Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Rextron Technology, Inc. AcroGear Series
- Page 2 Package Contents DAAG-114 (w/ Audio) 4-Port AcroGear (DAAG-114) User’s manual Rubber foot pad x 1 set DADG-122 (Dual Display w/ Audio) 2-Port AcroGear (DADG-122) User’s manual Rubber foot pad x 1 set DADG-124 (Dual Display w/ Audio) 4-Port AcroGear (DADG-124) User’s manual Rubber foot pad x 1 set...
-
Page 3: Table Of Contents
Table of Content Introduction……………………………………………..1 Overview ..........……………….1 Features ..........……………….1 System Requirements…………………………………2 Console side ........……………….2 Computer side........……………….2 Installations……………………………………………..3 PC BIOS Notice ........……………….3 Console Connection......……………….4 Computers Connection ..... ………………...5 Operations………………………………………………6 Front Panel........………………..6 Hotkey commands………………………………………8 Rack Mount Kit ........ ………………11 Appendices……………………………………………12 Specifications ………………………………………….12 Troubleshooting ……………………………………13 Please read this manual thoroughly and follow the... -
Page 4: Introduction
Computer selecting is as easy as front panel button pressing. The built-in USB hub ensures smooth switching from one computer to the other. The AcroGear series provide the easiest way to manage multiple computers with USB interface and share USB peripherals among computers. -
Page 5: System Requirements
System Requirements ------------------------ Console side One / Two DVI monitor (Two for dual display type) One USB Keyboard One USB mouse Computer side Each USB-enabled computer must be connected to the DAAG-114 / DADG-124 by One DVI cable for monitor, as shown below One USB A-B cable with Type-A and Type-B plug for USB devices, as shown below... -
Page 6: Installations
2. In PNP AND PCI SETUP, set PNP OS INSTALLED to YES and set USB IRQ to ENABLED. Note: The AcroGear series are applicable for USB keyboard and mouse switching from one computer to the other. If you plan to share other... -
Page 7: Console Connection
Console Connection Before installation, make sure all devices and computers to be connected to the unit have been turned off. Plug a monitor to the Console's DVI port; plug a USB keyboard and a USB mouse to any two of the Console's USB ports as shown below. -
Page 8: Computer Connection
Computer Connection Use a male-to-male cable to connect from a computer's DVI port to DAAG-114 / DADG-124 DVI port of PC side. Use a USB A-B Cable to connect from the DAAG-114 / DADG-124 USB port (B connector, square connector) to the USB port on the corresponding computer (A connector, flat connector), as shown below. -
Page 9: Operations
Operations ------------------------ Front Panel 1. On-line LED & Selected LED When the LED turns green, the connected computer is powered-on. When a computer is selected, its corresponding red LED illuminates. 2. Pushbuttons Each computer has a button associated with it on the front panel for selection. - Page 10 Adjust the Video Signal To adjust the optimal video signal strength corresponding to the length or quality of DVI cable, the user can press “FUNC” button combining with the other pushbuttons. Step 1. Press “FUNC” button three times, the LED of “FUNC”...
-
Page 11: Hotkey Commands
While the “FUNC” button is holding, press pushbutton “2” for selecting audio port 2. While the “FUNC” button is holding, press pushbutton “3” for selecting audio port 3. While the “FUNC” button is holding, press pushbutton “4” for selecting audio port 4. While the “FUNC”... - Page 12 Left Ctrl + Left Ctrl + F1 To abort the Auto Scan mode, press the left Ctrl key twice. When Auto Scan detects any keyboard or mouse activity, it suspends the scanning till the activity stops; it then resumes with the next computer in sequence. The length of the Auto Scan interval (Scan Rate) is adjustable, see below.
- Page 13 Enforce the USB followed with the selected computer by pressing the following hotkey Left Ctrl + left Ctrl + U 2. USB 2: pressing the hotkey below to ON/OFF the USB-Port Rule Left Ctrl + left Ctrl + F8 ON: USB-Port selection followed with computer selection OFF: USB-Port selection followed with USB 1 NOTE: Please make sure that USB device linking procedure has accomplished before switching to the next computer.
-
Page 14: Rack Mount Kit
Rack Mount Kit ------------------------ The figure below shows how to attach optional mounting brackets and cable support (RMK04) to the DAAG-114 / DADG-124 for standard 19-inch rack cabinet. -
Page 15: Appendices
Appendices ------------------------ ․Specifications Specification DAAG-114 DADG-124 Console Port Computer Port Front panel push button Front panel FUNC button Hot plug-and-play Automatic scan interval 3, 8, 15, 30 seconds Cable Length (Max) 3M(10ft) for USB Computer ON-LINE LED Computer Selected LED USB Type B x 4 Computer Monitor... -
Page 16: Troubleshooting
․Troubleshooting: Ensure that all cables are well seated. Label the cable for each computer to avoid confusion when connected to the unit. The unit have built-in power protection that works automatically when needed. When it works, USB communication halts and the only way to restart the unit properly is to remove all power sources (USB patch cables and power adapter), wait a few seconds, apply power sources and start again. -
Page 17: Limited Warranty
resolution Improper video settings of To adjust the optimal video signal strength is not good. DAAG-114 / DADG-124 corresponding to the length or quality or DVI cable, the user can press “FUNC” button combing with the other pushbuttons. Limited Warranty IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT OR INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFIT, LOSS OF BUSINESS, OR FINANCIAL LOSS WHICH MAY BE CAUSED BY THE USE OF THE...
Need help?
Do you have a question about the AcroGear Series and is the answer not in the manual?
Questions and answers