Subscribe to Our Youtube Channel
Summary of Contents for Sigma HDTV5
- Page 1 SIGMA HDTV5 USB V1 User’s Manual Version 1.0 Notice This device has been approved by FCC for a home appliance and is suitable for all residential areas.
-
Page 2: Table Of Contents
Package contents 1-3. Description of each function Chapter 2. Installation 2-1. Before installing the SIGMA HDTV5 USB V1 2-2. Connecting the USB cable 2-3. Connecting the antenna cable 2-4. Connecting the other devices (VCR, Camcorder etc) 2-5. Installing the Driver and Program Chapter 3. -
Page 3: Chapter 1. Before Getting Started
Chapter 1. Before getting started 1-1. System requirements System configurations To use SIGMA HDTV USB V1, the following configurations are needed. Operating system - Windows XP (Service pack1 or higher) * Periphrals - HDD (Ultra DMA 66 or higher) - Desktop PCs or laptops built-in USB 2.0 port (PCI or PCMCIA USB 2.0 card) -
Page 4: Package Contents
A/S center for a quick product exchange. SIGMA HDTV5 USB V1 ATSC broadcast receiver Installation CD Used for installing drivers and application programs for SIGMA HDTV5 USB V1 User’manual Used for the installation and usage guide of SIGMA HDTV5 USB V1 Remote contral (Including battery) -
Page 5: Description Of Each Function
Power LED Receiver of Remote control ( Remote control sensor .) READY : Status of receiving the digital broadcasts of SIGMA HDTV5 USB V1. If the broadcast signal is weak, the READY will be ON. (Normal status is OFF) Back Antenna In: Used for receiving HDTV, Analog TV or Cable TV signals S-VIDEO In: Used for receiving S-Video signals from the external devices (VCR, camcorder...) -
Page 6: Chapter 2. Installation
4. Make sure that your OS(operating system) is MS Windows XP(service pack 1 or higher) SIGMA HDTV5 USB V1 is suitable for Microsoft Windows XP OS, service pack 1 or higher. Lower OS versions such as Windows98, Windows2000 and Windows ME may cause a serious system conflict. -
Page 7: Connecting The Usb Cable
2-2. Connecting the USB cable 1. Connect the USB cable to the USB port of SIGMA HDTV5 USB V1 2. Connect the other side of the USB cable to the USB port of your system as drawn below. Connecting USB cable 2-3. -
Page 8: Connecting The Other Devices (Vcr, Camcorder Etc)
2. Connect Composite output of an external video device to Composite input of SIGMA HDTV5 USB V1 with the composite conversion cable. . Audio connection 1. Connect SIGMA HDTV5 USB V1 to an external Video device with the sound cable as drawn below S-Video Cable... - Page 9 3. Run ‘SETUP.EXE’ in ‘Driver’ folder of in your CD-ROM drive. 4. SIGMA HDTV USB V1 driver setup window appears then click [Next]. 5. While SIGMA HDTV USB V1 driver files being copied, “SIGMA HDTV5 USB V1 driver has not passed...
- Page 10 Windows Logo testing to verify its compatibility with Wndows XP” appears then click [Contiue Anyway]. 6. After being completed installation, click the [Finish]. . Program installation...
- Page 11 1. Run ‘SETUP.EXE’ in your CD-ROM Drive. 2. SMPlayer Setup window appears then click [Next]. 3. Installation directory appears then click [Next]. If you want to change the Installation directory, click “Searching” to set your directory 4. SMPlayer Setup window appears then select a type of broadcast reception. 5.
- Page 12 6. After being completed program installation, click [Finish].
-
Page 13: Chapter 3. Using Sigma Hdtv5 Usb V1
Chapter 3. Using SIGMA HDTV5 USB V1 3-1. Basic funtion SMPlayer is a TV viewing tool for your favorable digital TV programs. In case of connecting to an external video device, you can also enjoy a video in the SMPlayer Running the program Double-click ‘[... -
Page 14: Setting The Input Mode
FILE: File play mode (*.TRP, *.MPG, *.AVI, *.WMV). DV : Digital Video input mode(digital camcorder) D-VHS: D-VHS input mode (D-VHS player) [NOTE] To use VIDEO, SVHS or DVHS mode, appropriate external device should be connected to the SIGMA HDTV5 USB V1. Setting the TV channel Volume... - Page 15 Channel window (Channel memory/ delete) This function is to scan, save or delete all available TV channels from the over the air or digital cable. The channel window appears if you click [ Switch to the preferred channel mode Delete all scanned channels. Delete the watching channel (the channel on the screen) Add the watching channel (the channel on the screen) Scan available TV channels automatically...
-
Page 16: Capture Function
3-2. Capture function Saving the still image This function is to save a motion video into a still image . How to save the still image Click [ ]’ in the panel, the screen is saved as a file (When the file is saved, the file name is shown on the screen) Saving the video This function is to save a video into a motion video file How to save the video... -
Page 17: Other Functiosns
3-3. Other functions Reservation function This function is to reserve or record a TV program as pre-scheduled. Click ‘[ ]’ on the tray bar then select the ‘Reserve’as drawn below. Schedule window appears. Select “Add,” “Modify,” “Delete” or “Delete All” in the reservation list. [NOTE] . -
Page 18: File Play Mode
File play mode This mode is to play a video file that saved in your system 1. Click [ ]’or [ ]’to find a video file you want. “Open” window appears then choose a file and click [Open]. 3. The video file will be loaded in the TV window automatically. While playing the video file, you can easily control it by using buttons(play,pause,file open) and slide bar. -
Page 19: Time-Shift
Time -Shift This allows you to pause a live broadcast and return to it or moments and continue exactly where you left off. The live broadcast is saved in HDD space as much as its available free space. Therefore, you are able to watch and enjoy your favorite TV show like your VCR tape. -
Page 20: Menu
Menu This is a menu set for SMPlayer program. Click ‘Menu [ ] ‘in the panel or right mouse button in the window.. Still capture Save as a still image. Record Save as a video file Channel Window Show or hide the Channel window that can be memorized or deleted. Multi Screen The TV screen is devided into multi screen and shows in serial. - Page 21 Save configuration Show the configuration to save video or still image. Remocon option Remote control icon should be activated on the tray. OSD configuration Set the color or size of OSD. OSD stands for On Screen Display. File control Whenever pressing Hot key(Ctrt+L/R), the play position is moved as set in the menu. (This function can be used in File mode only.) Subtitle Set a subtile supported by a video file.
- Page 22 Quit the SMPlayer program. Appendix. Remote Control Replacing batteries - Use a 3 V lithium battery for the replacement. Basically, the battery is provided when you purchase SIGMA HDTV5 USB V1. 1. Pull down the battery tray of the remote control.
- Page 23 Descriptions of the remote control Numeric buttons Volumn Up/Down Previous channel EPG funtion Paly/ Pause Stop Previous file Next file Aspect ratio Zoom funtion Power on / off Virtual channel Mute Channel Up/ Down Favorite channel selection Record still image Record movie Forward slowly Rewind slowly...
Need help?
Do you have a question about the HDTV5 and is the answer not in the manual?
Questions and answers