Remote LED lights ON/OFF and dimming control individually or by group Download the free Boost Android or iOS App to explore even greater functionality Box Contents One A01-A60 Bulb User Manual Limited Written Express Warranty Product Specifications ...
Page 2
Operating Humidity: 10% ≤ RH ≤ 95%, Non condensation Atmospheric Pressure: 86kPa ~ 106kPa Colour: Neutral White Dimensions: 120mm (H) x Φ 60mm (Dia.) Weight: 290g (approx.) Spécifications de produit (par ampoule) • Alimentation: 100 ~ 230V AC, 50/60 Hz •...
Page 4
5. Launch the boost by Sengled application, and a 'Welcome' page appears. At the beginning, press the "network" tab to initialize boost A01-A60 bulb's configuration. After that, click the “START” button to enter the configuration and control interface of the bulb/s.
Page 5
If there is no any equipment, please check if the lamp is powered on, and click the refresh button to try again. 8. The App will also search and list out nearby available boost A01-A60 bulb/s. The default SSID of the bulb is “SENGLED_AP”. (ATTENTION: Figure shows below, SSID Name of "LL_AP_00_**"...
Page 6
bulbs, the interface shows a Main Control Page. This can be used to control the overall LED light dimming and ON/OFF. 11. To control the LED bulb individually, pull up the bulb list at the bottom, each bulb can be dimmed separately. Click the arrow on the right, and it goes to the bulb wireless network configuration page.
Page 7
(such as MAC address). User can change bulb's SSID (listed on the WLAN table, visible name to public), or Name (listed on the boost by Sengled App) to a more meaningful name, such as "Living Room AP" or "Living Room Wi-Fi". Press "Apply"...
Page 8
13. If re-configuration of the wireless network is needed, press the Setting Menu button on the Main Control Page and click the "Network" tab. Re-initialize all bulbs on the network and start setup wizard again. 14. If the bulb cannot be detected by the portable smart devices or App in any ways, user can press the physical RESET button to reset the configuration of the bulb (in the middle of the LED lens), as shown below.
• Heed all warnings contained within these instructions. • Please follow all user manual instructions when installing the product. • Clean SENGLED product only with a dry towel. • This Product is intended for indoor use only. • Do NOT use this product outdoors.
Page 10
4) the product has been exposed to rain or moisture, 5) the product does not operate normally, or has been dropped. • Repairs must be performed by a qualified SENGLED technician. • For bulb with a weight significantly higher than that of the bulbs for which they...
Page 11
Warranty Information Warranty statement For this product, the manufacturer grants a warranty of 2 years for workmanship and material. Warranty repairs may be performed exclusively by an authorised customer service. The original sales receipt has to be enclosed as proof. Excluded from this warranty are: normal wear and tear, alterations, rework, damage as a result of carelessness, outside influence, areas of application for which the product is not intended, or products that have been dismantled completely or partially.
Page 12
FCC STATEMENT FOR USERS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 13
co-located or operated in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions to satisfy RF exposure compliance.
Page 14
IC Radiation Exposure Statement for Canada This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s'il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne.