers

Summary of Contents for VoxPrime VOX-100 SIP

  • Page 1: Volume Controls

    Fault LED is ON when the amplifier is protecting itself from a faulty condition like a short circuit on the 70V output, overheat or an overload. IMPORTANT NOTICE Download our complete product manual PDF document at: www.voxprime.com/manuals If you require technical assistance during installation, please call us : 1-888-633-2666 © 2017 VOXPRIME All rights reserved...
  • Page 2 Play IP Button / Factory Reset Connect the VOX-100 SIP to the network using an Ethernet cable. Wait for about 1 minute and press the ‘’Play IP’’ button to optain the IP address provided by the network DHCP server. Pressing this button will play the device’s IP address through the amplifier Output (make sure that at least a speaker is connected in order to hear the IP address).