Mono Robin L Operating And Maintenance Manual

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Enter Serial No. here._____________________________________

In the event of an enquiry please quote this serial number.

www.monoequip.com

OPERATING AND MAINTENANCE

MANUAL

"ROBIN"

"L" SEALER

This machine is designed for use with Polypropylene (Polyolefin) films and is not

suitable for use with PVC or Polythene.

Robin L sealer RevA19 17-01-19

Table of Contents

Need help?

Do you have a question about the Robin L and is the answer not in the manual?

Questions and answers

Summary of Contents for Mono Robin L

Page 1 In the event of an enquiry please quote this serial number. www.monoequip.com OPERATING AND MAINTENANCE MANUAL “ROBIN” “L” SEALER This machine is designed for use with Polypropylene (Polyolefin) films and is not suitable for use with PVC or Polythene. Robin L sealer RevA19 17-01-19...
Page 2 Robin L sealer RevA19 17-01-19...
Page 3 Indicates a hazardous situation which, if not avoided, WARNING will result in electric shock. Indicates a hazardous situation which, if not avoided, CAUTION will result in minor or moderate injury. Robin L sealer RevA19 17-01-19...
Page 4 The switch disconnector must meet the specification requirements of IEC 60947. The supply to this machine must be protected by a 30mA RCD Robin L sealer RevA19 17-01-19...
Page 5 Failure adhere cleaning maintenance instructions detailed in this booklet could affect the warranty of this machine. Robin L sealer RevA19 17-01-19...
Page 6: Table Of Contents
1. INTRODUCTION 2. DIMENSIONS 3. SPECIFICATIONS 4. SAFETY 5. INSTALLATION 6. ISOLATION 7. CLEANING INSTRUCTIONS 8. ADJUSTMENTS 9. CONTROLS 10. OPERATING INSTRUCTIONS 11. MAINTENANCE 12. SPARES AND SERVICE 13. ELECTRICAL AND FAULT TRACING CONTACT INFORMATION Robin L sealer RevA19 17-01-19...
Page 7: Introduction
Whilst the ROBIN has been designed primarily for use in Catering operations with attention given to the ease of hygienic cleaning, the unit can also be effectively used for the packaging of non-food items. Robin L sealer RevA19 17-01-19...
Page 8 2.0 DIMENSIONS 742mm 519mm 585mm SIDE VIEW FRONT VIEW TOP VIEW Robin L sealer RevA19 17-01-19...
Page 9: Dimensions
Sealing pad surface material P.T.F.E. Operation only when sealing arm is within 3mm-4mm of sealing pads. This machine is designed for use with Polypropylene (Polyolefin) films and is not suitable for use with PVC or Polythene. Robin L sealer RevA19 17-01-19...
Page 10 For this reason it is recommended that all areas in the proximity of a fire should be immediately evacuated of all personnel and fire-fighters should be equipped with self-contained breathing apparatus. Robin L sealer RevA19 17-01-19...
Page 11: Safety
ROBIN and that any fumes given off are not toxic or harmful. Mono Equipment does not accept any liability whatsoever for any consequences arising from your choice of wrapping film.
Page 12: Installation
• Ventilation should be adequote to allow the small amount of fumes to be removed from the working area. • The sealer should be installed away from areas where the atmospheric conditions are such as to present a fire or explosion hazard. (dust ,flour etc.) Robin L sealer RevA19 17-01-19...
Page 13: Isolation
MAIN ISOLATION Before maintenance work or cleaning, unplug the machine from the mains socket. The machine's electrical supply is fused at the supply plug, which should be fitted with a 13 amp fuse when replacing. Robin L sealer RevA19 17-01-19...
Page 14: Cleaning Instructions
2. Wipe metalwork with a damp cloth and sanitising solution. 3. Check condition of sealing pads. (Replace if burn marks are excessive). 4. Check condition of sealing wires. (Clean off residual deposits with a stiff brush). Robin L sealer RevA19 17-01-19...
Page 15: Adjustments
On no account should too high a setting be used as this will reduce the life of both sealing wire and sealing pads and might give rise to unpleasant fumes. Robin L sealer RevA19 17-01-19...
Page 16: Controls
This component, which is a combined film splitting and product loading plate, can be slid in and out to suit the film width being used. SEALING PLATFORM. Flat wipe clean surface to hold the product whilst sealing. Robin L sealer RevA19 17-01-19...
Page 17: Operating Instructions
On no account should too high a setting be used as this will reduce the life of both sealing wire and sealing pads and might give rise to unpleasant fumes. Robin L sealer RevA19 17-01-19...
Page 18: Maintenance
Six Monthly (Electrical) Disconnect machine from Mains Electrical Supply and remove the Console rear cover. Inspect condition of wiring insulation and examine all terminals for security. Robin L sealer RevA19 17-01-19...
Page 19 If the rear of the transverse seal arm is not touching the seal pad, lower both bearings. d. If the transverse seal arm is touching the rear of the seal pad long before the front seal arm reaches the front seal pad, raise both bearings. ARM BEARINGS POSITION Robin L sealer RevA19 17-01-19...
Page 20 3mm to 4mm of touching the front seal pad. VIEW OF UNDERSIDE OF BODY SHOWING SWITCH "HEAT ON" SWITCH ADJUSTING NUT. ONE EACHSIDE VIEW OF UNDERSIDE OF BODY SHOWING SWITCH Robin L sealer RevA19 17-01-19...
Page 21 5. Repeat procedure for the side wire replacement. ALWAYS ensure that the front to back (side) wire lies over the front wire (looking up from below) at the crossover point. TENSION SPRING WIRE Robin L sealer RevA19 17-01-19...
Page 22: Spares And Service
1 - Roll 13mm wide P.T.F.E. Glass Tape (1.2Mtrs) – Pt No A900-12-120 1 - Packet 13 amp. Fuses (10) –----------------------- Pt No B842-85-011 For these and other spares please contact Mono spares dept. Tel. 01792 564039 Robin L sealer RevA19 17-01-19...
Page 23 TRANSFORMER BEARING CONTACTOR B836-07-006 B878-91-001 SWITCH SIMULATOR A900-19-099 WIRE TENSION SPRING A900-18-098 FOOT 481-03-00001 PAD 481-02-00005 CHANNEL 481-03-00002 PAD 481-02-00006 CHANNEL B842-07-026 A900-33-011 “HEAT ON” SWITCH FILM ROLLER AND SPINDLE A900-19-098 ARM RETURN SPRING UNDER Robin L sealer RevA19 17-01-19...
Page 24 13.0 ELECTRICAL Robin L sealer RevA19 17-01-19...
Page 25 Look for break in wire. Seal wire or clamp screw shorting on arm. Insulation strip missing. Look for burn marks. Supply wire bare and shorting to frame. Short circuit in control console. See also “Wires burning out”. Robin L sealer RevA19 17-01-19...
Page 26 Tension on film does not Relax tension on film weld. permit seal during cut- when sealing. off. Seal wire insulation strip Continued use of Replace insulation badly burnt. excessive heat. strips. Maintenance schedule not followed. Robin L sealer RevA19 17-01-19...
Page 27 Queensway Swansea West Industrial Estate Swansea. SA5 4EB UK Tel. 01792 561234 Fax. 01792 561016 Mono spares dept. Tel. 01792 564039 Email:marketing@monoequip.com Web site:www.monoequip.com MONO ROBIN DISPOSAL Care should be taken when the machine comes to the end of its working life. All parts should be disposed of in the appropriate place, either recycling or other means as the law permits at the time.

This manual is also suitable for:

Robin