Related Manuals for McIntosh MTI100
Summary of Contents for McIntosh MTI100
- Page 1 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 www.mcintoshlabs.com MTI100 Integrated Turntable Owner’s Manual...
- Page 2 FCC requirements. deux conditions suivantes : (1) il ne doit pas produire de RoHS: 2011/65/EU Modification not expressly approved by McIntosh may brouillage, et (2) l’utilisateur du dispositif doit être prêt ErP: EC regulation 1275/2008 and its frame work void your authority, granted by the FCC, to use the à...
-
Page 3: Table Of Contents
Thank you from all of us at McIntosh Table of Contents Turntable Maintenance ......... 9 Thank you from all of us at McIntosh ....3 You have invested in a precision instrument that will Clean Your Stylus ..........9 Make a Note ............3 provide you with many years of enjoyment. -
Page 4: Inside The Box
Inside the Box protect the Stylus, it is best to leave the Stylus Guard installed while setting up or moving the MTI100. But Open the top of the shipping carton. when the time comes to unleash the Stylus, you can Remove the top layer of shipping foam. -
Page 5: Installing The Wi-Fi Antenna
Please use care and an appropriate tool for side (looking at the back) of the rear of the MTI100 unsecured from its packing and hooked on the connecting or disconnecting these wires. Since the (Figure 8 on page 7). -
Page 6: Installing The Belt
Belt (Figures 12 and 13 on page 9). The MTI100, and there is no real benefit to doing this. wider position is 45 rpm and the position above is Effective lighter options exist in the world if you wish to employ record clamps. -
Page 7: Making Connections
Discovery mode. You do not need to do anything be connected to speakers, other sources, additional to give a final 90 degree turn. more to the MTI100 than turn it on. To pair the amplifiers, power control, and AC power. Do not over tighten. -
Page 8: More Outputs
The Main Output allows the use of a separate external power amplifier. To use a separate power Headphones amplifier instead of the MTI100’s integrated On the right side of the front of the MTI100 is a amplifier: 1/4-inch Headphone Jack. To listen to headphones, •... -
Page 9: Input Knob
Only use a back to front MIN light will flash. Remember, Pushing and motion when contacting the stylus during cleaning. Holding the Volume Knob will place the MTI100 in Standby when the unit is on. Anti-skate... -
Page 10: Belt Pulley- 50Hz Verses 60Hz
Cartridge Alignment The cartridge has been expertly aligned at our factory. You do not need to align the cartridge when first setting up the MTI100.We do include an Alignment Jig for for setting up a new cartridge. To align a cartridge: Figure 14–... -
Page 11: Dimensions
Dimensions 19-1/4 inches 48.9cm Front View of MTI100 Headphone Jack 13 inches 33.02cm 14 inches 35.2cm 5-1/2 inches 14cm 6-3/4 inches Side View 17.15cm of MTI100 8 inches 20.3cm... -
Page 12: Description Of Remote Control Buttons
POWER OFF, INPUT (Down), PH, BT, AUX, OPT (Optical), and COAX. Contact McIntosh Technical Figure 15– Remote control diagram Assistance or your dealer for more information. Some buttons, like the CD-related buttons or the unlabeled arrow keys, may be used to control other connected McIntosh products. -
Page 13: Changing The Remote's Battery
To open the remote: • Hold the remote upsidedown and backwards with McIntosh name upsidedown and facing away from you. The thicker end will now be the top and Figure 16– Sliding open the remote you should be staring at the back of the remote. -
Page 14: Technical Specifications
Technical Specifications Greater than 100, 4 ohm load Digital Input Sample Rates Optical: 16Bit, 24Bit - 32kHz to 192kHz Input Impedance Amplifier Coaxial: 16Bit, 24Bit - 32kHz to 192kHz 6.5K ohms Power Output Bluetooth Profiles Voltage gain 50 watts into 8 ohm loads A2DP, AVRCP, SBC, HD 22dB 80 watts into 4 ohm loads... -
Page 15: Tone Arm
General 9” vertical Yoke type tonearm with lateral type Power Requirements bearing Refer to the rear panel of the MTI100 for the Damped machined aluminum tube arm correct voltage. The MTI100 is factory configured for one of thefollowing AC Voltages:... - Page 16 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 www.mcintoshlabs.com The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.S.A. McIntosh Part No. 04188000...