Advertisement
Advertisement
Summary of Contents for erlab Halo Sense Smart VOC
- Page 1 Installation & User Manual Simpler Halo Sense Smart VOC/A/F Air quality monitor...
-
Page 2: Table Of Contents
Halo Sense Smart Contents General information ....................3 Safety notices .........................3 Product registration ....................3 Description of the unit ...................4 Installation ..........................6 - Wall installation - Bench installation - Sensors sensitivity settings Connectivity principle ....................9... -
Page 3: General Information
Take full advantage of the devices connectivity to enhance your safety Warranty Please register your product at www.erlab.com. This will ensure that you receive important information about your product. Warranty applicability is subject to Erlab© general terms and conditions • The registration and/or connection of the product shall be performed within twelve months from the purchase date •... -
Page 4: Description Of The Unit
Halo Sense Smart Description of the unit Front view Side view Rear view with wall-mount plate Rear view without wall-mounting plate... - Page 5 User Manual Details Front of the unit Smart-Light that pulses when in alarm Halo Sense Smart model indicator : Green (VOCs), Blue (Acids), Purple (Formaldehyde) Wall-mount plate Location of screw holes when mounting to a wall Connection points to the unit Grommet Power wire grommet Plate/Box anchorage points...
-
Page 6: Installation
Halo Sense Smart Installation Halo Sense Smart is a static air quality monitor Detection of pollutants is only possible when the sensor is in contact with pollutants present in the air Recommended installation: Non recommended installation: - Place as close as possible to the source of fumes/vapors - Ceiling - At the height of respiratory tract - Pollution source remote area... - Page 7 User Manual Installation on a wall Attaching the plate to the wall 122 mm 4.8 in Tools and hardware needed (not included). 5 mm 3 in 122 mm...
-
Page 8: Sensors Sensitivity Settings
Halo Sense Smart Sensors sensitivity settings Settings recommended by Erlab Halo Sense Smart – VOC model High Medium-High Medium Medium-Low PEL/TWA 8H PEL/STEL Chemical sensitivity sensitivity sensitivity sensitivity sensitivity (ppm) (ppm) (ppm) (ppm) (ppm) (ppm) (ppm) Ammonia Hexane Xylene Acetonitrile... -
Page 9: Connectivity Principle
User Manual Connectivity principle Ecosystem designed for simpler use and safer protection Embedded Embedded Embedded Embedded service service service service Storage cabinet Air purifiers Air quality monitors Fume hood Ethernet-TCP-IP Internet network and/or local area network (LAN - for eGuard PC only) Database eGuard app Monitoring... - Page 10 Capability Monitoring + Controlling Monitoring Monitoring + Controlling Data access One unit Multiple units Multiple units Historical data access Historical data download Alerts Monitor multiple units Multiple user accounts Automatized status report (except if local connection) Download available on www.erlab.com...
- Page 11 « Settings » using the following credentials: : If the page is not accessible, refer to the Login : erlab / Password : smart procedure on pages 12-16 If the page is accessible, refer to page 17...
- Page 12 Halo Sense Smart Modify computer network parameters Network parameters Right click Left click...
- Page 13 User Manual Access the network and sharing center Left click Access the network connection This confirms your WIFI is disconnected! Right click Left click to access properties...
- Page 14 Halo Sense Smart Enter compatible network parameters as indicated below Left click Left click...
- Page 15 Open your web browser again, then type the following IP address 192.168.0.200 OK : You are connected to the embedded software • You enter the « Status » page and you can have access to the « Settings » using the following credentials: Login : erlab / Password : smart...
- Page 16 Halo Sense Smart Administrator interface Status page details Choose active interface page Device ID: Model Device ID: serial number, MAC address, device status When this button is clicked, the unit’s Smart-Light will pulse Air quality gauge: indicates the air quality level (green: good air quality / Red: polluted air) Unit usage time since inception Air quality and sensor replacement alarms...
- Page 17 User Manual Access the settings by using the following: User name: erlab Password: smart...
- Page 18 Halo Sense Smart Settings page details Device time and date settings Device network settings Mode: Selected IP protocol Hostname: Device name on network IP: IP address of the device MASK: network mask GW: Network gateway Activate/Deactivate the exchange of information This allows the transmission of information from the device to the eGuard server for: - remote monitoring via eGuard App (mobile &PC) - receive usage reports...
- Page 19 User Manual Device History Displays the device’s event log Used for downloading the log in .csv format...
- Page 20 We provide safety, we protect your health Erlab invented the ductless fume hood in 1968. With more than 45 years of experience in the field of chemical filtration and protection of laboratory personnel; we know the formula for safety. With Erlab, you will never have to wonder or worry if our products are safe.
Need help?
Do you have a question about the Halo Sense Smart VOC and is the answer not in the manual?
Questions and answers