Subscribe to Our Youtube Channel
Related Manuals for Harris TS350
Summary of Contents for Harris TS350
- Page 1 ® TS350 Basic Rate Euro ISDN Test Set User's Guide V2 Free Datasheet http://www.Datasheet4U.com...
- Page 2 Whilst every effort has been made to ensure the accuracy of this User's Guide at the time of printing, Harris Corporation will not be liable for any errors.
-
Page 3: Table Of Contents
RS232 Serial Port..............18 Powering.................19 Low Battery Warning ...............20 Charging the NiMH Batteries ............20 Using Alkaline Batteries ............20 TS350 Configuration Modes ............21 ISDN S - TE ................21 ISDN S - Monitor ..............22 ISDN U - TE................22 PSTN..................22 ISDN BRI Testing................23 BER Test ................23... - Page 4 ..............60 Layer 2 messages ..............60 Layer 3 Messages ..............61 B Channel Status ..............62 Clear Cause.................62 Passive Monitor ................63 PSTN Testing ................66 TS350 Firmware Upgrade ............68 TS350 Specifications ..............70 Protocol ..................70 Interface................70 Power ..................70 Display ...................70 RS232 Port ................70 Free Datasheet http://www.Datasheet4U.com...
- Page 5 ® TS350 Basic Rate Euro ISDN Test Set Weight ..................71 Environmental .................71 Dimensions ................71 Safety ..................71 CE..................71 APPENDIX.................72 User messages ...............72 Layer 1 INFO States ..............72 Layer 1 Error message ............72 Layer 2 Frame types.............72 Layer 2 Error Messages............73 Layer 3 Message Types............73...
-
Page 6: Ts350 Package
ISDN basic rate lines. The TS350 can make an ISDN speech, data, or BERT call. It can monitor the protocol on the ISDN line and when used with the Genius ISDN Protocol Analyser software it makes an extremely powerful maintenance tool. -
Page 7: Quick Start
Battery Charging The AA size NiMH batteries are shipped uncharged so first you must charge your TS350 NiMH batteries. Insert the dc plug of the mains plug top dc battery charger into the dc socket at the bottom end of the unit. -
Page 8: Making A Ber Test
Note: For more detail on these options and their use see the appropriate section in this User's Guide. To make your first BERT call: Step 1 Connect your TS350 with the RJ45 to RJ45 lead to the NT interface S/T bus socket. Step 2 Switch on the TS350 by holding down the key for 2 seconds. - Page 9 ® TS350 Basic Rate Euro ISDN Test Set Step 3 ↵ ↵ Select BER Test by pressing 14:20 Test Menu BER Test Speech 3.1kHz Audio Teleservices Step 4 Select BERT from the BER test menu 14:20 BER Test BERT Bearer:Data...
- Page 10 Loopbox menu settings which are intended for incoming BERT calls from another tester. The TS350 displays the BERT test results menu and the test will be automatically ended after the test time, in this case 1 minute.
-
Page 11: Making A Speech Call
(approximately 2 seconds). Making a Speech Call Step 1 Connect your TS350 with the RJ45 to RJ45 lead to the NT S/T interface socket. Step 2 Switch on the TS350 by holding down the key for 2 seconds. The TS350 turns on, beeps and displays its start up screen sequence. - Page 12 ® TS350 Basic Rate Euro ISDN Test Set Step 5 Enter the B channel number (default is 1) on which to make an ↵ ↵ outgoing and press 14:20 Speech Call Enter B ch#: 1 Dial: Overlap Step 6 You are prompted to Enter number: Enter the number you wish to dial.
-
Page 13: Receiving A Voice Call
® TS350 Basic Rate Euro ISDN Test Set Receiving a Voice Call When your TS350 receives a compatible incoming Setup message (incoming call) it will ring the sounder and prompt you with the screen: 14:20 Test Menu Incoming call... 01273860000... -
Page 14: Ts350 Operation
64 pixels. When operated only on the batteries, the backlight will turn on after each key press and turn off after one minute. If the TS350 is powered from the dc supply, then the backlight will remain on all the time. -
Page 15: Led Indicators
® TS350 Basic Rate Euro ISDN Test Set LED Indicators 14:20 Test Menu BER Test Speech 3.1kHz Audio Teleservices L2 USR RR_C TEI=74 L3 NET SETUP Flashes green when the B1 channel is active. The LED is Off when the B1 channel is not in use. -
Page 16: Key Functions
® TS350 Basic Rate Euro ISDN Test Set Key Functions Number keys: • Enter dialled digits. • Select menu items irrespective of cursor position. • KEYPAD IE: during an ISDN call numbers are sent as keypad information elements if KEYPAD is selected. - Page 17 Select a reverse contrast menu item. • Select a reverse contrast function. • Dial a reverse contrast number. • Press and hold > 2 second to switch on the TS350. • Press and hold > 2 seconds to turn off the TS350. Free Datasheet http://www.Datasheet4U.com...
-
Page 18: Connectors
Pins 7,8 PS2 RS232 Serial Port 9 way D female Baud rate 115200 Data bits: Parity: none Stop bits: Flow control: Xon/Xoff Pin out: connected to 4 and 6 TS350 transmit data TS350 receive data connected 1 and 6 Free Datasheet http://www.Datasheet4U.com... -
Page 19: Powering
The normal mode of operation sends a Genius software compatible binary output of the D channel protocol. In ISDN S-TE and ISDN U- TE mode this protocol is the TS350 to Network protocol; in ISDN S- Monitor passive monitor mode this is D channel protocol generated by the TE and the Network. -
Page 20: Low Battery Warning
To charge the NiMH batteries, insert the plugtop supply into a convenient mains socket and insert the dc jack into the TS350 dc socket. If the TS350 is not already on, it will turn on immediately. Leave the TS350 to charge for approximately 16 hours. Whilst the dc plugtop supply is on you will see a plug icon in the top right hand corner of the LCD. -
Page 21: Ts350 Configuration Modes
In this mode the TS350 will act as an ISDN terminal connected to the four wire S/T bus. The TS350 can carry out a BERT test on any bearer, make a voice call, carry out manual or automatic tests for Teleservice network support and common Supplementary F r e e D a t a s h e e t h t t p : / / w w w . -
Page 22: Isdn S - Monitor
Mode menu. ISDN S - Monitor In this mode the TS350 is "bridged" onto the S bus link between the TE and the NT. The TS350 passively monitors D channel messaging in bothTE to NT and NT to TE directions. The binary decode is output on the RS232 port in real time for decode with the Genius ISDN Protocol Analyser software. -
Page 23: Isdn Bri Testing
® TS350 Basic Rate Euro ISDN Test Set ISDN BRI Testing The ISDN Test Menu is available in the ISDN S - TE mode and the ISDN U - TE modes. BER Test The BER (bit error rate) test is selected from the Test Menu which is presented after you have selected ISDN BRI - TE from the Mode menu. - Page 24 ® TS350 Basic Rate Euro ISDN Test Set 14:20 BER Test BERT Bearer:Data Loopbox:Bearer Pattern: 2 ↵ ↵ 14:20 BER Test Enter B ch#: 1 14:20 BER Test Enter Number: 01633123456 ↵ ↵ L2 USR INFO TEI=0 L3 USR SETUP...
- Page 25 ® TS350 Basic Rate Euro ISDN Test Set The test results are shown in real time: • E is the bit error count • ES is the errored second count • SES is the severely errored second count • Time left is shown counting down from the preset test time, (or if Cont is set in the BERT setup options then the Test time counts up).
-
Page 26: Ber Test Options
® TS350 Basic Rate Euro ISDN Test Set To clear the results screen and return to the BER test menu press key. BER Test Options The BER test sub menu options are listed in the BER test menu. Using the scroll down arrow key you can see all the options. -
Page 27: Loopbox
In this mode the TS350 cannot clear the incoming call, which must be cleared by the remote tester. This is to avoid tampering when the TS350 is left unattended. - Page 28 None: No incoming calls are looped. In this mode all calls are manually answered. Voice calls operate normally. ManPRBS: If an incoming call compatible with the selected bearer in the Bearer menu is received the TS350 will ring. When you answer ↵ ↵ the call with the key, the TS350 sends its own PRBS pattern as selected in the Pattern menu.
-
Page 29: Pattern
TS350 Basic Rate Euro ISDN Test Set The TS350 cannot clear the incoming call, which must be cleared by the remote tester. This is to avoid tampering when the TS350 is left unattended. Note: Scroll down the menu pressing the key to highlight Auto PRBS for selection. -
Page 30: Results
® TS350 Basic Rate Euro ISDN Test Set User: Allows you to set your own standard test time by entering your selected time in the sub menu: 14:20 BER Test C=Abort Accept Value Time- hh mm 01:30 To enter the test time enter the full time including leading zeros with the hours first e.g. -
Page 31: Test Thresholds
® TS350 Basic Rate Euro ISDN Test Set Test Thresholds Sets the error level that will be treated as a BERT failure. You can either set the error level as a number of bit errors, or to be G.821 values. If you select G.821 values, the occurrence of any one of the three values during the test will result in a test failure. - Page 32 ® TS350 Basic Rate Euro ISDN Test Set Note: Some iSPBXs will only allow a Setup message with any channel specified. 14:20 Speech Call Enter B ch#: 1 Dial: Overlap ↵ ↵ Key in the digits of the number you wish to call. When Dial : Overlap is set, the digits are signalled individually in Information messages.
-
Page 33: Dialling Mode
® TS350 Basic Rate Euro ISDN Test Set During a call DTMF tones can be sent end to end when the number keys, are pressed. This is useful when using remote test equipment. If the key is pressed then KEYPAD information messages are sent when number keys number keys, are pressed. -
Page 34: 3.1Khz Audio Call
® TS350 Basic Rate Euro ISDN Test Set 3.1kHz Audio Call To make a 3.1kHz bearer voice call, select 3.1kHz from the Test Menu. 14:20 Test Menu BER Test Speech 3.1kHz Audio Teleservices ↵ ↵ Enter the B channel number you want to call on and press the ↵... - Page 35 ® TS350 Basic Rate Euro ISDN Test Set 14:20 3.1kHz Call Enter Number: 01633123123 ↵ ↵ L2 USR RR_C TEI=0 L3 USR SETUP When the called number connects, you will be presented with the call in progress screen: 14:20 3.1kHz Audio...
-
Page 36: Receiving A Voice Call
® TS350 Basic Rate Euro ISDN Test Set Receiving a Voice Call When your TS350 receives a compatible incoming Setup message (incoming call) the piezo sounder will ring and you will be prompted with the screen: 14:20 Test Menu Incoming call... -
Page 37: Teleservice Tests
Basic Rate Euro ISDN Test Set Teleservice Tests The TS350 can automatically check for Teleservice HLC (Higher Layer Compatibility) support on the line by making a series of self calls to the number of the line under test and inspecting the incoming network Setup message for the appropriate HLC information element. - Page 38 ® TS350 Basic Rate Euro ISDN Test Set 14:20 Teleservices Teletex F200: Videotex: Telex F60: MHS X400: 14:20 Teleservices MHS X400: OSI X200: Mainteneance: Management: Teleservices tested individually highlighting ↵ ↵ Teleservice to be tested and pressing , or all services can be tested automatically.
- Page 39 ® TS350 Basic Rate Euro ISDN Test Set When prompted to enter Own number:, enter the number of the ↵ ↵ ISDN line under test and press to start the automatic test sequence. 14:20 Teleservices Own Number: 01633123456 ↵ ↵...
- Page 40 ® TS350 Basic Rate Euro ISDN Test Set 14:20 Teleservices Teletex F200: Videotex: Telex F60: MHS X400: 14:20 Teleservices MHS X400: OSI X200: Mainteneance: Management: To conduct a single Teleservice test highlight and select the Teleservice to be tested 14:20...
-
Page 41: Supplementary Service Tests
Mixed Mode: Teletex F220: Supplementary Service Tests The TS350 can automatically check for Supplementary Service support on the line by making a series of self calls to the number of the line under test and inspecting the incoming network Setup message for the appropriate information elements. - Page 42 Suppl. Serv. SUB: CLIP: CLIR: DDI/MSN: the TS350 makes an outgoing self call and inspects the incoming network Setup message for a Called Party Number information element. If this is present then the line supports DDI (Direct Dialling IN). SUB: the TS350 makes an outgoing self call containing a sub...
-
Page 43: Automatic
If this is present with valid number contents, then the line supports CLIP (Calling Line Identity Presentation). CLIR: the TS350 makes an outgoing self call with the Calling Party Number information element set to restricted and inspects the incoming network Setup message. - Page 44 ® TS350 Basic Rate Euro ISDN Test Set When prompted to enter Own number:, enter the number of the ↵ ↵ ISDN line under test and press to start the automatic test sequence. 14:20 Suppl. Serv. Own Number: 01633123456 ↵ ↵...
-
Page 45: Manual Ddi/Msn/Sub/Clip/Clir
® TS350 Basic Rate Euro ISDN Test Set 14:20 Suppl. Serv. SUB: CLIP: CLIR: Manual DDI/MSN/SUB/CLIP/CLIR To conduct a manual Supplementary service test highlight and select the service to be tested 14:20 Suppl. Serv. Automatic DDI: SUB: CLIP: ↵ ↵... -
Page 46: Manual Tp
® TS350 Basic Rate Euro ISDN Test Set You are presented with the test progress message and the result upon completion. 14:20 Suppl. Serv. Testing... CLIP 14:20 Suppl. Serv. Automatic DDI/MSN: SUB: CLIP: Manual TP To test TP manually, select TP from the menu: 14:20 Suppl. - Page 47 ↵ ↵ B1 SPEECH OUT Note: After you have successfully suspended the call, you can physically disconnect the TS350 from the S bus and then reconnect within 3 minutes. To resume the call, select the Resume ID: 14:20 Suppl. Serv.
-
Page 48: Voltages
Supplementary Voltages ↵ ↵ The TS350 measures the battery, DC supply and the ISDN interface voltages. This feature is useful to ensure that the network voltages are within specification. If not within the limits, then you may have a network or NT1 fault. -
Page 49: Recorded Data
® TS350 Basic Rate Euro ISDN Test Set Battery: The NiMH batteries typically operate in the range 2.2 to 2.7volts. You will have up to 7 hours continuous use when the battery has been charged to 2.7 volts (off charge). -
Page 50: Trace L1/L2/L3
® TS350 Basic Rate Euro ISDN Test Set After selecting one of the Recorded Data menu items you can use the keys below to move through the listings Short press to scroll down one line. Long press (>1 sec) to page down 6 lines. - Page 51 ® TS350 Basic Rate Euro ISDN Test Set be filtered to display the options selected in the Setup menu item Trace as shown below: • Layer 1 INFO states • Layer 2 frame types • Layer 2 RR frames •...
-
Page 52: Number Log
® TS350 Basic Rate Euro ISDN Test Set Layer 3 messages: Buffer Call Line# Channel Message type 006 U 001 SETUP For a listing of all Layer 1 Alarm states, Layer 2 frame types and Layer 3 message types see Appendix . - Page 53 ® TS350 Basic Rate Euro ISDN Test Set The Setup menu is shown below: 14:20 Setup TEI: Auto Language:English Term: 100ohm Set Date & Time 14:20 Setup Set Date & Time Codec: A Law Sub Address:NSAP 6 Terminal No 14:20...
-
Page 54: Tei
® TS350 Basic Rate Euro ISDN Test Set The current selection is shown with a * next to the i t em in the sub menu. To exit a sub menu without making a new setting, press the key. This menu allows you to set an automatic TEI assignment procedure as used on a Point to Multipoint (PMP) S bus, or to select a Fixed TEI as used for example by iSPBXs. -
Page 55: Term
The S interface transmit and receive pairs can be terminated with a 100ohm resistor across each pair, or left high impedance - Hi Z. If the TS350 is the only item on the S bus then use the 100 ohm termination setting. If the S bus is already terminated by another terminal, then use the Hi Z setting. -
Page 56: Coding Law
11 20 00 Coding Law The TS350 will support either the A law coding algorithm as used in Europe or the µ (mu) law coding algorithm as used in the USA and Japan. Free Datasheet http://www.Datasheet4U.com... -
Page 57: Sub Address
You will be returned to the Setup menu with the Sub Address type selected shown. Terminal No If you enter a Terminal No, the TS350 will send this number in Setup messages as the Calling Party Number information element and Free Datasheet http://www.Datasheet4U.com... -
Page 58: Set Default
01291654321 L2 USR RR_C TEI=0 Enter the number you wish to assign to the TS350 and press the ↵ ↵ key to save the number. The number is saved and you are returned to the Setup menu. This number is cleared when the unit is switched off. -
Page 59: Contrast
® TS350 Basic Rate Euro ISDN Test Set When you set a parameter to a non-default value, the * will be removed. All setup parameters (except Terminal No) are stored in non volatile memory and will be maintained even if the batteries are flat or removed. -
Page 60: User Messages
When Layer 1 activation is complete the TS350 indicates this by either the S or U LED flashing green depending upon the interface that is connected. If the TS350 is unable to activate layer 1 at either the S or U interface, then the message: Layer 1 activation failure will be displayed and the S or U LED will flash red. -
Page 61: Layer 3 Messages
Speech 3.1kHz Audio Teleservices L2SABME RETRANSMISSION indicates that the TS350 has failed to get a network response to 4 transmissions of the SABME frame. Layer 3 Messages The TS350 will display all Layer 3 messages sent or received in the bottom line of the lower section of the screen wherever you are in the menu structure with the exception of the Trace screen. -
Page 62: B Channel Status
3.1kHz Audio Enter Number: 01633123123 L3 unknown message B Channel Status The TS350 shows the B channel status by displaying the call type on the bottom line of the lower section of the screen with scrolling messages. 14:20 Suppl. Serv. -
Page 63: Passive Monitor
NT to TE (Net) directions on the S/T bus. In this mode the TS350 must be bridged onto the link between the NT and the TE which may be an ISPBX or multiplexer. You can do this by using appropriate adapters e.g. - Page 64 ® TS350 Basic Rate Euro ISDN Test Set • Layer 3 messages • 'Display' Information Elements The trace buffer will store up to 200 lines of decode. An example of a captured trace is shown below. 14:20 Monitor 001 U 00 000 SABME C...
- Page 65 For a listing of all Layer 1 alarm states, Layer 2 frame types and Layer 3 message types see the Appendix. In addition Genius ISDN protocol analysis software can be used with the TS350 connected to a PC serial port using the RS232 lead. Free Datasheet http://www.Datasheet4U.com...
-
Page 66: Pstn Testing
Basic Rate Euro ISDN Test Set PSTN Testing The TS350 can test analogue PSTN lines and ports. This mode is very useful when testing combined ISDN S and analogue V5.1 combined NTs. The TS350 can also be used on regular analogue PSTN lines. - Page 67 In the on hook Monitor Mode you can listen in to the analogue line in high impedance monitor. The TS350 will not affect the use of other telephones on the line ↵ ↵ To make a call, press the...
-
Page 68: Ts350 Firmware Upgrade
Basic Rate Euro ISDN Test Set TS350 Firmware Upgrade The TS350 firmware is stored in FLASH memory, w hich allows you to upgrade the firmware release from your PC. The latest firmware releases are available on the Harris web site or you may purchase feature upgrades on CD. - Page 69 Upgrade executable file e.g. C:\Harris TS350\TS350Upgrade.exe and follow the on screen instructions. If you are using a TS350 Upgrade CD you may run the TS350Upgrade.exe executable file from your CDROM drive if you wish without copying the file to your hard drive.
-
Page 70: Ts350 Specifications
® TS350 Basic Rate Euro ISDN Test Set TS350 Specifications Protocol Layer 1 ETS300 012-1 Layer 2 ETS300 125 Layer 3 ETS300 102-1/2 BRI Interface S 4 wire RJ45 socket. Pins 4,5 Receive, Pins 3, 6 Transmit (to NT) U 2 wire RJ11 socket pins 2, 3 PSTN RJ11 socket pins 1, 4. -
Page 71: Weight
® TS350 Basic Rate Euro ISDN Test Set connected to 4 and 6 TS350 transmit data TS350 receive data connected 1 and 6 signal ground connected to 1 and 4 connected to pin 8 connected to pin 7 not connected... -
Page 72: Appendix
® TS350 Basic Rate Euro ISDN Test Set APPENDIX User messages Layer 1 INFO States INFO 0 No signal INFO 1 Terminal activation request INFO 2 Network activation request INFO 3 Terminal activation indication INFO 4 Network activation indication Layer 1 Error message... -
Page 73: Layer 2 Error Messages
® TS350 Basic Rate Euro ISDN Test Set UI_C SUPV_R SUPV_C XID_R XID_C ID_ASSIGN ID_DENIED ID_CHK_REQ ID_CHK_RESP ID_REMOVE ID_VERIFY Layer 2 Error Messages UNSOLICITED RESP. (A) UNSOLICITED RESP. (B) UNSOLICITED RESP. (C) UNSOLICITED RESP. (D) UNSOLICITED RESP. (E) SABME RE-ESTABLISH. -
Page 74: Clear Cause Number And Description
® TS350 Basic Rate Euro ISDN Test Set DISCONNECT RELEASE REL. COMP STATUS INQ INFO STATUS REST ACK RESUME RESUME ACK RESUME REJ SUSPEND SUSP. ACK SUSP. REJ RETRIEVE HOLD HOLD ACK REGISTER NOTIFY FACILITY UNKNOWN Clear Cause Number and Description 1 Unallocated Number 2 No Route to spec Transit Ntwk. - Page 75 ® TS350 Basic Rate Euro ISDN Test Set 29 Facility Rejected 30 Response to STATUS ENQUIRY 31 Normal, Unspecified 34 No Circuit/Chan Available 38 Network Out of Order 41 Temporary Failure 42 Switching Equip. Congestion 43 Access Info. Discarded 44 Requested Cct or Chan. Unavail.
-
Page 76: B Channel Status Messages
® TS350 Basic Rate Euro ISDN Test Set 111 Protocol Error Unspecified 127 Interworking Unspecified B Channel Status Messages n = B channel number i.e. B1 or B2 Bn IDLE Bn SPEECH OUT Bn SPEECH IN Bn 3.1KHZ OUT Bn 3.1KHZ IN...
Need help?
Do you have a question about the TS350 and is the answer not in the manual?
Questions and answers