extronics iTAG 100 Operating Manual
  1. Manuals
  2. Brands
  3. extronics Manuals
  4. Other
  5. iTAG 100
  6. Operating manual

extronics iTAG 100 Operating Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Operating Manual
iTAG100

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iTAG 100 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for extronics iTAG 100

  • Page 1 Operating Manual iTAG100...
  • Page 2 This page is intentionally left blank. 314344 Document Number (See Last Page for Revision Details) ©2006 Extronics Limited. This document is Copyright Extronics limited. Extronics reserve the right to change this manual and its contents without notice, the latest version applies.

  • Page 3: Table Of Contents

    Operating Manual Contents Introduction......................4 Safety Information and Notes ................5 Storage of this Manual ................. 5 Essential health and safety requirements............. 5 List of Notes ....................5 Installation and Setting-to-Work ................7 Assembly and Disassembly ................. 7 Installation ....................7 Adjustment ....................

  • Page 4: Introduction

    Operating Manual 1 Introduction The iTAG 100 is an intrinsically safe version of the AeroScout T2 Tag and is the most advanced Wi-Fi based Active RFID tag on the market, from the company that originated the Wi-Fi tag industry. The iTAG 100 is a small, long-life Wi-Fi based Active RFID device that can be placed on any asset, allowing the AeroScout system to locate assets that are not Wi-Fi enabled.

  • Page 5: Safety Information And Notes

    Operating Manual 2 Safety Information and Notes 2.1 Storage of this Manual Keep this user manual safe and in the vicinity of the controller. All persons who have to work on or with the controller should be advised on where the manual is stored. 2.2 Essential health and safety requirements This equipment is designed to satisfy clause 1.2.7 of the Essential Health and Safety Requirement ANNEX II of directive 94/9/EC.
  • Page 6 Operating Manual Warning! iTAG100 batteries should only be replaced in the safe area, by a competent person who is approved by the manufacturer. Important! The device contains no user serviceable parts. Important! Any repairs or replacement of parts MUST be performed by the manufacturer or its nominated sub-contractor or agent.

  • Page 7: Installation And Setting-To-Work

    Operating Manual 3 Installation and Setting-to-Work 3.1 Assembly and Disassembly The iTAG100 is provided ready assembled and should not be dismantled by the user. 3.2 Installation The iTAG100 should be mounted on the asset which desires tracking or worn by the person who is to be tracked.

  • Page 8: Intended Purpose Usage

    Operating Manual 4 Intended Purpose Usage Important Before setting the units to work, read the technical documentation carefully. Important The latest version of the technical documentation or the corresponding technical supplements is valid in each case. The iTAG100 is built using modern components and is extremely reliable in operation;...

  • Page 9: Safety Precautions

    Operating Manual 4.4 Safety Precautions Important For the installation, maintenance and cleaning of the units, it is absolutely necessary to observe the applicable regulations and provisions concerned with explosion protection (EN 50014, EN 50020) as well as the Accident Prevention Regulations. 4.5 Cleaning and Maintenance Intervals The cleaning intervals depends on the environment where the system is installed.

  • Page 10: Type Codes

    Operating Manual 5 Type Codes 5.1 iTAG100. Part Number Description iTAG100-IIB iTAG100 suitable for use in a IIA and IIB Gas hazardous area. iTAG100-IIB-CB iTAG100, fitted with a call button, suitable for use in a IIA and IIB Gas hazardous area. iTAG100-IIC iTAG100 suitable for use in a IIC, IIB and IIA Gas hazardous area.

  • Page 11: Certification

    Operating Manual 6 Certification...
  • Page 12 Operating Manual...
  • Page 13 Operating Manual...
  • Page 14 Operating Manual...
  • Page 15 Operating Manual...
  • Page 16 Operating Manual...
  • Page 17 Operating Manual...
  • Page 18 Operating Manual...
  • Page 19 Operating Manual...

  • Page 20: Label Drawing

    Operating Manual 7 Label Drawing...
  • Page 21 Operating Manual...

  • Page 22: Manual Revision

    Operating Manual 8 Manual Revision Revision Description Date Atex Certification 27/7/06 Added new picture on front cover 16/10/06 Added new picture on front cover 19/04/07 Added EC Declaration 05/06/07 Amendments Made 23/12/08 Digitally signed by Nick Saunders Nick Saunders DN: CN = Nick Saunders, C = US Reason: I am approving this document Date: 2008.12.23 16:51:48 Z...

Table of Contents