Advertisement
Table of Contents
- 1 Standard
- 2 Standard Models Important Features
- 3 1 Phase Gray Box Electrols Upgrade
- 4 1 Phase Gray Box Electrols
- 5 S1 Electrols
- 6 3 Phase Gray Box Electrols Upgrade
- 7 3 Phase Gray Box Electrols
- 8 Motor Starter
- 9 Bulldog
- 10 Bulldog Models Important Features
- 11 Bison
- 12 Bison Models Important Features
- 13 S1 Electrols PC Board Replacement
- 14 Bulldog Model S1 Electrols
- 15 3 Phase Motor Start-Up
- Download this manual
Standard MODELS
• 550
• 1400
Bulldog MODELS
• 550
• QT
• QT E
Bison MODELS
• BISON
• BISON E
E
F
F
I
C
I
E
N
ELECTROLS UPGRADE AND REPLACEMENT
How to properly upgrade the gray box Electrols to S1
Electrols, and how to replace the S1 Electrols PC Board
(955.xxxx.xxx)
(914.xxxx.xxx)
*Note: Instructions relating to Standard 1400 models also apply to Standard 1200 and 2800 models.
(855.xxxx.xxx)
(809.xxxx.xxx)
(809E.xxxx.xxx)
(818.xxxx.xxx)
(826.xxxx.xxx)
(818E.xxxx.xxx)
(826E.xxxx.xxx)
C
Y
I
N
D
E
SERVICE INSTRUCTION
Important Features
3 Phase Motor Startup
Important Features
1 Phase Gray Box Electrols Upgrade
3 Phase Gray Box Electrols Upgrade
3 Phase Motor Startup
Important Features
1 Phase Gray Box Electrols Upgrade
3 Phase Gray Box Electrols Upgrade
S1 Electrols PC Board Replacement
3 Phase Motor Startup
N
T
I
S
T
R
Y
®
Procedures
Page
2
3
4
15
Procedures
Page
6
7
8
14
15
Procedures
Page
10
11
12
14
15
Advertisement
Table of Contents
Related Manuals for RAMVAC BISON
Summary of Contents for RAMVAC BISON
- Page 1 • QT E (809E.xxxx.xxx) Procedures Page BISON MODELS • BISON Important Features (818.xxxx.xxx) 1 Phase Gray Box Electrols Upgrade 3 Phase Gray Box Electrols Upgrade (826.xxxx.xxx) S1 Electrols PC Board Replacement 3 Phase Motor Startup • BISON E (818E.xxxx.xxx) (826E.xxxx.xxx) ®...
- Page 2 STANDARD Standard Models Important Features Page 2...
- Page 3 STANDARD 1 Phase Gray Box Electrols Upgrade 1 Phase Gray Box Electrols How to upgrade gray box Electrols to S1 Electrols on all Note: Gray Box Electrols have several variations 1 phase Standard models. Moisture Probe Wires Remote Switch Wires P1, P2 Power Source Wires R1, R2, RL...
- Page 4 STANDARD 3 Phase Gray Box Electrols 3 Phase Gray Box Electrols Upgrade Note: Gray Box Electrols have several variations Moisture Probe Wires P1, P2 Power Source Wires Remote Switch Wires L1, L2, L3, GND How to upgrade gray box Electrols to S1 Electrols on all R1, R2, RL 3 phase Standard models.
- Page 5 NOTES Page 5...
- Page 6 BULLDOG Bulldog Models Important Features Page 6...
- Page 7 BULLDOG 1 Phase Gray Box Electrols Upgrade 1 Phase Gray Box Electrols Note: Gray Box Electrols have several variations How to upgrade gray box Electrols to S1 Electrols on all Moisture Probe Wires Remote Switch Wires P1, P2 Power Source Wires 1 phase Bulldog models.
- Page 8 BULLDOG 3 Phase Gray Box Electrols Upgrade 3 Phase Gray Box Electrols Note: Gray Box Electrols have several variations Moisture Probe Wires How to upgrade gray box Electrols to S1 Electrols on 3 P1, P2 Power Source Wires Remote Switch Wires phase Bulldog models.
- Page 9 NOTES Page 9...
- Page 10 BISON Bison Models Important Features Page 10...
- Page 11 Remote Switch Wires Power Source Wires R1, R2, RL L1, L2, GND 1 phase Bison models. 1. Secure Disconnect. 2. Remove items from gray box Electrols. a. Disconnect power source wires from L1, L2, and GND. Remove cord grip and power source wires from gray box Electrols.
- Page 12 Connect supplied extensions to wires and connect to terminals. Motor Wires 2T1, 4T2, Motor Control Wires 6T3, Motor Ground Note: See Bison Reservoir Swtches illustration on previous C1, C2, C3, GND page for specific locations. i. Connect the oil switch wires to terminals 1 and 2 on terminal S1 Electrols plug “12DE34”.
- Page 13 NOTES Page 13...
- Page 14 10. Install cover using screws previously removed. 11. With proper orientation, insert terminal plugs into S1 Electrols. Motor Wires Power Source Wires Bison Model S1 Electrols Electrical Specification Label 3 Phase Wiring 1 Phase Wiring Motor Control Wires...
- Page 15 Clean any oil or debris out of Filtrols. 4. Complete 3 phase motor start-up a. Standard Models: Reinstall Filtrols inlet line b. Bulldog and Bison Models: Reinstall main air filter and Bison and Bulldog Models vacuum controller. Vacuum Controller...
- Page 16 NOTES 3100 First Avenue Phone: 1-800-5-RAMVAC SOF_7.2.3-01-139.doc Spearfish SD 57783 USA 1-605-642-4614 Effective Date: 25-Oct-05 Web: ramvac.com Fax: 1-605-642-3776 Page 16 of 16...