Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for D3FY SPORTS VERT3X
-
Page 2: Table Of Contents
TROUBLE SHOOTING.................7 VERT3X PARTS LIST................8 WARRANTY..................10 INCLUDES • 17.27mm (.68 CALIBER) VERT3X PAINTBALL MARKER • 30.48cm (12”) ONE PIECE BARREL (AUTOCOCKER THREAD) • SPARE PARTS KIT • TOOL KIT • BARREL BLOCKING DEVICE REQUIRED : CO2/HPA ONLY and Loader (not included) but are required for regulation play. -
Page 3: Important Safety Guidelines
• If you read these instructions and do not fully understand them, or are • Always treat the VERT3X marker as if it were loaded and able to fire. unsure of your ability to make necessary adjustments properly, call D3FY •... -
Page 4: Critical Safety Information
D3FY SPORTS reminds the user that Safety is Your Responsibility. Protect your eyes, face and ears at all times. Never shoot or point the VERT3X marker at a person that is not in designated paintball facility and without the proper Eyes/Face/Ears protection designed specifically for the sport of paintball and meets ASTM/CE specifications. -
Page 5: Important Co2 & Hpa Air Tank Safety Guidelines
Follow the warning labels listed on tanks. soon as an air tank is secured to the marker. •VERT3X Marker for use with refillable cylinders withstand input •Always follow the warning listed on Co2/HPA tank. pressure of 207bar (3,000psi) without catastrophic failure. -
Page 6: Getting Started
Fire” side. Located opposite side of “PUSH SAFE” on the trigger frame. position when not in use. 15. Push the safety button to the “SAFE” position. Caution: The VERT3X is now live and ready to fire. 9. Ready to Fire. Ⅰ GETTING STARTED... -
Page 7: Maintaining Your Vert3X Paintball Marker
MAINTAINING YOUR VERT3X 2. Pull upward on the Bolt Cocking Pin (I-05) to disconnect from the Striker. Remove the Delrin Bolt (I-04) by sliding it out the rear of the PAINTBALL MARKER Receiver/Body (X-20). 3. Wipe off any dirt,debris, or paint from the Delrin Bolt using a clean cloth. - Page 8 and Striker from the rear of the Receiver. Tip: Only remove the Striker Plug with the marker in the un-cocked 4. Insert the Delrin Bolt with the open face in first. Align the Bolt position. This will prevent the internals from springing out when the Cocking Pin with the Striker hole, and push down on the Pin to lock it Striker Spring is compressed.
-
Page 9: Troubleshooting
4. Once the Front Plug is removed. Pull out the Valve Spring (I-01) Solution: Replace Striker O-ring and add a few drops of oil. and Cup Seal/Valve Pin (I-02). 5. Rear internals are not properly installed. Note: Inspect the Cup Seal/Valve Pin for any signs of damage. Solution: Follow Reassemble Rear Internal steps. - Page 10 D3fy Sports strongly recommends that you send your package via Solution: Clean Bolt, Barrel and Receiver. a carrier which provides a tracking number. D3fy Sports is not liable for any packages lost in transit. We are only responsible for product 3.
- Page 11 NOTES...
-
Page 12: Vert3X Parts List
Trigger Spring I-08 Striker I-09 Striker Spring I-10 Striker Spring(High Velocity) I-13 Striker Buffer X-15 Striker Plug O-04 Velocity/Spring Guide O-ring I-15 Velocity/Spring Guide X-16 Rubber Wrap Grip S-08 Grip Screw I-16 Sear Spring I-18 Sear Ⅰ VERT3X PARTS LIST... - Page 14 NOTES...
- Page 15 1462 W. Holt Ave. Pomona, CA 91768 www.D3FYSPORTS.com...
Need help?
Do you have a question about the VERT3X and is the answer not in the manual?
Questions and answers