Summary of Contents for Control Technology Inc. CTI 3570 Series
- Page 1 CTI 3570 SERIES INDUSTRIAL ETHERNET SWITCH INSTALLATION AND OPERATION GUIDE Version 1.0 CTI Part # 062-00355-010 3570IOG 102402...
- Page 2 Copyright 2002 Control Technology Inc. All rights reserved. This manual is published by Control Technology Inc., 5734 Middlebrook Pike, Knoxville, TN 37921. This manual contains references to brand and product names which are tradenames, trademarks, and/or registered trademarks of Control Technology Inc. Other references to brand and product names are tradenames, trademarks, and/or registered trademarks of their respective holders.
-
Page 3: Table Of Contents
TABLE OF CONTENTS CHAPTER 1. DESCRIPTION ..................1 1.1. Introduction..................... 1 1.2. Power Supply..................1 1.3. Ethernet Ports..................2 1.4. LED Indicators..................2 CHAPTER 2. INSTALLATION.................3 2.1. Unpacking ....................3 2.2. Mounting on the DIN rail................3 2.3. Connecting Power ................... 4 2.4. -
Page 5: Chapter 1. Description
This reduces the chance of damaging the 3570 circuitry from power surges occurring on external power lines. The input power specification is: 11-32VDC Power is connected to the 3570 using the connector at the top of the case. CTI 3570 Series Installation and Operation Guide... -
Page 6: Ethernet Ports
ON – there is a good connection to a device, but no data is being transmitted or received FLASHING - a good connection exists and data is being transmitted 10/100 LEDs (1 per port) OFF - connection is 10Mbit/s ON – connection is 100Mbit/s CTI 3570 Series Installation and Operation Guide... -
Page 7: Chapter 2. Installation
To remove the unit, insert a screwdriver into the red tab and pry the tab outward until the lock in released, then rotate the unit upward and lift off. Figure 4. Removing the 3570 from the Figure 3. Attaching the 3570 to the DIN DIN rail rail CTI 3570 Series Installation and Operation Guide... -
Page 8: Connecting Power
3570. Push the plug into the jack until the plug clicks into place. To remove the plug, simply depress the latching Figure 7. RJ45 and MTRJ cables on tab and pull the plug out of the jack. 3570-1F CTI 3570 Series Installation and Operation Guide... -
Page 9: Checkout
2. Verify P2 LED is ‘ON’ if a second power supply is connected 3. Verify LINK/ACT LEDs are on or blinking for ports connected to active devices 4. Verify 10/100 LEDs are ‘ON’ for ports connected to 100Mbit devices CTI 3570 Series Installation and Operation Guide... -
Page 10: Chapter 3. Troubleshooting
CTI for repair. 4. Verify continuity of Ethernet fiber or copper cables. Plug a known good device and cable into each of the ports and make sure the LINK/ACT light for that port comes on. CTI 3570 Series Installation and Operation Guide... -
Page 11: Chapter 4. Product Specifications
140 Storage Temperature: -40 to 85 C (-40 to 185 Relative Humidity: 5% to 95% (non-condensing) Agency Approvals Pending: UL, ULC, Class 1, Div. 2, CE Shipping Weight: 1.0 lb. (0.45 Kg) CTI 3570 Series Installation and Operation Guide... -
Page 12: Chapter 5. Port And Switch Specifications
Broadcast storm protection: limits to 25% Buffer memory: 128K Buffers (total): 1024 Buffers per port: 205 Buffer size: 128 bytes Illegal frames: dropped per IEEE 802.3 Late collisions: dropped after 512 bit times CTI 3570 Series Installation and Operation Guide... -
Page 13: Limited Product Warranty
CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE. CTI 3570 Series Installation and Operation Guide... -
Page 14: Repair Policy
Failure to observe static control precautions may void the warranty. For additional information on static control precautions, contact CTI's main office at 1-800-537-8398. CTI 3570 Series Installation and Operation Guide...
Need help?
Do you have a question about the CTI 3570 Series and is the answer not in the manual?
Questions and answers