Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Bannon 57941
- Page 1 12In. Utility Blower Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item #57941 READ & SAVE THESE INSTRUCTIONS...
- Page 2 Thank you very much for choosing a Bannon™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it.
-
Page 3: Table Of Contents
Table of Contents Intended Use ............................4 Packaging Contents ..........................4 Technical Specifications ........................4 Important Safety Information ....................... 4 Specific Operation Warnings ....................... 6 Grounding .............................. 6 Extension Cords ............................ 7 Before Each Use ............................ 8 Operating Instructions .......................... 8 After Each Use ............................ -
Page 4: Intended Use
Intended Use The Bannon 12 Inch Utility Blower can be used as a blower, circulator, or simply as a fan. It's perfect for exhausting fumes, ventilating confined spaces, and spot cooling. Packaging Contents Owner’s Manual (1) Blower (1) - Page 5 may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust.
-
Page 6: Specific Operation Warnings
measures reduce the risk of starting the tool accidentally. Store the blower when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use. ... -
Page 7: Extension Cords
grounding instructions, or if you are not sure the tool is properly grounded. Grounded Tools: Tools with 3-Prong Plugs Tools marked with Grounding Required have a 3-wire cord and 3-prong grounding plug. The plug must be connected to a properly grounded outlet. If the tool should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. -
Page 8: Before Each Use
cords from sharp objects, excessive heat and damp or wet areas. Grounded tools require a 3-wire extension cord. Double Insulated tools can use either a 2- or 3- wire extension cord. As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. -
Page 9: After Each Use
DO NOT operate without guards in place. Never allow air intake grill to become blocked. Never discharge flammable solvents or kerosene based chemicals through the grill. Do not use the blower in areas where flammable or combustible liquids, gases, vapors, dust, fibers, or filings may be present. -
Page 10: Troubleshooting
the possibility of electrical shock and/or electrocution. Be sure the fan blade has stopped rotating before placing any objects or fingers near the grill. Do not pressure-wash the blower. Visually check all fasteners and individual components for loose or broken parts. Tighten or replace items as required, with genuine, factory approved replacement parts only. -
Page 11: Parts Diagram
Failure Possible Cause Corrective Action 1) Fan is jammed against housing. 1) Replace fan blade if necessary. 2) Capacitor wire has broken/come Unit runs but fan 2) Repair/replace wires/capacitor as loose, capacitor has failed. does not turn necessary. 3) Housing has been damaged such 3) Replace entire blower unit. -
Page 12: Parts List
Parts List Reference Part Description Quantity Front Guard Blade Capacitor Back Guard Hook Power Cord Rocker Switch Rubber Foot Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence. -
Page 13: Limited Warranty
Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only ("You" or ''Your'') that the Bannon product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of two years from date of purchase. - Page 14 Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.com Made in China Page 14 of 14...
Need help?
Do you have a question about the 57941 and is the answer not in the manual?
Questions and answers